Introduction
This manual provides detailed instructions for the DAKEFPV F405 V3 Flight Controller and the accompanying 12S 100A/120A 4-in-1 Electronic Speed Controller (ESC) Stack. Designed for FPV freestyle drones and other multi-rotor or fixed-wing aircraft, this stack offers high performance and versatility. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.
Package Contents
Depending on your purchase option, your package will contain the following items:
Option 1: DAKEFPV F405 120A 30x30 STACK

Image: Package contents for the F405 Flight Controller and 120A 4-in-1 ESC Stack.
- DAKEFPV F405 Flight Controller x 1
- DAKEFPV BLS 120A 4-in-1 ESC x 1
- 35V 1000uF Low ESR Capacitor x 1
- M3 Nylon Nut x 5
- M3 Silicone O-Ring x 5
- M3*8mm Silicone Grommets (for FC) x 1
- M3*8.1mm Silicone Grommets (for ESC) x 1
- SH 1.0mm 25mm-length 8-pin Cable (for FC-ESC connection) x 1
- SH 1.0mm 75mm-length 8-pin Cable x 1
- M3*30mm Inner-hexagon Screws x 5
- GPS 6-pin cable, Analog VTX 6-pin cable, dual-camera 6-pin cable x 1
- XT60 Power Cable (70mm) x 1
Note: When the ESC tail faces the drone's front, use the appropriate 8-pin cable for FC and ESC connection; both ends plug interchangeably.
Option 2: DAKEFPV F405 30x30 FC (Flight Controller only)

Image: Package contents for the F405 Flight Controller only.
- DAKEFPV F405 Flight Controller x 1
- Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 5
- FC 12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
- GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable
Specifications
DAKEFPV F405 Flight Controller
| Feature | Specification |
|---|---|
| Main Control Chip | STM32F405 |
| Gyroscope | ICM42688P |
| USB Interface | Type-C |
| Barometer | Built-in |
| OSD Chip | AT7456E |
| Bluetooth BLE | No |
| WiFi | Not supported |
| Input Voltage | 3-8S Lipo |
| UART Ports | 8 groups |
| Buzzer Support | BZ+, BZ- connected to 5V buzzer |
| SmartPort/FPort | Not supported |
| Supported Firmware | BetaFlight (default), Ardupilot, INAV |
| Firmware Target Name | DAKEFPVF405 |
| Mounting Holes | 30.5 x 30.5 mm (4mm diameter) |
| Dimensions | 36 x 36 x 8 mm |
| Weight | 10.5g |
| Onboard Flash | 16MB |
| BEC Output | 12V 3A + 5V 3A dual independent BEC |
| Motor/Servo Support | Supports 8 motors and 4 servos |
| DJI Air Unit Compatibility | Direct plug interface for DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 |
DAKE 12S 100A/120A 4-in-1 ESC
| Feature | Specification |
|---|---|
| Product Name | DAKE 12S 120A 4-in-1 ESC |
| Firmware | BLHeli_S / BLHeli_32 (BLJay) |
| Input Voltage | 3-12S Lipo |
| Continuous Current | 120A x 4 |
| Max Current (10s) | 125A x 4 |
| Built-in TVS Diode | Yes |
| External Capacitor | 1000uF Low ESR (included) |
| ESC/Motor Protocol | Dshot300/Dshot600/PWM/Bi-directional Dshot |
| Output Voltage | VBAT |
| Current Meter | Supports (Scale=400, Offset=0) |
| Telemetry | Not supported |
| Mounting Holes | 30.5 x 30.5 mm (4mm diameter) |
| Dimensions | 45.4 x 42.8 x 6.5 mm |
| Weight | 23.5g |
Physical Dimensions

Image: Detailed dimensions for the F405 Flight Controller and 4-in-1 ESC.
- Flight Controller: 36 x 36 x 8.0 mm (L x W x H)
- ESC: 45.4 x 42.8 x 6.5 mm (L x W x H)
- Stack Height: 15.8 mm
- Mounting Holes: 30.5 x 30.5 mm (M3)
Setup and Installation
Stack Installation Notes

Image: Diagram illustrating the importance of leaving sufficient space during stack installation.
When installing your flight controller and ESC stack, adhere to the standard mounting method. The orientation of the gyroscope and motor sequence can be adjusted through software settings (e.g., Betaflight Configurator).
Important: If you opt for an inverted mounting, be extra careful about the space between the frame, the Flight Controller (FC), and the Electronic Speed Controller (ESC). It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Any damage resulting from improper installation of this nature is not covered under warranty.
To prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package.
Wiring Diagram

Image: Comprehensive wiring diagram showing connections for the Flight Controller, ESC, motors, receiver, GPS, VTX, camera, and LED.
The FC and ESC can also be connected via direct soldering if preferred, following the pin definitions below.
Flight Controller Layout and Pinouts

Image: Detailed layout and pinout diagram for the DAKEFPV F405 Flight Controller.
Refer to the diagram above for specific pin assignments including OSD, RX/TX ports, motor outputs (M1-M8), battery voltage (BAT), ground (GND), current sensor (CUR), camera inputs (CAM1, CAM2), 12V/5V outputs, 3V3, DIO, CLK, SDA, SCL, ELRS, and Gyro connections.
ESC Layout and Connections

Image: Diagram showing motor connections (MOTOR 1-4), battery pads (BAT+, BAT-), and capacitor pin holes on the BLS 120A 4-in-1 ESC.
Connect your motors to the designated M1-M4 pads on the ESC. Ensure correct motor rotation direction is configured in your flight controller software (e.g., Betaflight Configurator).
Receiver Connections
SBUS Receiver: When using an SBUS receiver, connect its SBUS signal wire to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).
Important for DJI Air Unit users with SBUS: If you are also using a DJI Air Unit (O3/Link/Vista/Air Unit V1), you must disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized. Use tweezers to carefully remove the SBUS wire from the 6-pin harness connector or cut and insulate it.

Image: Illustration of disconnecting the SBUS wire from the DJI Air Unit harness for proper external SBUS receiver function.
ELRS Receiver: We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller.
Important for DJI Air Unit users with ELRS: If using a DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly. In this case, you need to disconnect the SBUS signal wire from the Air Unit harness. Use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

Image: Diagram illustrating ELRS receiver connection to T2/R2 and the necessary SBUS wire disconnection when using a DJI Air Unit.
DJI Air Unit Connections
The F405 Flight Controller features a direct plug interface for DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, eliminating the need for wire changes.
- DJI O3 Air Unit: Use the 6-pin cable that comes with the O3 Air Unit.
- RunCam Link/Caddx Vista Air Unit: Use the 6-pin cable that comes with the H743 stack (refer to accessory No.11 in the package section).

Image: Diagram showing cable connection for DJI Air Unit V1.
Operating Instructions
Firmware Flashing (DFU Mode)
To enter DFU (Device Firmware Upgrade) mode for firmware flashing (e.g., Betaflight, Ardupilot, INAV), press and hold the BOOT button on the Flight Controller while connecting it to your computer via USB. This is typically used for initial setup or troubleshooting firmware issues.
Battery Level Indicator
The flight controller features a 4-level battery capacity indicator. Once the battery is connected, you can instantly see the battery level, eliminating the need for an external LiPo checker.

Image: Diagram showing the 4-level battery capacity indicator on the Flight Controller.
LED Light Bar Control
The LED pads at the corners of the flight controller allow you to connect and control external LED light strips. A single press of the BOOT button will cycle through different lighting modes. To activate the onboard LED light effect control mode, long-press the BOOT button. Subsequent short presses will toggle between various preset light effects.

Image: Diagram highlighting the LED light bar pads and explaining control via the BOOT button.
Motor Support
The flight controller supports up to 8 motors, making it suitable for X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors. Ensure your motor configuration is correctly set in your flight control software.

Image: Diagram indicating motor output pads M1-M6 on the Flight Controller.
Maintenance
- Regular Inspection: Periodically inspect all solder joints and connections for any signs of damage, corrosion, or loose connections.
- Cleaning: Keep the flight controller and ESC free from dust, dirt, and moisture. Use a soft brush or compressed air for cleaning. Avoid using liquids directly on the electronics.
- Firmware Updates: Check the official DAKEFPV website or relevant flight control software (Betaflight, Ardupilot, INAV) for the latest firmware updates. Keeping your firmware updated can improve performance and fix bugs.
- Capacitor Check: Ensure the Low ESR capacitor is securely connected and shows no signs of damage. This capacitor is crucial for filtering voltage spikes.
Troubleshooting
- No Power/Intermittent Power:
- Check all power connections, especially the XT60 and battery leads.
- Ensure the Low ESR capacitor is correctly installed and not damaged.
- Verify battery voltage is within the supported 3-12S range.
- Flight Controller Not Recognized by PC (DFU Mode):
- Ensure you are pressing and holding the BOOT button while plugging in the USB cable.
- Try a different USB cable or port.
- Install necessary DFU drivers for your operating system.
- SBUS Receiver Not Working with DJI Air Unit:
- As noted in the setup section, disconnect the SBUS signal wire from the DJI Air Unit harness. This is a common issue that prevents the external SBUS receiver from being recognized.
- ELRS Receiver Issues with DJI Air Unit:
- Similar to SBUS, if you experience issues with ELRS when a DJI Air Unit is connected, try disconnecting the SBUS signal wire from the Air Unit harness.
- Motor Not Spinning/Incorrect Direction:
- Check motor wiring to the ESC.
- Verify motor direction in your flight control software (e.g., Betaflight Configurator).
- Ensure ESC calibration is performed if required by your firmware.
- Unstable Flight/Gyro Issues:
- Ensure the FC is securely mounted and isolated from vibrations using the provided grommets.
- Check for any physical damage to the gyroscope.
- Verify firmware settings related to PID tuning and gyro filtering.
- Black Box Data Retrieval:
- The built-in 16MB flash continuously records flight status. In case of a crash or power outage, the data can still be retrieved for accident analysis using appropriate software tools.
User Tips
- Pre-flight Checks: Always perform thorough pre-flight checks, including motor direction, control surface response, and battery voltage, before each flight.
- Soldering Best Practices: Use a good quality soldering iron and lead-free solder. Ensure clean, strong solder joints to prevent intermittent connections or shorts.
- Cable Management: Secure all cables to prevent them from interfering with propellers or other moving parts, and to reduce vibration.
- Software Configuration: Familiarize yourself with the chosen flight control software (Betaflight, Ardupilot, INAV) and its configurator. Proper configuration is key to optimal performance.
- Heat Management: While the ESC has an aluminum alloy heat sink, ensure adequate airflow around the stack, especially during demanding flights, to prevent overheating.
Warranty and Support
DAKEFPV products are designed for enthusiasts and require careful installation and handling. Please note the following regarding warranty:
- Any damage resulting from improper installation, such as short circuits due to incorrect silicon pad placement or contact between the USB interface and ESC, is not covered under warranty.
- For technical support, firmware updates, or further assistance, please refer to the official DAKEFPV website or community forums related to Betaflight, Ardupilot, or INAV.