1. Introduction
The Andeli CUT-80DY is a versatile 2-in-1 industrial machine designed for both plasma cutting and MMA (Manual Metal Arc) welding. It features a high-frequency (HF) arc start, 2T/4T torch control modes, and a built-in air compressor, making it suitable for cutting various metal plates with efficiency and precision. This manual provides essential information for the safe and effective operation, setup, and maintenance of your CUT-80DY machine.
2. Safety Information
Always prioritize safety when operating welding and cutting equipment. Failure to follow safety precautions can result in serious injury or death.
- Electric Shock: Can kill. Ensure proper grounding. Do not touch live electrical parts. Wear dry welding gloves.
- Fumes and Gases: Can be hazardous. Work in a well-ventilated area. Use fume extractors if necessary.
- Arc Rays: Can burn eyes and skin. Wear a welding helmet with appropriate shade filter and protective clothing.
- Fire and Explosion: Welding and cutting can cause fire or explosion. Keep flammable materials away from the work area. Have a fire extinguisher readily available.
- Hot Parts: Can cause severe burns. Allow equipment to cool before handling.
- Noise: Excessive noise can damage hearing. Wear ear protection.
- Compressed Air: Handle compressed air lines and components with care. Ensure connections are secure.
Always read and understand all safety warnings and instructions provided with the equipment and consumables.
3. Included Components
The Andeli CUT-80DY package typically includes the following items:
- Andeli CUT-80DY Main Unit
- P80 Plasma Cutting Torch (10 meters)
- MMA Electrode Holder (5 meters)
- Ground Clamp
- Hose Hoops (x2)
- Plasma Electrodes (x10)
- Plasma Tips (x10)
- Nozzle Shields (x10)
- Wheels (for portability)
- User Manual
4. Setup Instructions
Follow these steps to set up your CUT-80DY machine for operation:
- Power Connection: Connect the machine to an appropriate power supply. The CUT-80DY supports 1-phase AC 220V or 3-phase 385V. Ensure the power source matches the machine's requirements and is properly grounded.
- Ground Clamp Connection: Attach the ground clamp cable to the designated 'CUT/MMA Ground Cable' terminal on the front panel. Secure the ground clamp to the workpiece or work table, ensuring good electrical contact.
- Plasma Torch Connection (for Cutting): Connect the P80 plasma torch to the 'Torch Switch' and 'Pilot Arc' ports on the front panel. Ensure all connections are tight.
- MMA Holder Connection (for Welding): If performing MMA welding, connect the MMA electrode holder cable to the 'MMA V/A cable' terminal.
- Air Supply: The CUT-80DY has a built-in air compressor. For optimal performance, ensure the air intake is clear. If using an external air pump for increased cutting thickness (up to 25mm), connect it to the machine's air inlet port, typically located on the side or rear.
- Consumables: Install the appropriate electrode, tip, and nozzle shield into the plasma torch head.
5. Operating Instructions
The CUT-80DY offers both plasma cutting and MMA welding functionalities. Ensure proper safety gear is worn before operation.
5.1 General Operation
- Power On: Turn on the main power switch of the machine. The LED display will illuminate.
- Mode Selection: Use the control panel to select between 'CUT' (plasma cutting) or 'MMA' (welding) mode.
- Parameter Adjustment: Adjust the output current (Amperage) and other relevant parameters using the control knobs and buttons. The LED display provides real-time feedback on settings.
- Gas Check Function: Before cutting, utilize the 'GAS-CHECK FUNCTION' to verify that the gas path is unobstructed and air is flowing correctly.
- Arc Start: The machine uses a High-Frequency (HF) uncontact arc start method for plasma cutting, providing easy and reliable ignition.
5.2 Plasma Cutting (CUT Mode)
- Cutting Thickness: The built-in air pump supports cutting up to 20mm thick plates. With an external air pump, the cutting thickness can be extended to 25mm.
- 2T/4T Function:
- 2T (Non-Self Lock): Press and hold the torch trigger to maintain the arc. Release to stop. Suitable for short cuts.
- 4T (Self-Lock): Press the torch trigger once to start the arc, press again to stop. Reduces hand fatigue during long cuts.
- Pre-Gas/Post-Gas Function: This function controls the gas flow before and after the arc. Pre-gas prepares the nozzle, while post-gas cools the torch and protects the cut area, extending consumable life.
- Wiremesh Cut: The machine is suitable for cutting panels with large gaps, indicating stable arc performance.
5.3 MMA Welding (MMA Mode)
- Select MMA mode and adjust the current according to the electrode type and material thickness.
- Ensure proper electrode selection and technique for desired weld quality.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your CUT-80DY machine.
- Cleaning: Regularly clean the machine's exterior and ventilation openings to prevent dust and debris buildup, which can hinder cooling.
- Air Filter: Check and clean or replace the air filter for the built-in compressor periodically to maintain efficient air flow. The built-in air pump is designed to be oil-free and maintenance-free, reducing routine upkeep.
- Consumables: Inspect plasma torch electrodes, tips, and nozzle shields regularly. Replace them when worn to ensure consistent cut quality and prevent damage to the torch.
- Cable Inspection: Check all cables (power, ground, torch, MMA holder) for damage, cuts, or loose connections before each use.
- Cooling System: The machine features a fast intelligent cooling system with a condenser. Ensure adequate airflow around the machine for effective heat dissipation, especially during long cutting sessions.
7. Troubleshooting
The CUT-80DY is equipped with detection features to assist in diagnosing issues. Refer to the LED display for indicators such as 'Over current check', 'Temperature check', and 'Voltage check'.
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not power on | No power supply; Faulty power cable; Internal fuse blown | Check power connection and circuit breaker; Inspect power cable; Contact service for fuse replacement. |
| No arc in CUT mode | No air flow; Worn consumables; Poor ground connection; Incorrect settings | Check air supply and 'GAS-CHECK FUNCTION'; Replace electrodes/tips; Ensure ground clamp has good contact; Verify current and mode settings. |
| Poor cut quality / Inconsistent arc | Worn consumables; Insufficient air pressure; Incorrect cutting speed/height | Replace consumables; Check air pressure (built-in or external); Adjust cutting parameters. |
| Over current/Temperature/Voltage warning | Overload; Insufficient cooling; Input voltage fluctuation | Reduce duty cycle or current; Ensure proper ventilation; Check input voltage stability. Allow machine to cool down if temperature warning is active. |
| No arc in MMA mode | Poor ground connection; Incorrect current setting; Wet electrode | Ensure ground clamp has good contact; Adjust current; Use dry electrodes. |
8. Specifications
Technical specifications for the Andeli CUT-80DY machine:
| Feature | Specification (CUT-80DY) |
|---|---|
| Model | CUT-80DY |
| Input Voltage | 1PH AC 220V / 3PH 385V |
| Function | MMA / CUT (2-in-1) |
| Rated Input Power (MMA) | 11.8 kVA / 13.2 kVA |
| Rated Input Power (CUT) | 13.8 kVA / 17.1 kVA |
| Rated Output Current | 30-320A |
| Efficiency | 80% |
| Protection Grade | IP21S |
| Insulation Grade | F |
| Method of Arc Start | Uncontact (HF) |
| Dimension (L x W x H) | 640 x 335 x 575 mm |
| Weight | 56 KG |
| Cutting Thickness (Built-in Air Pump) | 20mm |
| Cutting Thickness (External Air Pump) | 25mm |
9. User Tips
- For cleaner cuts on thicker materials, consider using an external air compressor to achieve the maximum 25mm cutting thickness.
- Experiment with the 2T and 4T torch modes to find what works best for different cutting tasks and to reduce hand fatigue during extended use.
- Always ensure your workpiece is clean and free of rust or paint for the best ground connection and arc stability.
- Keep a supply of spare consumables (electrodes, tips, nozzle shields) as they wear out over time and affect cut quality.
10. Warranty and Support
The Andeli CUT-80DY machine comes with a 2-year warranty from the date of purchase, covering manufacturing defects and malfunctions under normal operating conditions. For technical support, troubleshooting assistance, or warranty claims, please contact Andeli customer service.
Contact Information:
- WhatsApp: +86 19373185636
Please have your product model and purchase details ready when contacting support.