Hcalory TB2-SE, TB2-P

Contents

Hcalory Parking Heater User Manual

Models: TB2-SE, TB2-P

Smart Heat, Your Control

1. Introduction

Thank you for choosing the Hcalory Diesel Air Car Parking Heater. This manual provides essential information for the safe and efficient operation of your device. Please read it carefully before use to understand the function and operation requirements of the product.

1.1 Product Overview

Diesel heaters are on-board heating devices that are independent of the automobile engine, and have their own fuel lines, circuits, combustion heating devices, and control devices. Originally, these machines were often used to preheat the engine and cab of a car parked in a cold environment in winter, as a way to eliminate cold start wear and tear of the car. Now, diesel heaters have a wider range of uses, serving as space heating equipment in tents, indoors, and RVs, making users' living and traveling more comfortable.

1.2 Explanation of Principles (Heat Source, Heating, Control)

1.2.1 Heat Source:

After the equipment is started, the ignition plug heats up for 1-3 minutes. The fan then delivers air to the combustion chamber, and the diesel pump injects diesel into the combustion chamber. The atomized diesel mixes with air and ignites upon contact with the high-temperature ignition plug, generating significant heat. The high-temperature exhaust gases are discharged through the exhaust gas outlet below.

1.2.2 Heating:

The heat generated in the combustion chamber is quickly transferred to the aluminum heat exchanger and dissipated into the warm air duct via the aluminum fins. An external fan blows air around the heat exchanger, and the heated air is then expelled from the warm air outlet.

1.2.3 Control:

The controller is embedded in the device. Users can control the device via the connected switch panel, checking its running status, adjusting settings, and scheduling operations. Remote control is also possible using the provided remote or the Hcalory mobile application.

2. Safety Instructions (Read Before Use)

Read all safety warnings, instructions, illustrations, and instruction manuals provided with this diesel heater. Failure to follow all of the instructions below may result in electric shock, fire, or serious injury.

  1. Do not replace important parts of the diesel heater without authorization. If repair or replacement parts are needed, contact customer service for correct product specifications and model. Using incorrect specifications may damage the combustion system.
  2. The heater must not be used in places where flammable vapors or dust may be formed, such as:
    • Fuel depots, carbon depots, timber depots, granaries, and similar locations.
    • Diesel/gas stations. Keep away from fuel tanks, compression tanks, fire extinguishers, clothing, and other flammable items.
  3. Use the machine safely and understand its hazards. Children are not allowed to play with this machine. Cleaning and maintenance must not be carried out unsupervised by children.
  4. Do not go near flammable materials (the exhaust pipe operates at very high temperatures)! During installation, use, maintenance, and scrapping, ensure no flammable or explosive materials are around the exhaust pipe to avoid ignition and fire.
  5. Keep ventilation and keep the pipes open. When installing, using, maintaining, and disposing of this equipment, ensure a ventilated area to prevent carbon monoxide poisoning. Place the metal exhaust pipe outdoors to prevent exhaust gases from entering the room.
  6. Do not use the heater in an enclosed or unventilated place.
  7. The heater should be turned off when adding diesel.
  8. Do not cut off the power supply directly! After turning off the heating program, the equipment needs 3-5 minutes for extinguishing and cooling. Do not cut off power during this process. (Cutting off power directly may cause abnormal shutdown and negatively impact subsequent starts).
  9. If the fuel system of the fuel heater is leaking, contact after-sales personnel for parts and repair guidance.
  10. Place the exhaust port outdoors to prevent exhaust gases from entering the room.
  11. During operation, it is strictly forbidden to directly cut off the power supply to stop the heater.
  12. When installing the pipeline, ensure it is unblocked and not squeezed or blocked.
  13. After overheating protection, the machine stops heating. Do not turn off the power. Once the machine has cooled down naturally and is shut down, it can be restarted.
  14. Do not disconnect the power supply immediately after turning off the machine. It takes 3-5 minutes for the machine to stop working completely.
  15. The first 3-5 minutes after turning on the machine is the preheating and ignition stage. During this time, the ignition plug, oil pump, and fan operate according to a preset program. Hot air will be discharged from the warm air duct after a few minutes; please be patient.
  16. When starting, the ignition plug requires a relatively large current. An adapter with 12V voltage and 12A or greater current is needed as a power supply. After successful ignition, the equipment only needs 1-4A to work continuously.

Usage Guidelines:

  • It is forbidden to use the product in high humidity, conductive dust, flammable and explosive gas, dust, materials, corrosive media, strong light, strong magnetic field, high voltage, and high current equipment.
  • Power supply voltage range: DC 24V controller is applicable to (18~32)V; DC12V controller is applicable to (9~16)V; controllers with different voltages are not universal and must not be used beyond the applicable voltage range.
  • The 5kW controller can only be used on a 5kW machine; the 2kW controller can only be used on a 2kW machine.
  • If the controller or external device is damaged, you must use the same model and parameter device and have it replaced by a professional.
  • It is forbidden to open the controller case without permission.
  • The equipment must be installed strictly in accordance with the requirements and must be used under safe conditions.
  • The company is not responsible for any loss or liability caused by wrong connection, short circuit or damage of external devices or lines.
  • When the machine body is at high temperature and the fan cannot operate normally, the machine body must be cooled down quickly. Blow cold air from the combustion-supporting air inlet to cool the machine body down to below 80 °C. Prevent high temperature from scalding parts or causing fire.
  • When the equipment is heated, it is necessary to ensure that all air ducts are unobstructed and that there is no folding, compression or blockage in the pipes, in order to effectively ensure the heating efficiency and normal operation of the equipment. If the passages are not unobstructed, it will cause the machine to be overheated, reduce the heating efficiency, shorten the service life of the equipment or damage the equipment. Only by using fuel that meets the standards can the normal use and service life of the equipment be ensured.
  • This device can adjust the oil pump frequency by entering the password. This requires professionals to operate in a safe environment.
  • Our company is not responsible for any loss or liability caused by failure to install and use the product in accordance with the above provisions.
  • The ignition point of cotton and sponge is 150°C, the ignition point of paper is 130°C, the ignition point of cloth is 270°C, and the ignition point of diesel is 220°C. The hot air outlet can be higher than 150°C, and the exhaust pipe outlet can be higher than 270°C.

3. Components and Package Contents

The Hcalory Parking Heater comes with the following components:

Package Accessories List
Figure 3.1: Package Accessories List

Package Contents (TB2-P Model):

  • 1 x Air Diesel Heater (Host)
  • 1 x Wireless Temperature Sensing Remote
  • 1 x LCD Switch
  • 1 x Manual
  • 1 x AC Power Adapter
  • 1 x Wire harness
  • 1 x Exhaust Silencer
  • 1 x Exhaust pipe
  • 1 x Intake pipe
  • 1 x Air Outlet Pipe
  • 1 x Air Filter
  • 1 x Vents
  • 1 x Fixture Accessories set
  • 1 x Controller extension cord

Package Contents (TB2-SE Model):

  • 1 x Air Diesel Heater (Host)
  • 1 x LCD Switch
  • 1 x Remote control
  • 1 x Manual
  • 1 x AC Power Adapter
  • 1 x Wire harness
  • 1 x Exhaust Silencer
  • 1 x Exhaust pipe
  • 1 x Intake pipe
  • 1 x Air Outlet Pipe
  • 1 x Air Filter
  • 1 x Vents
  • 1 x Fixture Accessories set
  • 1 x Controller extension cord

Note: The adapter for the US warehouse is US Plug, while the one for the Czech warehouse is EU Plug.

3.1 Internal Key Parts Terminology

Understanding the internal components is crucial for maintenance and troubleshooting.

Internal Key Parts Terminology Diagram
Figure 3.2: Internal Key Parts Diagram. Labels include Control box, Ignition plug, Safety plug, Air outlet, Combustion chamber, Heating zone, Air inlet, Air fan, Flame retardant impeller.

4. Installation Instructions

The installation difficulty of this toolbox compact heater is relatively low, as many pipeline installation processes have been simplified. You primarily need to install the exhaust pipe and connect the AC-DC power supply to begin operation.

Installation Diagram
Figure 4.1: Basic Installation Diagram showing the heater, exhaust pipe, and power connection.

Important Installation Notes:

  • Exhaust Pipe: Extend the exhaust pipe outside to expel combustion exhaust gas.
  • Power Supply: Use a 12V or 24V DC power supply, or an AC to DC adapter. The discharge current is recommended to be greater than 15A (the device needs to heat the glow plug when starting, and the operating current may reach 12A and last for 3-5 minutes).
  • WARNING: The exhaust pipe works at a very high temperature! During installation, use, maintenance, and scrapping of this machine, there shall be no flammable or explosive materials around the exhaust pipe, and care shall be taken to avoid igniting flammable materials that may cause fire. The discharged exhaust gas can reach temperatures as high as 400°C. Keep it away from pets and children, and be aware of the gap from the ground to avoid damaging your floor or lawn.

5. Operating Instructions

5.1 Control Panel Overview

Control Panel Layout
Figure 5.1: Control Panel Layout. Key elements include Add key, Power on/off key, Minus key, OK key, Altitude display, Clock display, Display data and parameters, Power bar, Host appearance.

Icon Meanings:

IconMeaningIconMeaning
FanFanBluetooth symbolBluetooth connection
!Fault promptsensor failureSensor failure
Plateau statusPlateau mode activeAAutomatic start/stop
Power failurePower failureTimer alarmTimer set
Ventilation statusVentilation modeIgnition plugIgnition plug activity
Carbon monoxide alarmCO alarmManual modeManual control
Fuel pumpFuel pump activityHigh temperature alarmHigh temperature
Constant temperature modeConstant temperature control

5.2 General Operation

5.2.1 Power On/Off

  1. Power-on: In the off state, press and hold the "Power" button for 2 seconds to turn on the device.
  2. Shutdown: In the power-on state, press and hold the "Power" button for 2 seconds. The device will enter the shutdown and cooling process, and the display will show "OFF". The device will shut down after cooling. Do not force power off when it displays "OFF". Power off will damage accessories due to high internal temperature. Wait until the machine displays in the shutdown state before powering off.

5.2.2 Manual Mode Operation

Manual mode has 10 gears (H1-HH10), where HH10 is maximum power. Press the "Up" or "Down" key to increase/decrease the gear. The display will show the current gear.

5.2.3 Constant Temperature Mode Operation

In constant temperature mode, press the "Up" or "Down" key to increase or decrease the target temperature. The setting range is 0 to 40 °C. Press and hold the "Mode" button for 2 seconds to switch between manual and constant temperature mode.

5.2.4 Automatic Start-Stop Operation

In the power-on state, when in constant temperature mode, short press the "Mode" key. The "A" icon will display, indicating that the automatic start/stop function is enabled. Short press the "Mode" key again, and the "A" icon will disappear, indicating the function is turned off.

  • Default power-on temperature: -4°C.
  • Default power-off temperature: +3°C.
  • Example: If set to 24°C, the machine will automatically shut down when ambient temperature reaches 27°C and start up when it reaches 20°C. These values can be changed via the mobile phone APP.

5.2.5 Ventilation Operation

In the off state, press and hold the "Fan" key for 2 seconds to turn on ventilation mode. The fan icon will display.

  1. Press the "Up" or "Down" key to adjust the fan speed gear.
  2. Press and hold the "Fan" key for 2 seconds to exit ventilation mode.

5.2.6 Switch to Display Data at Startup

In the power-on state, short press the "OK" button to cycle through displayed data. The order is: case temperature -> working voltage -> ambient temperature -> carbon monoxide concentration -> current gear (or current set temperature).

5.2.7 Temperature Unit Switching

Press and hold the "Up" and "Down" keys simultaneously for 2 seconds to switch between °C and °F.

5.2.8 Manual Oiling Operation

In the off state, press the "Up" and "Down" keys simultaneously for 2 seconds to manually control the oil pump. Release the keys to stop pumping oil. Please use with caution!

5.2.9 Altitude Enabling Operation

Press and hold the "OK" and "Up" keys simultaneously for 2 seconds. The "Plateau" icon will display, turning on plateau mode and including the equipment air-oil ratio in the altitude conversion. Press and hold "OK" and "Up" again for 2 seconds to turn off the plateau mode (icon disappears), indicating altitude is not included in conversion.

5.2.10 Scheduled On/Off Operation

Press and hold the "OK" and "Up" keys simultaneously for 2 seconds. If no timer is set, it will enter the timer setting interface, and the timer symbol will display.

The digital display "CLOS" is for setting shutdown time, and "OPEN" is for setting startup time. If a timer is already on, turn off all timers and the timer symbol will disappear.

  1. Press "Up" or "Down" key to adjust the time value (range: 00:00~23:59).
  2. Press the "Mode" key to switch the adjustment digit; the corresponding digit will flash.
  3. Press the "OK" button to save settings. If setting power-on time, it will switch to power-off time setting; otherwise, it exits.
  4. If no key operation for 10 seconds, settings are saved, and the interface exits.
  5. Press the "Cancel" key to not save the set value. If setting power-on time, it will switch to power-off time setting; otherwise, it exits.

After timing is enabled, the timer symbol flashes. The machine will automatically turn on at the scheduled power-on time and turn off at the scheduled power-off time.

After turning on timing, press the "Mode" key to view all daily timing times.

5.2.11 Clock Synchronization Operation

Press and hold the "Mode" button for 2 seconds to enter the clock adjustment interface. The digital data will display "CLOC".

  1. Press "Up" or "Down" key to adjust the time value (range: 00:00 ~ 23:59).
  2. Press the "Mode" key to switch the adjustment digit; the corresponding digit will flash.
  3. Press the "OK" button to confirm the time and enter the day of the week setting.
  4. Press the "Mode" key to enter the day of the week setting.
  5. The interface exits after 10 seconds of no key operation.

Setting the Weekday Operation (Digital display "EE-1"):

  1. Press "Up" or "Down" key to adjust the decimal point.
  2. Press the "OK" button to confirm the time and exit the clock adjustment interface.
  3. Press the "Mode" key, or the interface exits after 10 seconds of no key operation.

When the APP is opened and connected to Bluetooth, the phone time will be automatically synchronized.

5.2.12 Wireless Remote Control Matching Operation

In the off state, press and hold the "Mode" and "Up" keys simultaneously for 2 seconds. "HFA1" will be displayed.

  1. Press the "Up" or "Down" key to adjust the 4th digit, which is the remote control number (1 to 3, corresponding to 3 remotes).
  2. Select the remote control number and press any button on the remote control to pair. After successful pairing, exit the pairing state.
  3. Press the "Mode" key to exit remote control pairing.

*The remote control is wireless and bidirectional, and only supports one-to-one operation. Multiple remote controls working at the same time will affect wireless data transmission and cause data confusion.

5.2.13 Screen Brightness Adjustment

In the power-on state, press and hold the "Up" and "Down" keys simultaneously for 2 seconds. The "AIRHEATER" English letter icon in the upper left corner will flash. Adjust brightness by clicking the "Up" or "Down" key. After adjustment, press and hold "Up" and "Down" again for 2 seconds to confirm. The screen brightness is automatically confirmed after 10 seconds of no action.

5.2.14 Check Bluetooth Password

Press "OK" and "Up" keys simultaneously. The screen will display a 4-digit number, which is the Bluetooth connection password (initial password is "0000").

5.2.15 Bluetooth Password Initialization

When the device is powered off, press and hold "OK" and "Up" keys simultaneously for 2 seconds to enter the password input state. The password is "3333".

  1. Press the "Up" or "Down" key to adjust the number size.
  2. Press the "Mode" key to switch the adjustment digit; the corresponding digit will flash.
  3. Press the "OK" button to confirm the Bluetooth password initialization.
  4. Press the "Mode" key to cancel the operation.

5.2.16 Oil Pump Frequency Adjustment (Non-professionals are prohibited to use)

In the off state, press and hold "OK" and "Up" keys simultaneously for 2 seconds to enter the password input state. The password is "3638".

After entering the password, "1-2.0" is displayed, meaning the oil pump frequency of 1st gear is 2.0 (10th gear is replaced by letter A).

  1. Press the "Up" or "Down" key to increase or decrease the oil pump frequency.
  2. Press the "Mode" key to switch the oil pump gear.
  3. Press the "OK" button to confirm the operation.
  4. Press the "Mode" key to cancel the operation.

5.2.17 Carbon Monoxide Action Value Setting

In the shutdown state, press and hold "OK" and "Up" keys simultaneously for 2 seconds to enter the password input state. The password is "5555". Click "OK" to enter modification. The display "set L500" means 500ppm is the shutdown value, and the alarm value is the set value * 0.7.

  1. Press the "Up" or "Down" key to adjust the number size.
  2. Press the "Mode" key to switch the adjustment digit; the corresponding digit will flash.
  3. Press the "OK" button to confirm the carbon monoxide shutdown value setting.
  4. Press the "Mode" key to cancel the operation.

5.3 Bluetooth APP Control

This panel supports mobile phone APP to control this device via Bluetooth. If you have the Bluetooth version, you can control your parking heater through the app.

5.3.1 How to Download the APP

Android users can download the installation package from the Google Play store. Apple users can download from the App Store. Alternatively, scan the QR code to install the "Hcalory" APP.

QR code for Android App
QR Code for Android App
QR code for iOS App
QR Code for iOS App

5.3.2 Instructions for App Operation

  1. Adding a Device: When you first open the application, click the "+" sign to add a device.
  2. Bluetooth and Location Permissions: When searching for devices, you need to turn on Bluetooth and authorize precise positioning information. Refusing authorization may prevent your phone from finding nearby devices.
  3. Allow Hcalory to Connect: Before making a Bluetooth connection, you need to allow the Hcalory app to discover and connect to nearby devices.
  4. Manual Bluetooth Selection: If the Bluetooth interface does not pop up automatically, click the Bluetooth icon within the app to search for nearby Bluetooth devices. Select the device with "hcalory" in its name. If your phone is already connected to a device, other phones cannot connect simultaneously until your phone exits the connection.
  5. Post-Connection: After successful connection, the device can carry out various operations via the app.

App Control Modes:

  • Start Heating: Click the [heating button] to start regular heating. You can choose [temperature mode] or [gear mode].
    • Temperature Mode: Device intelligently controls gears based on set target temperature. Suitable for indoors.
    • Gear Mode: Device runs at a fixed gear. Suitable for open areas or tents with poor insulation.
  • Fan Mode: The fan starts independently without combustion. Can be used as a fan or exhaust fan.
  • Plateau Button: Due to low air pressure and oxygen at high altitudes, the air-fuel ratio for combustion differs. When the plateau key is on, the device simulates high-altitude environments and adjusts oil pump frequency. Recommended for 2000-5000 meters above sea level. Not recommended for prolonged use above 4000 meters without spare parts due to complex outdoor conditions.
  • Scheduled Timing: Set multiple timers for on/off functions. The heater device must remain powered on for timed functions to execute.
  • Other Settings: Adjust interface language/temperature units and provide user feedback via email.

6. Troubleshooting and Error Codes

If a fault occurs, the digital display will show an "E-XX" code (e.g., "E-21") and the fault symbol will flash. Refer to the table below for meanings and solutions.

6.1 Fault Alarm

Digital display "E-21". The fault symbol flashes and the corresponding faulty device icon flashes. The displayed data is the fault code. Please refer to the fault table for its meaning.

6.2 Error Code Table

Fault CodeCauseSolution
Power supply voltage is too low1) Check if battery connection wires are damaged or connectors are secure. 2) Check if the fuse is aging.
E022Power supply voltage is too highThe power supply voltage is too high; check battery output voltage range.
E023Abnormal power supply voltagePower supply voltage selection is abnormal; check battery output voltage range.
E031Ignition plug open circuit1) Check if connecting wires and connectors of ignition plug are loose or broken. 2) Check if ignition plug connection plug is loose. 3) Connect ignition plug to check if it is damaged.
E032Glow plug short circuit1) Check if connecting wire of ignition plug is short-circuited. 2) Ignition plug is damaged or the main board reads incorrectly.
E041Oil pump open circuit1) Check if connecting wires and connectors of oil pump are damaged, loose or broken. 2) Check if the oil pump is damaged.
E042Oil pump short circuit1) Check if connecting wire of oil pump is short-circuited. 2) Check if the oil pump is blocked or damaged.
E05High temperature alarm (housing > 230°C)1) Check if cold air inlet is blocked. 2) Check if hot air outlet pipe is bent or blocked. 3) Check if the fan is running normally. 4) Check if the sensor is damaged.
E061Motor open circuit1) Check if connecting wires of the motor are broken or motor connecting wire connector is loose. 2) Connect the motor to the power supply and check if it rotates.
E062Motor short circuit1) Check if connecting wires of the motor are short-circuited. 2) The motor is damaged or the main board is misread.
E063Abnormal fan speed1) Check if the impeller is stuck. 2) The gap between the magnet on the wind wheel and the Hall sensor on the controller is too large.
E07Communication between main board and remote control switch board is abnormal1) Check if connection port of remote control switch is loose. 2) Check if connection line (blue) of remote control switch is broken.
E0BTurn off the flame1) Check for oil shortage, oil freezing, oil circuit blockage, oil pipe folding, or too many steam drums in oil pipe, or oil pump stuck. 2) Check if oxygen inlet and exhaust air ducts are unobstructed. 3) Check if housing temperature sensor is in full contact with housing and if compression spring is strong. 4) Check if the sensor is damaged.
E091Temperature sensor open circuit1) Check if temperature sensor connection wire and connector are damaged or loose. 2) Check if the sensor is damaged.
E092Temperature sensor short circuit1) Is the temperature sensor connection line short-circuited? 2) Check if the sensor is damaged.
E10Startup failed1) Casing temperature too high, cannot cool down after 3 minutes of startup. 2) White smoke at exhaust port: 2.1) Check if filter next to ignition plug is clean. 2.2) Check if oil pump sprays oil effectively. 2.3) Check if ignition plug is aged. 3) Small amount of white smoke or no smoke: 3.1) Check for oil shortage, frozen or blocked oil circuit. 3.2) Check if oil pump is stuck or damaged. 3.3) Check if combustion air intake and exhaust passages are unobstructed. 3.4) Check if ignition plug is damaged. 3.5) Is the gap between inner wind wheels too large? 4) Ignition is normal but ignition failure is still reported: Check if housing temperature sensor is in full contact with housing and if compression spring is strong. Is the sensor normal?
E11Carbon monoxide concentration exceeds limitIncrease air exchange in the environment to reduce carbon monoxide concentration; evacuate personnel to a safe environment.

7. Specifications

AttributeValue
Brand NameHcalory
Model NameTB
Power8KW
Voltage12VDC, 24V DC, 100-240V AC
Fuel TypeDiesel
Fuel Tank Capacity6L
MaterialPlastic and Metal
Item TypeHeating & Fans
Item Length48.8cm
Item Width20cm
Item Height38cm
Item Diameter9cm
Item Weight9.6kg
Diesel Consumption0.04 gal/h - 0.12 gal/h
Operating Temperature-40℃~40℃ (-40℉~104℉)
External Testing CertificationCE
CertificationCE, RoHS
OriginMainland China
Switch TypeLCD Switch
TB2-SE SwitchMVP 2.1
TB2-P SwitchWireless Temperature Sensing Switch
LCD Panel Cable150CM
AdapterInclude
Plateau Mode Altitude Reference2500m/5000m (Auto Adjustment with altitude sensor)
LCD Panel ControlSupport
Remote ControlSupport
Bluetooth APP ControlSupport
CO Alarm Sensor (TB2-P)Support
CO Alarm Sensor (TB2-SE)Do not support

8. Maintenance

Regular maintenance ensures the longevity and efficient operation of your Hcalory Parking Heater.

  • Cleaning: Ensure the air inlet and exhaust ducts are free from obstructions. Regularly check and clean the filter next to the ignition plug.
  • Fuel System: Periodically check for any signs of oil leakage, oil freezing, or blockages in the oil circuit and pipes. Ensure the oil pump is functioning correctly.
  • Sensors: Verify that all sensors, especially the housing temperature sensor, are in proper contact and not damaged.
  • Electrical Connections: Inspect all wiring and connectors for looseness, damage, or short circuits.
  • Fan and Impeller: Check that the fan is running normally and the impeller is not stuck. Ensure the gap between the magnet on the wind wheel and the Hall sensor is correct.
  • Exhaust System: Ensure the exhaust pipe is not bent or blocked and is properly extended outdoors.
  • Professional Service: For complex issues or replacement of critical components, always consult with customer service or a qualified professional. Do not attempt to open the controller case or replace important parts without authorization.

9. User Tips

  • For optimal heating efficiency and safety, always ensure proper ventilation and that the exhaust pipe is directed outside.
  • Utilize the Bluetooth APP control for convenient remote management of temperature, timing, and monitoring, especially in cold conditions.
  • When operating at high altitudes, remember to activate the "Plateau Mode" for adjusted combustion parameters and efficient performance.
  • Pay attention to the CO alarm sensor (if applicable to your model) and ensure it is functioning correctly for carbon monoxide detection.
  • To prevent damage, always allow the heater to complete its cooling cycle (3-5 minutes) after turning it off before disconnecting power.

10. Support and Contact Information

Thank you for your support and trust in us. Parking heater structures are complex, and you may use them in various outdoor or indoor environments, therefore you may encounter various unexpected situations. If you encounter difficulties that you cannot resolve, you can contact us, and we will guide you in adjustments or repairs.

If you need our after-sales technical support, or if you have any questions about our products, you can send an email to hcalory@hcalory.com or contact our after-sales personnel through the sales platform where you purchased the product. We will provide you with more detailed instructions or operational videos. Thank you for your feedback and support.

Item guides & documents: A user manual in PDF format is available for detailed reference. View User Manual (PDF)

11. Product Video

Product overview video demonstrating features like portability, heating efficiency, and quiet operation in various environments.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.