1. Introduction
The NISSEI DG-503MAX is a high-performance digital SWR/Watt meter designed for amateur radio applications. It provides accurate measurements of Forward Power (FWD), Reflected Power (REF), and Standing Wave Ratio (SWR) across a broad frequency range from 1.6MHz to 525MHz. This device supports various modulation modes including CW, FM, SSB, AM, and DMR, making it a versatile tool for optimizing your radio setup. Its large 3.5-inch LCD display with backlight ensures easy readability of measurements.
2. Key Features
- Large 3.5-inch LCD display for clear and easy reading.
- Simultaneous display of Forward Power, Reflected Power, and VSWR ratio.
- Selectable measurement modes for DMR (TDMA), AM, and SSB.
- LCD backlight for enhanced visibility in various lighting conditions.
- Convenient control layout for straightforward operation.
- Wide frequency range: 1.6-525MHz.
- Power measuring range: 0-200W.
- One-click switching between HF mode and V/UHF mode.
- Suitable for shortwave radio stations, UV segment car-mounted radios, and handheld walkie-talkies.
3. Package Contents
Please check the box for the following items:
- 1 x NISSEI DG-503MAX Digital SWR Meter
- 1 x DC 12V Power Cable
- 1 x User Manual
4. Specifications
| Parameter | Value |
|---|---|
| Model | DG-503MAX |
| Frequency Range | 1.6-525MHz |
| Power Measuring Range | 0-200W |
| Impedance | 50 ohms |
| Distortion | <= 0.1dB |
| Display Type | 3.5-inch LCD |
| Interface | SO-239 (M female connector) |
| Dimensions (L x W x H) | 140 x 84 x 122mm |
| Net Weight | 755g |
| Warranty | 1 Year |
5. Device Overview
6. Setup Instructions
Follow these steps to properly set up your NISSEI DG-503MAX SWR Meter:
- Power Connection: Connect the provided DC 12V power cable to the 12V DC input jack on the rear panel of the SWR meter (refer to Figure 2). Connect the other end to a suitable 12V DC power source.
- Antenna and Transceiver Connections:
- Identify the correct SO-239 connectors on the rear panel based on your operating frequency band (HF or V.UHF). Refer to Figure 3 for frequency labels.
- Connect your transceiver's output to the 'TX' connector using a suitable coaxial cable.
- Connect your antenna to the 'ANT' connector using a suitable coaxial cable.
- Band Selection: Use the 'HF/V.UHF' switch on the front panel to select the appropriate frequency band for your operation. Ensure this matches the connectors you used on the rear.
- Power On: Press the red 'POWER' button on the front panel to turn on the device. The LCD display should illuminate.
7. Operating Instructions
Once the SWR meter is set up, follow these steps for operation:
- Select Frequency Band: Ensure the 'HF/V.UHF' switch on the front panel is set to the correct band for your current operation.
- Transmit: Briefly transmit a low-power signal from your transceiver.
- Read Measurements: The 3.5-inch LCD display will show three key values:
- **FWD (Forward Power):** The power transmitted from your transceiver.
- **REF (Reflected Power):** The power reflected back from the antenna system.
- **SWR (Standing Wave Ratio):** The ratio indicating the impedance match between your transceiver and antenna. A lower SWR (ideally 1.0:1) indicates a better match.
- Adjust Antenna (if necessary): If your SWR reading is high (e.g., above 1.5:1 or 2.0:1, depending on your radio's tolerance), adjust your antenna or antenna tuner to minimize the SWR. Observe the display for real-time feedback.
- Select Measurement Mode (DG-503MAX specific): The DG-503MAX model allows selection for DMR (TDMA), AM, and SSB modes. Consult the device's internal menu or specific buttons (if present, not explicitly detailed in provided data) to switch between these modes for accurate readings with different modulation types.
- Power Off: After use, press the 'POWER' button to turn off the device.
8. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the device. Do not use liquid cleaners or solvents, as they may damage the finish or internal components.
- Storage: Store the SWR meter in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
- Connections: Periodically check all coaxial and power connections to ensure they are secure and free from corrosion.
- Avoid Impact: Protect the device from drops and impacts, especially the LCD display.
9. Troubleshooting
- No Display/Device Not Powering On:
- Check the 12V DC power connection and ensure the power source is active.
- Verify the power cable is not damaged.
- Ensure the 'POWER' button is fully pressed.
- Inaccurate Readings:
- Confirm that the 'HF/V.UHF' switch is set to the correct band corresponding to your operating frequency.
- Ensure all coaxial cables are properly connected and in good condition.
- Verify that the connectors used on the rear panel match the selected frequency band (refer to Figure 3).
- Check the transceiver's output power setting.
- High SWR Readings:
- This typically indicates an impedance mismatch with your antenna system. Inspect your antenna, feedline, and any antenna tuners for issues.
- Ensure the antenna is designed for the frequency you are operating on.
10. User Tips
- Always start with low power when testing SWR to prevent damage to your equipment.
- For the most accurate SWR readings, perform measurements as close to the antenna as possible.
- Regularly check your SWR, especially after making changes to your antenna system or operating frequency.
- Keep the display clean for optimal readability.
11. Warranty and Support
The NISSEI DG-503MAX Digital SWR Meter comes with a 1-year warranty from the date of purchase, covering manufacturing defects. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer directly.
Contact Information:
Shenzhen Tianzhongtian Trading Co.,Ltd
WhatsApp/Tel/Wechat: +86 19902906050
Web: http://www.thanksbuyer.com
Address: Room 303 Building 2, Youpin Cultural and Creative Park, Zhangkeng, Minzhi Street, Longhua District, 518131, Shenzhen, China (Mainland)



