RADIOMASTER TX15

Contents

Radiomaster TX15 Radio Controller User Manual

Model: TX15 | Brand: RADIOMASTER

1. Introduction

Thank you for choosing the Radiomaster TX15, a versatile remote control system featuring dual-band capabilities with 2.4GHz technology. Whether you're a beginner or a seasoned professional, the TX15 is designed to meet your needs, offering precision, flexibility, and reliability.

Please read this guide carefully before operating your new remote to ensure safe and optimal use. As we continually enhance our software and hardware, updated versions of this manual may be released. For the latest information and resources, please visit our website.

The TX15 is pre-installed with factory approved EdgeTX firmware. To download the latest software manual, please visit the RadioMaster website: www.radiomasterrc.com.

Further firmware information can be found at: www.edgetx.org (EdgeTX) and www.expresslrs.org (ExpressLRS).

For a detailed user manual in PDF format, please refer to the official document: TX15 User Manual (PDF).

2. Safety Information

Many remote-control models are equipped with powerful motors and sharp propellers. When using or maintaining models, proceed with caution. When performing assembly or maintenance, make sure to disconnect the power to the model and remove the propellers.

Do not operate the TX15 remote control system under the following conditions:

  • In severe weather or strong windy conditions, such as rain, hail, snow, storms or electromagnetic environments.
  • In any situation where visibility is limited.
  • In areas where people, property, high-voltage power lines, public roads, vehicles or animals may be present.
  • If you feel tired or unwell, or under the influence of drugs or alcohol.
  • If the remote control or model seems to be damaged or not working properly.
  • In areas with high 2.4GHz interference or where 2.4GHz radio is prohibited.
  • When the radio's battery voltage is too low to be used.
  • In areas where local regulations prohibit the use of models.

Disclaimer: For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.

3. Package Contents

The TX15 Radio Controller package typically includes the following items:

  • 1 * TX15 Radio Controller
  • 1 * Signature Carry Case
  • 1 * Short 2-position Latching Shoulder Toggle Switch Assembly
  • 1 * Short 2-position Momentary Shoulder Toggle Switch Assembly
  • 1 * 18650 Battery Tray (Note: 18650 batteries are not included)
  • 1 * USB-C Cable
  • 1 * Screen Protector
  • 1 * 1.5mm Hex Wrench
  • 4 * High Tension Gimbals Springs
  • 2 * Gimbal Stick Set Screw
  • 1 * Stickers Set
  • 1 * User Manual
  • 1 * Inventory Card
Diagram showing the package contents of the Radiomaster TX15 radio controller, including the controller, carry case, switches, battery tray, USB-C cable, screen protector, hex wrench, gimbal springs, set screws, stickers, user manual, and inventory card.
Figure 3.1: Radiomaster TX15 Package Contents

4. Product Features

The Radiomaster TX15 is engineered with advanced features for optimal performance and user experience:

  • Powerful STM32H750 Processor: Our fastest radio ever, delivering lightning-fast response and ultra-smooth performance at 480MHz.
  • Integrated 4GB Flash Memory & External MicroSD Support: Massive storage space for models, scripts, sounds, and themes.
  • Semtech LR1121 Transceiver: Supports both 2.4GHz and Sub-G 900MHz ExpressLRS for rock-solid signal strength and reliability.
  • 3.5-inch High-Visibility Color Touchscreen: 262K color resolution and 600 nits brightness for easy readability indoors and out.
  • V5.0 Hall Gimbals (Standard) / AG02 CNC Hall Gimbal (MAX Version): Experience unmatched precision with low-noise operation. AG02 gimbals feature all-metal construction and adjustable vertical and horizontal travel.
  • Customizable Gimbal Lighting: Programable RGB lighting on the MAX version to personalize your radio's appearance.
  • 6 Programmable RGB Buttons: Provides flexibility in your settings for quick access to functions.
  • Powerful Cooling System: Low-noise, high-output fan and an aluminum heat sink keep your radio cool even on the hottest days.
  • Standard JR Expansion Bay: Provides external RF module expansion.
  • Single USB-C Connector: Multi-functional port for charging, simulator connectivity, and firmware updates.
  • Smart Balance Battery Charging: Prevents overcharging, effectively extending battery life.
  • Foldable Antenna: Compact and easy to transport.
  • Interchangeable Shoulder Switches: Customize your radio setup by swapping shoulder switches.
  • Ergonomic Non-Slip Grip: For confident control and comfortable handling.
  • Built-in Gyro: For advanced control options, allowing you to trigger switches, pan/tilt cameras, or activate telemetry callouts with a simple tilt of your radio.
  • Built-in Microphone: For future feature expansion.
Diagram showing the STM32 H750 processor chip with 480MHz speed and an arrow pointing to 'Our Fastest Radio Ever'.
Figure 4.1: STM32H750 Processor
Diagram showing a 4GB flash memory chip and a MicroSD card slot, indicating massive storage space for models, scripts, sounds, and themes.
Figure 4.2: Integrated 4GB Flash Memory and MicroSD Support
Diagram showing the Semtech LR1121 Transceiver chip, highlighting support for 2.4GHz or Sub-G 900MHz ExpressLRS.
Figure 4.3: Semtech LR1121 Transceiver
Diagram showing the 3.5-inch high-visibility 262K color touchscreen with 600 nits brightness, making it easy to see even under direct sunlight.
Figure 4.4: 3.5-inch High-Visibility Color Touchscreen
Close-up view of the V5.0 Hall Gimbal, highlighting quad precision bearings for unparalleled stick feel.
Figure 4.5: V5.0 Hall Gimbal
Diagram illustrating the vertical and horizontal travel adjustments for the AG02 CNC Hall Gimbal.
Figure 4.6: AG02 CNC Hall Gimbal Adjustments
Diagram showing the powerful cooling system with low-noise, high-output fans and an aluminum heat sink.
Figure 4.7: Powerful Cooling System
Rear view of the TX15 radio controller showing the standard JR expansion bay.
Figure 4.8: Standard JR Expansion Bay
Close-up of the single USB-C port on the TX15, indicating its functions for data transmission, charging, and simulator use.
Figure 4.9: Single USB-C Port Functions
Diagram illustrating the built-in gyro functionality with X-tilt and Y-tilt indicators.
Figure 4.10: Built-in Gyro
Diagram showing the foldable antenna design for easy transport and improved signal strength.
Figure 4.11: Foldable Antenna
Diagram showing the built-in microphone, six customizable RGB buttons, and external module support.
Figure 4.12: Built-in Microphone, RGB Buttons, and External Module Support

5. Setup

5.1 Antenna Installation

WARNING: Install the provided antenna in the top of the radio BEFORE installing batteries and turning on the radio. DO NOT operate the radio without the antenna installed and the internal RF module powered on. Doing so will damage the internal RF module and will not be covered under warranty.

5.2 Battery Installation and Charging

The TX15 has a built-in USB-C charging function for 3.7V lithium batteries. The charging circuit is only designed to charge 2x 3.7V Li-ion 18650 or 2x 3.7V Li-Poly batteries (2s 7.4v Lipo battery pack). The nominal battery voltage is 3.7V, and the charged voltage is 4.2V/Cell.

DO NOT use LiFE battery packs or 18650 lithium-ion batteries with a nominal voltage of 3.6v with a fully charged voltage of 4.10V. Charging the incorrect type of battery may damage the charger or cause a fire.

If using Li-ion, ensure the cells are not protected and are button-top cells.

Please check the voltage and condition of the battery regularly and never charge unattended. Always charge in a safe area away from combustible materials. Refrain from charging if the remote control gets wet or damaged in any way. DO NOT charge with the polarity reversed.

Close-up view of the TX15 battery compartment with a warning label for battery types.
Figure 5.1: Battery Compartment and Warning
Diagram illustrating the smart active balance charging feature for 18650 batteries, preventing overcharging.
Figure 5.2: Smart Active Balance Charging

5.3 Gimbal Adjustments

The TX15 gimbals offer various adjustments for personalized control feel:

  • L-R Mode-1, 2 (Self-Centering): Turn CW to disable self-centering, CCW to enable.
  • Throttle Stick Tension: Turn CW to increase tension, CCW to decrease.
  • Vertical Tension (Up-Down): Turn CW to increase tension, CCW to decrease.
  • Horizontal Tension (Left-Right): Turn CW to increase tension, CCW to decrease.
  • Up Stick Travel (38-54° degrees): Turn CW to decrease travel, CCW to increase.
  • Down Stick Travel (38-54° degrees): Turn CW to decrease travel, CCW to increase.
Diagram of the TX15 radio controller with labels for various gimbal adjustment screws and their functions.
Figure 5.3: Gimbal Adjustment Points

6. Operating Instructions

6.1 Model & Protocol Selection (ExpressLRS)

The TX15 is equipped with a built-in dual-band, dual-frequency ExpressLRS RF module, offering compatibility with a wide range of receivers, specifically 2.4GHz receivers.

To select the appropriate Packet Rate on your TX15 remote control, follow these options based on the receiver type:

  • 50Hz-500Hz 2.4G: For binding with any ExpressLRS 2.4GHz receiver.

6.2 Binding Instructions

  1. TURN OFF the transmitter.
  2. Cycle power to the receiver 3 times; the receiver LED will flash twice, indicating bind mode.
  3. TURN ON the transmitter, press the SYS button and choose ExpressLRS LUA under the TOOLS menu. Scroll to [Bind] and press enter.
  4. The LED on the receiver should now be solid, indicating a successful bind.

6.3 USB-C Functions

The single USB-C port on the TX15 serves multiple purposes:

  • Data Transmission: Connect to a computer for file transfers.
  • Charging: Charge the internal batteries.
  • Simulator: Use the TX15 as a controller for flight simulators.
  • Connectivity and Firmware Updates: Connect for firmware updates and other connectivity needs.
Diagram showing the USB-C port and its functions: USB Joystick (HID), USB Storage (SD), and USB Serial (VCP).
Figure 6.1: USB-C Port Functionality

7. Maintenance

7.1 General Care

  • Keep the radio clean and free from dust and debris.
  • Avoid exposing the radio to extreme temperatures or direct sunlight for prolonged periods.
  • Store the radio in its carry case when not in use to protect it from physical damage.

7.2 Battery Care

Regularly inspect the battery voltage and condition. Always charge in a safe area, away from combustible materials, and never leave charging unattended. If the remote control gets wet or damaged, do not attempt to charge it. Ensure correct polarity when installing batteries.

8. Troubleshooting

8.1 Radio Not Powering On

  • Check battery voltage: Ensure the batteries are sufficiently charged.
  • Battery installation: Verify batteries are correctly installed with proper polarity.
  • Antenna: Confirm the antenna is securely installed. The radio will not operate without it.

8.2 Binding Issues

  • Ensure the receiver is in bind mode (LED flashing twice).
  • Verify the correct packet rate is selected on the TX15.
  • Check for 2.4GHz interference in the operating area.

8.3 Firmware Updates

The TX15 is pre-installed with the most stable firmware at the factory. Only attempt to update the firmware if you are confident in the process. Incorrect firmware updates may cause the remote control to become inoperable.

For firmware updates, refer to the official websites: www.edgetx.org (EdgeTX) and www.expresslrs.org (ExpressLRS).

9. Specifications

FeatureSpecification
ItemTX15/TX15 MAX Radio Controller
Size178*168*81mm
Weight605g (without battery) / 672g MAX (without battery)
FrequencyISM 2.4GHz or Sub-G 900MHz
Internal RF ModuleExpressLRS Single LR1121
Max Current875mA
Voltage Range6.6-8.4V DC
Radio FirmwareEdgeTX (requires version 3.0.0 or later)
Wireless FirmwareExpressLRS
Gimbal SticksM4
GimbalsV5 or AG02 Hall sensor gimbals
Control DistanceMax 2Km (RX dependent)
ChannelsMax 16 channels (RX dependent)
Battery Options7.4V 2-cell Lithium-Polymer or 2x 3.7V 18650 Lithium-Ion batteries (batteries not included)
Display3.5-inch IPS Touchscreen (262k color resolution / 600 nits brightness)
External ModuleJR bay
Upgrade MethodUSB
Wireless CommunicationRF
Battery IncludedNo (Battery Tray Included)
High-concerned chemicalnone
OriginMainland China
Drones Accessories TypeRemote control
CertificationCE, FCC, RoHS
FCC ID2BBP3-TX15

10. User Tips

  • FCC vs. LBT Versions: There are two main certifications for remote controllers: FCC (American radio certification) and LBT (EU radio certification). The LBT version has removed many functions that do not comply with EU regulations, making it less complete than the FCC version. Outside the EU, the FCC version is generally recommended. If you are in the EU, it is better to choose the LBT version. Note that the ELRS LBT (Europe) Version is pre-installed with ExpressLRS CE EU domain LBT FW, limited to 100mw power output.
  • Compatibility: The TX15 is designed to work with various types of aircraft, including airplanes, drones, and other remote-controlled models, thanks to its versatile protocol support (ExpressLRS).
  • Product Quality: Users have reported that the product matches its description and works well.

11. Warranty & Support

If you experience any issues with your TX15 hardware, please retain your proof of purchase for warranty purposes. To initiate a warranty claim or seek repair assistance, follow these steps:

  1. Contact Your Retailer: Contact the retailer where you purchased your TX15 for warranty support.
  2. Visit Our Warranty Support Page: For additional assistance or to contact our support team, visit RadioMaster Warranty Support: www.radiomasterrc.com/contact.

12. Compliance Information

12.1 FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used per the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit that is different from the one to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for assistance.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

12.2 Antenna Separation Distance

When operating your RadioMaster transmitter, please be sure to maintain a separation distance of at least 20 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.

12.3 EU Simple Declaration of Conformity

RadioMaster declares the radio equipment TX15 is in compliance with EU directives Directive 2014/53/EU.

Manufacturer: ShenZhen RadioMaster Co., Ltd, 3th Floor, Yangtian Building, No. 18 Yangtian Road, Xin'an Street, Baoan District, Shenzhen, Guangdong.

13. Product Overview Video

Video: A promotional overview of the Radiomaster TX15 radio controller, showcasing its features and design.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.