DAKEFPV F435 V3/V4

Contents

DAKE F435 V3/V4 Flight Controller & ESC Stack Instruction Manual

Model: F435 V3/V4

1. Overview

The DAKEFPV F435 V3/V4 Flight Controller (FC) and Electronic Speed Controller (ESC) Stack is a high-performance solution designed for RC FPV racing drones. This stack integrates a powerful F435 Flight Controller with a BLS 4-in-1 ESC, offering robust features and reliable operation for demanding flight applications.

DAKE F435 V3/V4 FC ESC Stack assembled
Figure 1.1: Assembled DAKE F435 V3/V4 Flight Controller and ESC Stack.

The DAKE F435 V3/V4 FC ESC Stack provides a compact and powerful solution for FPV drones.

DAKE F435 V3/V4 FC ESC Stack disassembled
Figure 1.2: Disassembled view of the F435 Flight Controller and 70A 4-in-1 ESC.

This image shows the individual components of the stack: the F435 Flight Controller and the 70A 4-in-1 ESC.

Key features of DAKE F435 BLS 70A Stack
Figure 1.3: Key features of the DAKE F435 BLS 70A Stack.

Highlights include BetaFlight/ArduPilot support, real 70A output, dual ICM42688-P gyroscopes, support for 8 motors, 4x LEDs, 5V/12V 3A BEC, 16M onboard FLASH, external GPS module support, 35V 1000uF Low ESR Capacitor, DJI Air Unit direct plug interface, and a built-in barometer.

2. Package Contents

The DAKEFPV F435 stack is available in several configurations. Please verify your package against the options below.

2.1 Option 1: DAKEFPV F435 70A 30x30 STACK

Package contents for DAKEFPV F435 70A 30x30 STACK
Figure 2.1: Package contents for the F435 70A 30x30 Stack.

This option includes the complete stack and all necessary accessories for assembly.

  • DAKEFPV F435 Flight Controller x 1
  • DAKEFPV BLS 70A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 silicone O Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1
  • M3*8.1mm Silicone Grommets (for ESC) x 1
  • SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  • SH 1.0mm 75mm-length 8pin Cable x 1
  • M3*30mm Inner-hexagon Screws x 5
  • GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  • XT60 Power Cable (70mm) x 1

2.2 Option 2: DAKEFPV F435 30x30 FC

Package contents for DAKEFPV F435 30x30 FC
Figure 2.2: Package contents for the F435 30x30 Flight Controller.

This option includes only the F435 Flight Controller and its specific accessories.

  • DAKEFPV F435 Flight Controller x 1
  • Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 5
  • FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  • GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

2.3 Option 3: DAKEFPV 8S 70A 4 in 1 ESC

Package contents for DAKEFPV 8S 70A 4 in 1 ESC
Figure 2.3: Package contents for the 8S 70A 4-in-1 ESC.

This option includes only the 8S 70A 4-in-1 ESC and its specific accessories.

  • DAKEFPV 8S 70A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor (Buy 12S ESC Send 63V1000uf Capacitor) x 1
  • FC 12-pin to ESC 8-pin cable (for connecting FC to ESC) x 1
  • XT60 x 1

3. Setup & Installation

3.1 Dimensions and Mounting

Dimensions of F435 Flight Controller and ESC
Figure 3.1: Dimensions of the F435 Flight Controller and ESC.

The F435 FC measures 36x36x8mm with 30.5x30.5mm mounting holes. The ESC measures 45.4x42.8x6.5mm with 30.5x30.5mm mounting holes. The assembled stack height is 15.8mm.

Important Stack Installation Note:

Important installation note for DAKE F435 stack
Figure 3.2: Critical installation considerations.

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC. It's critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

3.2 Wiring Diagram

Refer to the comprehensive wiring diagram for connecting the Flight Controller, ESC, motors, and other peripherals.

Full wiring diagram for DAKE F435 FC and ESC stack
Figure 3.3: Complete wiring diagram for the F435 FC and ESC stack.

This diagram illustrates connections for motors, LEDs, USB, GPS, receivers, and video systems.

Note 1: In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.

3.3 Direct Soldering Pads

The FC and ESC can also be connected via direct soldering. The soldering pads definition is as follows:

Direct soldering pads definition for FC and ESC
Figure 3.4: Soldering pads for direct connection between FC and ESC.

This image details the soldering points for a direct, wired connection between the flight controller and the ESC.

The F435 FC supports direct plug-in for DJI Air Units and similar systems.

Cable connection with DJI O3 Air Unit
Figure 3.5: Cable connection with DJI O3 Air Unit.

Use the 6-pin cable that comes with the O3 Air Unit.

Cable connection with Caddx Vista Air Unit
Figure 3.6: Cable connection with Caddx Vista Air Unit.

Use the 6-pin cable that comes with the H743 stack (refer to accessory No.11 in package section).

Cable connection with DJI Air Unit V1
Figure 3.7: Cable connection with DJI Air Unit V1.

Use the 6-pin cable that comes with the H743 stack (refer to accessory No.11 in package section).

3.5 SBUS Receiver Connection

SBUS receiver connection importance notice
Figure 3.8: SBUS receiver connection details.

When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2). If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

Importance notice for ELRS receiver:

We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

4. Operating Instructions

4.1 Motor Support

The flight controller supports up to 8 motors, making it suitable for X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors.

F435 Flight Controller M1-M8 motor pads
Figure 4.1: Motor pads M1-M8 on the F435 Flight Controller.

The FC provides dedicated pads for connecting up to 8 motors.

4.2 Battery Level Indicator (LiPo Checker)

The flight controller features a built-in 4-level battery capacity indicator. Upon connecting the battery, you can instantly check the battery level without needing external equipment.

F435 Flight Controller LiPo checker feature
Figure 4.2: LiPo checker on the F435 Flight Controller.

Visual indicators for battery voltage levels (FCC, 3V, 5V, 12V).

4.3 LED Light Bar Control

The LED pads at the corners of the flight controller allow you to connect and control LED light strips for customization. A long press of the BOOT button lets you switch between different lighting modes. Short presses of the BOOT button toggle between various preset light effects.

F435 Flight Controller LED light bar pads
Figure 4.3: LED light bar connection pads.

Connect your LED strips to these pads for customizable lighting effects.

5. Specifications

5.1 DAKEFPV F435 30x30 Flight Controller

FeatureSpecification
Main Control UnitSTM32F435
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENone
WIFINot supported
DJI Air Unit ConnectionSupports 6-pin socket direct plug-in and solder wire connection. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wiring changes needed.
FLASH (Black Box)16MB Flash
AmmeterSupported
Input Voltage3-8S LiPo Battery
UART Serial Ports8 groups
Buzzer PadSupported (BZ+, BZ- pads connect to 5V active buzzer)
BOOT ButtonSupported. Press and hold while powering to enter DFU mode for firmware flashing.
RSSI PadSupported. Located on the top front RS pad.
SmartPort/F.PortNot supported
Supported FirmwareBetaFlight (default factory firmware), ArduPilot
Firmware Target NameDAKEFPVF435
Mounting Holes30.5 x 30.5mm (4mm diameter)
Dimensions36 x 36 x 8 mm
Weight10.5g
F435 Flight Controller layout with pinouts
Figure 5.1: F435 Flight Controller layout with pinouts.

Detailed view of the F435 FC, showing various pads and components including Gyro (ICM42688P), 16MB Flash, LED, Buzzer LED strip, USB Type-C port, OSD Chip (AT7456E), GPS, ELRS, and VTX connections.

5.2 DAKEFPV BLS 70A 4 in 1 ESC

FeatureSpecification
Product NameDAKE 70A 4 in 1 ESC
FirmwareBLHeli_s/BLUEJay
Battery Input3-8S LiPo Battery
Continuous Current70A x 4
Maximum Current80A x 4 (for 10 seconds)
Built-in TVS DiodeYes
External Capacitor1000uF high-frequency low-ESR capacitor (included)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Output VoltageVBAT
AmmeterSupported (Scale=400, Offset=0)
ESC TelemetryNot supported
Mounting Holes30.5 x 30.5mm (4mm diameter)
Dimensions45.4 x 42.8 x 6.5 mm
Weight23.5g
BLS 70A 4-in-1 ESC circuit design improvements
Figure 5.2: ESC upgrade to 70A.

The circuit design has been greatly optimized. The copper thickness of the PCB has been upgraded from 2 ounces to 3 ounces, and the MOS tube has also been upgraded to a higher specification. The continuous current of a single channel has been upgraded to a total of 220A for four channels, and the peak current has been increased to 280A for 10 seconds, which can drive any of the most powerful 6S/4S motors without pressure. A new aluminum alloy heat sink has been added to quickly dissipate the heat of the MOS tube, making the output of the electronic speed controller more stable.

BLS 70A 4-in-1 ESC internal components
Figure 5.3: Internal components of the BLS 70A 4-in-1 ESC.

This image highlights the Driver Chips and MCU (BB21) on the ESC board.

TVS diode and filter capacitors on ESC
Figure 5.4: TVS diode and filter capacitors for surge protection.

The ESC includes a TVS protection diode, 21 imported Japanese TDK SMD filter capacitors, and a 1000uF ultra-large capacity low-resistance electrolytic capacitor to absorb voltage spikes and filter signal interference, ensuring smoother flight.

Built-in 16MB large memory FLASH on FC
Figure 5.5: Built-in 16MB large memory FLASH.

The FC continuously records flight status (sensor data, control commands, fault codes). Even in the event of a crash or power outage, the data can still be retrieved for accident analysis.

Gyro ICM42688P and Clean Power Supply
Figure 5.6: Gyro ICM42688P and Clean Power Supply.

The FC adopts an imported LDO power supply chip to independently power the onboard ICM42688P gyroscope, with a surge protection capability increased by 320%; it is equipped with a 22uF ultra-large filtering tantalum capacitor.

6. Troubleshooting

  • Flight Controller Not Recognized (DFU Mode): If the flight controller is not recognized by your computer or BetaFlight configurator, press and hold the BOOT button while connecting power to force it into DFU mode for firmware flashing.
  • SBUS Receiver Issues with DJI Air Unit: If your SBUS receiver is not recognized when a DJI Air Unit (O3/Link/Vista/Air Unit V1) is also connected, you may need to disconnect the SBUS signal wire from the Air Unit harness. Carefully remove or cut the SBUS wire from the 6-pin harness connector and insulate it.
  • ELRS Receiver Issues with DJI Air Unit: Similar to SBUS, if an ELRS receiver is not recognized when a DJI Air Unit is connected, disconnect the SBUS signal wire from the Air Unit harness.
  • Voltage Spikes / Burnout Prevention: Always install the provided Low ESR capacitor to prevent damage from voltage spikes during power-up.
  • Short Circuit During Installation: Ensure sufficient space between the FC, ESC, and frame, especially if mounting inverted. Improper installation, particularly contact between the FC's USB interface and the ESC, can cause a short circuit and is not covered under warranty.

7. Maintenance

  • Regular Inspection: Periodically inspect all solder joints and connections for any signs of damage, corrosion, or loose wires.
  • Cleaning: Keep the FC and ESC free from dust, dirt, and moisture. Use a soft brush or compressed air for cleaning. Avoid using liquids directly on the electronics.
  • Firmware Updates: Regularly check for firmware updates for both the Flight Controller (BetaFlight/ArduPilot) and the ESC (BLHeli_s/BLUEJay) to ensure optimal performance and access to new features.
  • Capacitor Check: Ensure the Low ESR capacitor remains securely connected and undamaged. Replace if any signs of wear or bulging are observed.
  • Physical Protection: Consider using appropriate protective enclosures or conformal coating for added durability in harsh environments.

8. Warranty & Support

This product is covered by a limited warranty against manufacturing defects. Please retain your proof of purchase for any warranty claims. Damage resulting from improper installation, misuse, modification, or accidents is not covered under warranty.

For technical support, firmware updates, or further assistance, please refer to the official DAKEFPV website or contact your retailer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.