Introduction
Thank you for choosing the BaoFeng BF-1909 Walkie Talkie. This high-power, 16-channel UHF two-way radio is designed to provide secure, instant, and reliable communication. Featuring a robust 4800mAh battery and convenient Type-C USB charging, the BF-1909 offers extended standby time and versatile charging options. This manual provides detailed instructions for the proper use, installation, maintenance, and troubleshooting of your device to ensure maximum performance and longevity.
Safety Warnings & Regulations
WARNING! Please read all safety information before operating this device.
EU Regulatory Conformance
This product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU, and other applicable EU regulations (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). It can be operated under 2000m.
WARNING! European Users should note that operation of this unit in Transmit mode requires a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU. This information is applicable to EU countries only.
Compliance with RF Exposure Standards
The radio complies with RF energy exposure standards and guidelines, including:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
RF Exposure Compliance and Control Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany the device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions for RF Exposure:
- Transmit no more than the rated duty factor of 50% of the time. To transmit, press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key.
- Keep the radio unit at least 2.5cm away from the face. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
Precautions for Portable Terminals (Operating Prohibitions):
To protect against property loss, bodily injury or death, observe the following:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres, or other flammable materials.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where wireless communication equipment is completely prohibited.
Important Tips for Product Use:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation. Allow for cooling.
- Handle the product with care.
- Do not disassemble, modify, or repair the product and its accessories without authorization.
Getting Started
1. Package Contents
Before you begin, please verify that all items are present in your package:
- 1 x Radio (BF-1909)
- 1 x Fast desktop charger
- 1 x Antenna
- 1 x Li-Ion battery pack (4800mAh)
- 1 x Wall adaptor
- 1 x Belt clip
- 1 x Sling
- 1 x User's manual (PDF available online)
If any item is missing, please contact your dealer.

Image: BaoFeng BF-1909 Walkie Talkie with key features highlighted.

Image: Key specifications of the BF-1909 including 12W power, 4800mAh battery, and Type-C charging.
2. Radio Overview (Buttons and Controls)

Image: Detailed views of the BF-1909's physical features and controls.
Refer to the diagram for the location of each control:
- Antenna
- LED flashlight
- Status LED
- Power / Volume knob
- Battery release latch
- PTT - Push to talk button
- SK1-Programmable key (flashlight/alarm switch)
- SK2-Programmable Key (Radio/Monitor)
- Accessory jack
- Type-C charging indicator
- V/M-VFO/MR mode key
- A / B select key
- SWEEP key
- MENU Key
- Type-C charging port
- Color LCD
- Speaker
- Microphone
- EXIT Key
- Keypad
3. LCD Display Icons
| Icon | Description | Icon | Description |
|---|---|---|---|
| Mxxx | Memory channel | DW | Dual watch enabled |
| VFO | Frequency Mode | TX | Transmitting |
| VOX | VOX enabled | RX | Receiving |
| CTC | CTCSS enabled | R | Reverse function enabled |
| DCS | DCS enabled | ► | Indicates active band or channel |
| N | Narrowband enabled | +/- | Frequency shift direction if enabled in VFO |
| H/L | Transmit power level Indicator According to Power (High/Low) | Battery level indicator | |
| Squelch Open/ Close Indicator |
4. Status Indications (LED)
| LED Indicator | Radio Status |
|---|---|
| Constant Red | Transmitting |
| Constant Green | Receiving |
5. Main Keypad Controls
- V/M: Short press to switch frequency or channel mode. Press and hold to toggle channel display mode: CH/FREQ/NAME.
- A/B: Short press to toggle upper screen (A)/lower screen (B). Press and hold to switch Double Wait/ Signal Wait/ Dual Watch off modes.
- One-Touch search key: Short press to enter One-Touch search key.
- EXIT: Short press to return to menu or previous menu. Press and hold to enter frequency sweep mode.
- *: Long press to lock or unlock the keypad.
- #z: Short press to enter DTMF dial. Press and hold to scan on and scan off.
- 0 [space]: Press and hold to enter weather switch to select weather channel.
- MENU: Activates the MENU, selects menu items, and confirms parameters.
- ▲/▼ keys: Navigate menu items, adjust frequency/channel, or control scanning direction.
6. Programmed Keys (SK1, SK2)
The [SK1] and [SK2] keys can be programmed for various functions:
| Function | Description |
|---|---|
| None | No Function |
| Torch On/Off | Quick switch torch |
| Power Select | Quickly switch between high, low transmit power |
| Scan On/Off | Quickly switch scanning function on or off |
| VOX On/Off | Quickly switch on/off VOX function |
| Alarm on/off | Quickly establishes an emergency call |
| Radio on/off | Quickly switch on or off the FM radio function |
7. Installation of Accessories
Before attaching or removing the battery, ensure the radio is turned off by turning the power/volume knob counter-clockwise.
7.1 Installing/Removing the Antenna
- Screw the antenna clockwise into the connector on the top of the radio until it is firm.
- To remove, unscrew counter-clockwise.
7.2 Installing the Belt Clip
- Align the grooves of the belt clip with those on the radio and push down until it clicks into place.
- To remove, use a flat-bladed object to press the belt clip tab away from the radio, then slide the clip upward and away.
7.3 Installing the Battery Pack
- Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
- Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.
7.4 Removing the Battery Pack
To remove the battery, press the battery release above the battery pack, as you slide the battery downward.
7.5 Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
8. Charging the Battery
The Li-ion battery pack is not charged at the factory; please charge it before use. For best performance, fully charge/discharge the battery two or three times.
8.1 Charger Supplied
Use only the specified charger provided. Other models may cause explosion or personal injury. If the radio displays low battery, please charge it.
8.2 How to Charge (Desktop Charger)
- Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange.
- Plug the battery or the radio into the charger. The indicator light turns red, indicating charging.
- A full charge takes approximately 2-5 hours. When the lamp lights green, charging is complete.
NOTE:
- If the radio is powered on during charging, the indicator lamp will not turn green to show fully charged status. Turn off the radio for normal operation.
- The radio consumes energy when powered on, preventing the charger from detecting correct battery voltage.
8.3 Using the Type-C USB Charger
The Type-C USB port allows convenient charging of your Li-ion battery pack.

Image: Multiple ways to charge the BF-1909 using Type-C USB.
- Make sure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet, car charger, PC USB, or power bank.
- An empty battery will be fully charged in 4 hours.
- The battery meter on the LCD will move to indicate charging.
Note:
- It is recommended to power OFF your radio while charging.
- For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio connected to the charger.
Operating Instructions
1. Basic Operations
1.1 Powering On/Off the Radio
To turn the unit on, rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash the LCD, then display a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
To turn the unit off, rotate the Volume/Power knob counter-clockwise all the way until you hear a "click".
1.2 Adjusting the Volume
Rotate the Volume/Power knob clockwise to increase volume, and counter-clockwise to decrease volume. Be careful not to turn it too far, as you may inadvertently turn your radio off.
1.3 Main Band/Sub Band Select
In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The selected display becomes the active listening and transmit frequency or channel.
Press and hold [A/B] key to quickly switch Double Wait/ Signal Wait.
1.4 VFO/Channel Switch
Press the [V/M] key to switch between VFO (Frequency) and Channel (MR) display.
- In channel mode (MR), the channel number will be displayed on the left.
- In frequency mode (VFO), the ‘VFO’ will be displayed on the left.
In MR mode, Press and hold [V/M] key to switch the frequency, channel and name display mode of the channel.
1.5 Frequency (VFO) Mode
In VFO mode, you can navigate up and down the band using the ▲/▼ keys, which increment or decrement your frequency according to the set frequency step. You can also input frequencies directly using the numeric keypad with kilohertz accuracy.
WARNING! Transmitting on unauthorized frequencies is illegal and a serious offense. The scanning and receive function of the aviation frequency band (AM108-136MHz) and the police frequency band (350-390MHz) is limited to use in VFO mode and allows manual input of these frequencies. Prohibit use in channel mode.
1.6 Channel (MR) Mode and Channel Selection
There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is generally more practical. Frequency (VFO) mode is useful for experimentation and programming channels into memory.
In Channel (MR) mode, you can navigate up and down the channel using the ▲/▼ keys or the encoder.
Press [V/M] key to switch the radio between VFO and Channel mode, select Channel mode.
Operation 1:
Press the ▲/▼ navigation key to select the channel.
Operation 2:
Input the channel numbers by the keyboard. For example, to switch to channel 12, input [0][1][2].
1.7 Making a Call
- Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with normal tone. The red LED will be on.
- Frequency mode call: Press [V/M] key to switch to frequency mode, input the working frequency, and press and hold the [PTT] key to transmit. The red LED will be on.
- Receive a call: When you release the [PTT] key, you can answer without action. The green LED will be on.
NOTE:
To ensure the best reception volume, keep the distance between the microphone and your mouth at 2.5 cm to 5 cm during transmission.
1.8 Using the Flashlight
You can use the radio's high-intensity LED flashlight in an emergency.
- Press [SK1] key once to turn it on continuously (Always On mode).
- Press [SK1] key again for Strobe Light emergency signal (Strobe emergency mode).
- Press [SK1] key once more to turn the light off.
1.9 Emergency Alert
To activate the emergency alert function, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK1] key to exit.
WARNING: The Emergency Alert feature should only be used in an actual emergency.
1.10 FM Radio
The frequency range for the FM radio is 65-108MHz.
- In frequency or channel mode, press [SK2] key to turn on the radio.
- Select the desired radio frequency with the ▲/▼ keys or input the frequency. Alternatively, press #z to automatically search for a station.
- Press [SK2] key to exit FM radio.
Note:
While listening to the radio, the frequency or channel of A / B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears, the radio will automatically switch back to FM radio mode.
1.11 Monitor
In standby, press and hold the [SK2] key to enter Monitor. This allows monitoring weak signals even if the matched carrier is present but the signaling is too weak. Release [SK2] key to exit.
Note:
If no signal is present, pressing [SK2] will emit noise.
1.12 Keypad Lock
The keypad lock disables all keys except for the three side keys. To enable or disable, press and hold the * key for about two seconds. You can also set the radio to automatically lock the keypad after ten seconds via the menu.
1.13 Frequency Reversal
A short momentary press of the * key enables the reverse function, reversing your transmit and receive frequencies. This is indicated by an "R" on the LCD.
1.14 TX Repeaters Tone
Press [PTT] + [SK2] key to send a 1750Hz repeaters tone. This is useful for communications through repeaters. This function works even if the keypad lock is enabled.
1.15 One Touch Frequency Search
- The radio acts as a receiver. Press and hold the * key; the screen will display “SEARCH SWEEK...”.
- If the unit receives an effective frequency (strongest and stable signal), the received frequency will be displayed, along with CTCSS or DCS values if present.
- Press the [MENU] key to save the Search frequency and CTCSS or DCS to the channel.
Note:
During frequency Search, press the #z key to switch between UHF or VHF bands.
1.16 Weather Radio/Scan Weather Channel
Your radio has a NOAA Weather Radio function to receive weather reports and a NOAA Weather Scan function to scan all 10 NOAA Weather Radio channels.
- To turn on NOAA Weather Scan, press the [OSQL] key for 3 seconds; the radio will go to Weather band mode.
- Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding #z again will stop the scan.
- After stopping NOAA weather scan, manually select the weather channel by pressing the ▲/▼ key.
- To exit Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.
Weather Channel Frequencies and Names:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| Wx-01 | 162.550 | Wx-06 | 162.500 |
| Wx-02 | 162.400 | Wx-07 | 162.525 |
| Wx-03 | 162.475 | Wx-08 | 161.650 |
| Wx-04 | 162.425 | Wx-09 | 161.775 |
| Wx-05 | 162.450 | Wx-10 | 163.275 |
NOTE:
Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
2. Advanced Features
2.1 Working the Menu System
Basic Use with Arrow Keys:
- Press [MENU] to enter the menu.
- Use ▲/▼ keys to navigate between menu items.
- Press [MENU] again to select the desired menu item.
- Use ▲/▼ keys to select the desired parameter.
- To confirm, press [MENU]. To cancel, press [EXIT].
- To exit the menu at any time, press [EXIT].
Using Shortcuts:
Every menu item has a numerical value. You can use these numbers for direct access.
- Press [MENU] to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- Press [MENU] to enter the menu item.
- For parameters, use arrow keys or the numerical keypad for short-cut codes.
- To confirm, press [MENU].
2.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. Dual Watch is inhibited while scanning.
To enable the scanner, press and hold the #z key for about two seconds. Press and hold the #z key again to exit scanning mode.
Scanning Modes:
The scanner can operate in Time, Carrier, or Search mode.
- Setting Scanner Mode: Press [MENU], enter 19, press [MENU], use ▲/▼ keys to select mode, press [MENU] to confirm, then [EXIT].
- Time Operation (TO): Scanner stops on a signal, resumes after a preset time.
- Carrier Operation (CO): Scanner stops on a signal, resumes after the signal disappears.
- Search Operation (SE): Scanner stops on a signal, requires pressing #z to resume.
Frequency Scanning:
- In frequency mode, press #z for more than 2 seconds to start scanning.
- Change scanning direction with ▲/▼ keys.
- Press #z to stop scanning.
Channel Scanning:
- In channels mode, press #z for more than 2 seconds to start scanning.
- Change scanning direction with ▲/▼ keys.
- Press #z to stop scanning.
Scan CTCSS:
- In standby mode, press [MENU] [1][6]. "Scan CTCSS" appears.
- Press [MENU] to start scanning CTCSS tones.
Note:
This function cannot be activated in Channel mode. Scanning starts only when the receiving band detects a signal.
Scan DCS:
- In standby mode, press [MENU] [1][7]. "Scan DCS" appears.
- Press [MENU] to start scanning DCS codes.
Note:
This function cannot be activated in Channel mode. Scanning starts only when the receiving band detects a signal.
2.3 Manual Programming (Channels Memory)
Memory channels store commonly used frequencies. The radio has 999 memory channels, each capable of holding receive/transmit frequencies, power, signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.
Frequency Mode (VFO)
Used for temporary frequency assignments or quick field programming.
Channel Mode (MR)
Used for selecting preprogrammed channels.
Example 1: Programming a Channel Repeater Offset with CTCSS Tone
To program a new memory in Channel 10 with RX = 432.55000 MHz, TX = 437.55000 MHz (a +5 Offset), and TX CTCSS tone 123.0:
- Press [EXIT] to switch between menus.
- Press [V/M] to set the radio to VFO mode.
- Enter [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes Prior Data in channel 10).
- Enter [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone).
- Enter RX frequency (e.g., 43255000).
- Enter [MENU] [1][3] [MENU] [1][0] [MENU] (Enters desired channel 10, RX has been added).
- Enter TX frequency (e.g., 43755000).
- Enter [MENU] [1][3] [MENU] [1][0] [MENU] (Enters same channel 10, TX has been added).
- Press [V/M] to return to MR mode.
Example 2: Programming a Simplex Channel with CTCSS Tone
To program a new memory in Channel 10 with RX = 432.6625 MHz and TX CTCSS tone 123.0:
- Press [EXIT] to switch between menus.
- Press [V/M] to set the radio to VFO mode.
- Enter [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes Prior Data in channel 10).
- Enter [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone).
- Enter RX frequency (e.g., 43266250).
- Enter [MENU] [1][3] [MENU] [1][0] [MENU] (Enters desired channel 10, Channel has been added).
- Press [V/M] to return to MR mode.
2.4 Repeaters Programming
These instructions assume you know your repeater's transmit and receive frequencies and are authorized to use them.
- Press [V/M] to set the radio to VFO mode.
- Use the numeric keypad to enter the repeater's output (your receiving) frequency.
- Press [MENU].
- Enter [1][2] for frequency offset.
- Press [MENU] to select.
- Use the numerical keypad to enter the specified frequency offset (see "12 OFFSET - Frequency shift amount" in the full manual).
- Press [MENU] to confirm and save.
- Enter [1][1] for offset direction.
- Use the ▲/▼ keys to select + (positive) or - (negative) offset.
- Press [MENU] to confirm and save.
- Optional: Save to memory (see Manual Programming) and/or set up CTCSS (see CTCSS details in the full manual).
- Press [EXIT] to exit the menu.
Note:
If you experience problems connecting to the repeater, check your settings or repeat the procedure. Some Amateur Radio repeaters use a 1750Hz tone burst to open up. If you are still unable to connect, contact the radio system administrator or your local amateur radio club.
2.5 VOX (Voice Activated Transmit)
VOX allows hands-free conversations. Speak into the microphone, and communication will activate automatically.
Enabling VOX:
In standby mode, press [MENU] + 25. "VOX Switch" appears. Press [MENU], use ▲/▼ keys to turn ON/OFF VOX, then [MENU] to confirm.
Adjusting VOX Level:
In standby mode, press [MENU] + 26. "VOX Level" appears. Press [MENU], use ▲/▼ keys to select VOX level (1-9), then [MENU] to confirm. Press [EXIT] to return to standby.
Note:
Level 1 is the least sensitive, level 9 is the most sensitive. VOX is not enabled in Scan or FM Radio mode.
2.6 Dual Watch
Dual Watch allows monitoring two channels simultaneously. The radio features Dual Watch functionality (single receiver) and can lock the transmit frequency to one of the two monitored channels.
Enabling or Disabling Dual Watch Mode:
- Press [MENU].
- Enter 38 for Dual Watch.
- Press [MENU] to select.
- Use ▲/▼ keys to select Double Wait/ Signal Wait/ OFF.
- Press [MENU] to confirm.
- Press [EXIT] to exit.
2.7 Stopwatch Timer
In standby mode, press [MENU] + 57. "STOP WATCH" appears. Press [MENU] to start/restart counting. To exit, stop counting first, then press [EXIT].
2.8 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method used for automation systems and remote control, common in amateur radio repeaters.
DTMF Frequencies and Corresponding Codes:
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
The numerical keys, *, and #z correspond to DTMF codes. A, B, C, and D codes are on [MENU], ▲/▼, and [EXIT] keys respectively. To send DTMF codes, press the key(s) while holding down the PTT key. This works even with keypad lock enabled.
2.9 Customization
The radio allows customization of visual and audible features.
Display Backlight (ABR) - MENU 51:
In standby mode, press [MENU] + 51. "ABR" appears. Press [MENU], use ▲/▼ keys to select ON/5sec/10sec/15sec/20sec/30sec/60sec, then [MENU] to confirm. Press [EXIT] to return.
Beep Prompt (BEEP) - MENU 32:
Enables a beep tone every time a key is pressed. In standby mode, press [MENU] + 32. "BEEP PROMPT" appears. Press [MENU], use ▲/▼ keys to turn ON/OFF, then [MENU] to confirm. Press [EXIT] to return.
Voice Function (VOICE) - MENU 30:
In standby mode, press [MENU] + 30. "VOICE" appears. Press [MENU], use ▲/▼ keys to select OFF/ON, then [MENU] to confirm. Press [EXIT] to return.
Language of the MENU (LANGUAGE) - MENU 29:
In standby mode, press [MENU] + 29. "LANGUAGE" appears. Select English or Chinese.
Working Mode (MDF-A) - MENU 39:
The radio has four working modes: Frequency (FREQ), Channel (CH), Channel Name (NAME). To shift, in standby mode, press [MENU] + 39, select the desired mode with ▲/▼ keys, then [MENU] to confirm.
Roger Beep (ROGER) - MENU 33:
Enables/disables an end-of-transmission tone. In standby mode, press [MENU] + 33. "ROGER" appears. Press [MENU], use ▲/▼ keys to select OFF/ON, then [MENU] to confirm. Press [EXIT] to return.
Power On Message (POWER ON MSG) - MENU 40:
Customizes the welcome message on display. Options: VOLTAGE, MESSAGE, LOGO. In standby mode, press [MENU] + 40. "POWER ON MSG" appears. Press [MENU], use ▲/▼ keys to select option, then [MENU] to confirm. Press [EXIT] to return.
Power On Password (Power On PWD) - MENU 37:
Requests a password when the radio is turned on. In standby mode, press [MENU] + 37. "POWER ON PWD" appears. Press [MENU], use ▲/▼ keys to enable/disable, then [MENU] to confirm. Press [EXIT] to return. Default password is 000000.
Reset - MENU 56:
Two reset modes: VFO and ALL.
- Reset VFO: Resets all settings except channels to default. In standby mode, press [MENU] + 56. "RESET" appears. Press [MENU], use ▲/▼ keys to select VFO, then [MENU] to confirm. "Sure to reset?" appears. Press [MENU] again to confirm. The transceiver will turn off and reboot.
- Reset ALL: Resets all settings to default. In standby mode, press [MENU] + 56. "RESET" appears. Press [MENU], use ▲/▼ keys to select ALL, then [MENU] to confirm. "Sure to reset?" appears. Press [MENU] again to confirm. The transceiver will turn off and reboot.
Maintenance
1. Battery Maintenance Instructions
To prolong battery life and ensure normal operation:
- Clean accumulated dust on charging connectors regularly with a clean, dry cloth.
- Charge the battery between 5°C~40°C (40°F - 105°F).
- Turn off the radio to ensure a full charge when charging a battery attached to the product.
- Do not remove the battery or unplug the power cord during charging.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight or other heating sources.
- Do not squeeze, penetrate, or remove the housing of the battery.
2. Battery Storage
- Store the battery at 80% discharged.
- Keep it in a low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- Do not short circuit the battery terminals.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
3. General Care
- Clean the radio's exterior with a soft, damp cloth. Avoid harsh chemicals.
- Ensure all ports are covered when not in use to prevent dust and moisture ingress.
Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| Cannot turn on the radio. | Battery improperly installed, power run out, poor contact, or low voltage. | Remove/reattach battery, recharge/replace battery, clean contacts. |
| Weak or intermittent voice during receiving. | Volume low, loose/incorrect antenna, blocked speaker. | Increase volume, reattach antenna, clean speaker. |
| Cannot communicate with other group members. | Incorrect frequency/signaling type, too far, interrupted by same frequency. | Verify TX/RX frequency/signaling, move closer, change frequency/adjust squelch. |
| Hear unknown voices or noise. | Radio in analog mode with no signaling. | Request dealer to set signaling. |
| Unable to hear anyone due to too much noise/hiss. | Too far, unfavorable position (buildings/underground), external disturbance. | Move closer, move to open area, restart radio, stay away from interference. |
| Radio keeps transmitting. | VOX enabled or headset not in place. | Turn off VOX, check headset. |
NOTE: If the above solutions cannot fix your problems, or you have other queries, please contact your dealer for more technical support.
Technical Specifications
| Feature | Specification |
|---|---|
| Brand Name | BAOFENG |
| Model Number | BF-1909 |
| Item Type | Mobile Radio |
| Tuner Technology | UHF |
| Frequency Range | 400-470MHz (UHF1: 400-520MHz (RX&TX); UHF2: 350-390MHz (RX)) |
| Other Frequency Bands | FM radio 76-108 MHz; AM aviation 108-136MHz (RX); VHF1: 136-174MHz (RX&TX); VHF2: 220-260MHz (RX&TX) |
| Storage Channel | 16 (Up to 999 memory channels) |
| Maximum Range | 5km-10km |
| Output Power(w) | 10w-25w (12W High Power) |
| Battery Capacity(mAh) | 4800mAh (Li-Ion 7.4V/1400 mAh BL-K6) |
| Is Batteries Included | Yes |
| Display Screen | No (Color LCD for menu operation) |
| Dimensions | 140*55*35mm (64x121x35mm LxAxP) |
| Weight | 240g (approx. 0.713kg packaged) |
| Waterproof | IP45 |
| Material | Plastic (ABS shell) |
| Operating Temperature | -20℃~+60℃ (-10°C to +45°C) |
| Working Mode | Monoband/Dualband (Same frequency simplex or different frequency simplex) |
| Modulation | F3E(FM) |
| Max. frequency deviation | ≤ ±5KHz |
| Spurious radiation | < -60dB |
| Frequency stability | ±2.5 ppm |
| Rx sensitivity | < 0.15μV (< 0.2uV) |
| Audio output power | ≥ 400MW (≥ 500mW) |
| Emission current | ≤2.6A |
| Stand-by current | 72mA (average 36mA in power-saving state) |
| Certification | CE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee |
WARNING: Direct plug-in AC/DC power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.
Specifications are subject to change without notice.
User Tips
- For optimal battery life, remember to fully charge and discharge the battery 2-3 times upon first use or after extended storage.
- Always turn off the radio when charging to ensure a complete and accurate charge indication.
- Utilize the Type-C charging port for convenient charging from various sources like power banks or car chargers.
- When operating in areas with potential interference, adjust the squelch level to filter out unwanted noise and improve call quality.
- Keep the radio at least 2.5 cm from your face during transmission to comply with RF exposure guidelines.
Warranty & Support
For any technical support, warranty claims, or service inquiries, please contact your authorized dealer or the point of purchase.
A comprehensive user manual in PDF format is available for download. You can view it here.