DAKEFPV H743 Flight Controller and 70A 4in1 ESC Stack

Contents

DAKEFPV H743 Flight Controller and 70A 4in1 ESC Stack Instruction Manual

Model: H743 Flight Controller and 70A 4in1 ESC Stack

1. Introduction

This manual provides detailed instructions for the DAKEFPV H743 Flight Controller and the DAKEFPV 70A 4-in-1 Electronic Speed Controller (ESC) stack. This high-performance stack is designed for FPV (First Person View) drones, supporting both BetaFlight and ArduPilot firmware. It features a powerful STM32H743 microcontroller, dual gyroscopes, a built-in barometer, and ample connectivity options for various peripherals including DJI Air Units, GPS, and multiple motors.

2. Safety Information

Please read and understand all safety warnings and instructions before using this product. Improper use can lead to damage to the product, property, or serious injury.

  • Always ensure correct polarity when connecting power. Incorrect polarity will damage the device.
  • Avoid short circuits during installation and operation.
  • Use the recommended Low ESR capacitor to prevent voltage spikes and potential damage to the stack.
  • Ensure proper insulation of all exposed wires, especially after soldering or modifying connections.
  • Keep the flight controller and ESC away from water, moisture, and extreme temperatures.
  • This product is intended for users aged 14 and above.
  • Damage resulting from improper installation or use is not covered under warranty.

3. Package Contents

The contents of your package may vary depending on the option purchased. Please verify your package against the lists below:

Option 1 - DAKEFPV H743 70A 30x30 STACK

Package contents for DAKEFPV H743 70A 30x30 Stack

Image: Components included in the DAKEFPV H743 70A 30x30 Stack package.

  1. DAKEFPV H743 Flight Controller x 1
  2. DAKEFPV BLS 70A 4 in 1 ESC x 1
  3. 35V 1000uF Low ESR Capacitor x 1
  4. M3 Nylon Nut x 5
  5. M3 silicone O Ring x 5
  6. M3*8mm Silicone Grommets (for FC) x 1
  7. M3*8.1mm Silicone Grommets (for ESC) x 1
  8. SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  9. SH 1.0mm 75mm-length 8pin Cable x 1
  10. M3*30mm Inner-hexagon Screws x 5
  11. GPS 6pin cable, Analog VTX 6pin cable, Dual-camera 6pin cable x 1
  12. XT60 Power Cable (70mm) x 1

Option 2 - DAKEFPV H743 70A 30x30 FC

Package contents for DAKEFPV H743 70A 30x30 FC

Image: Components included in the DAKEFPV H743 70A 30x30 FC package.

  1. DAKEFPV H743 Flight Controller x 1
  2. Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone O-rings x 5
  3. FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  4. GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3 - DAKEFPV 8S 70A 4 in 1 ESC

Package contents for DAKEFPV 8S 70A 4 in 1 ESC

Image: Components included in the DAKEFPV 8S 70A 4 in 1 ESC package.

  1. DAKEFPV 8S 70A 4 in 1 ESC x 1
  2. 35V 1000uF Low ESR Capacitor (Note: 12S ESC Send 63V1000uF Capacitor)
  3. FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  4. XT60 x 1

4. Product Overview

4.1 Key Features

Key features of DAKEFPV H743 Stack

Image: Overview of the DAKEFPV H743 Flight Controller and 70A 4in1 ESC features.

  • Flight Controller (FC):
    • Main Control Chip: STM32H743
    • Firmware Support: BetaFlight (default), ArduPilot
    • Gyroscope: Dual ICM42688P
    • Barometer: Built-in for real-time altitude sensing
    • OSD Chip: AT7456E
    • Black Box: Built-in 16MB high-speed FLASH for continuous flight status recording (sensor data, control commands, fault codes). Data can be retrieved for accident analysis even after a crash or power outage.
    • BEC: 12V 3A + 5V 3A dual independent BEC
    • UART Serial Ports: 8 groups
    • Motor Support: Supports up to 8 motors (M1-M8), suitable for X8, Y6, and fixed-wing aircraft.
    • DJI Air Unit Direct Plug Interface: Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.
    • Battery Capacity Indicator: 4-level indicator (FCC, 3V, 5V, 12V) on the FC.
    • Additional Features: Ample pads reserved for enthusiasts, supports external GPS module (powered by 5.0V), LED light bar pads, buzzer pads.
  • Electronic Speed Controller (ESC):
    • Continuous Current: Real 70A x 4 channels
    • Peak Current: 280A for 10 seconds
    • Firmware: BLHeli_s/BLUEJay
    • Motor Protocol: Dshot300/Dshot600/PWM/Bi-directional Dshot
    • Power Supply: Optimized circuit design with 3-ounce copper PCB, upgraded MOS tubes, and aluminum alloy heat sink for stable output.
    • Protection: Built-in TVS surge suppression diode, 21 imported Japanese TDK 35V 22uF SMD filter capacitors, and a standard 1000uF true high-frequency low-resistance electrolytic capacitor to filter signal interference.

4.2 Layout and Pinout

Understanding the layout and pin assignments is crucial for correct installation and wiring.

H743 Flight Controller Pinout

Image: DAKEFPV H743 Flight Controller Top View Pinout.

H743 Flight Controller Component Layout

Image: DAKEFPV H743 Flight Controller Component Layout with labels.

BLS 70A 4-in-1 ESC Motor Pads

Image: BLS 70A 4-in-1 ESC Motor Pads.

H743 Flight Controller 8 Motor Support

Image: H743 Flight Controller showing M1-M8 outputs for 8-motor support.

5. Setup and Installation

5.1 Stack Installation Note

Important Stack Installation Note

Image: Diagram illustrating the importance of proper spacing and silicone pad placement during stack installation.

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.

It's critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated in the image above. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

5.2 Capacitor Installation

To prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package. Solder the capacitor to the designated BAT+ and BAT- pads on the ESC.

5.3 FC and ESC Connection

The FC and ESC can be connected via the provided SH 1.0mm 8-pin cable. Alternatively, direct soldering is possible. Refer to the wiring diagrams for soldering pad definitions.

6. Wiring Diagrams

6.1 General Wiring Diagram

Comprehensive Wiring Diagram

Image: Comprehensive wiring diagram showing connections for FC, ESC, motors, GPS, ELRS, VTX, DJI Air Unit, LED, Buzzer, and Servo.

6.2 DJI O3 Air Unit Connection

DJI O3 Air Unit Connection

Image: Diagram showing cable connection between the FC and DJI O3 Air Unit. Use the 6-pin cable that comes with the O3 Air Unit.

RunCam Link / Caddx Vista / DJI Air Unit V1 Connection

Image: Diagram showing cable connection between the FC and RunCam Link/Caddx Vista Air Unit or DJI Air Unit V1. Use the 6-pin cable that comes with the H743 stack.

6.4 Important Notice for SBUS Receiver with DJI Air Unit

ELRS Receiver SBUS Disconnection Diagram

Image: Diagram illustrating the necessary SBUS wire disconnection for ELRS receivers when used with DJI Air Units.

When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).

If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1) simultaneously, you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

DO NOT connect this wire to assure the external SBUS receiver works properly!

7. Configuration

The DAKEFPV H743 Flight Controller supports both BetaFlight (default factory firmware) and ArduPilot. You will need to connect the FC to your computer via the USB Type-C port and use the respective configurator software (BetaFlight Configurator or Mission Planner for ArduPilot) to set up your drone.

  • Firmware Target Name: DAKEFPVH743
  • DFU Mode: To enter DFU mode for firmware flashing, press and hold the BOOT button while powering on the flight controller.
  • Gyro/Motor Orientation: The orientation of the gyro and motor sequence can be adjusted through the firmware settings.

8. Operation

8.1 Battery Capacity Indicator

Battery Capacity Indicator on FC

Image: The 4-level battery capacity indicator on the Flight Controller.

On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on goggles to check the battery status. The indicators typically represent FCC, 3V, 5V, and 12V levels.

9. Troubleshooting

  • ELRS Receiver Not Recognized: If your ELRS receiver is not recognized when used with a DJI Air Unit (O3/Link/Vista/Air Unit V1), ensure you have disconnected the SBUS signal wire from the Air Unit harness as described in Section 6.4.
  • Power-on Burnout: Always use the recommended Low ESR capacitor to protect against voltage spikes during power-on.
  • Short Circuit Issues: Verify proper installation of the stack, especially ensuring adequate space and correct silicone pad placement to prevent contact between the FC's USB port and the ESC.
  • Firmware Issues: If you encounter issues with the flight controller's firmware, you can force DFU mode by holding the BOOT button during power-up and re-flash the firmware using BetaFlight Configurator or Mission Planner.

10. Specifications

10.1 DAKE H743 30x30 Flight Controller

DAKE H743 Flight Controller Specifications

Image: Detailed specifications for the DAKE H743 Flight Controller.

FeatureSpecification
Product NameDAKE H743 30 x 30 Flight Controller
Main ControlSTM32H743
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENone
WIFINot supported
DJI Air Unit ConnectionSupports 6pin socket direct plug and solder wire connection. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire sequence change needed.
FLASH (Black Box)16MB Flash
AmmeterSupported
Input Voltage3-8S LiPo battery
UART Serial Ports8 groups
Buzzer PadsSupported (BZ+, BZ- pads connect to 5V active buzzer)
BOOT ButtonPress and hold BOOT button and power on simultaneously to force DFU mode for firmware flashing.
RSSI PadSupported (Located on the top front R5 pad)
SmartPort / F.PortNot supported
Supported FirmwareBetaFlight (default), ArduPilot
Firmware Target NameDAKEFPVH743
Mounting Holes30.5 x 30.5mm (4mm hole diameter)
Dimensions36 x 36 x 8 mm
Weight10.5g

10.2 DAKE 70A 4 in 1 ESC

DAKE 70A 4 in 1 ESC Specifications

Image: Detailed specifications for the DAKE 70A 4 in 1 ESC.

FeatureSpecification
Product NameDAKE 12S 70A 4 in 1 ESC (Note: Product name indicates 12S, but specification table lists 3-8S input. Please verify with manufacturer if 12S operation is intended.)
FirmwareBLHeli_s/BLUEJay
Battery Input3-8S LiPo battery
Continuous Current70A x 4
Max Current80A x 4 - 10S
Built-in TVS DiodeYes
Built-in Capacitor1000uF high frequency low resistance capacitor (included in package)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Input Voltage3-8S LiPo battery
Output VoltageVBAT
AmmeterSupported (Scale=400, Offset=0)
ESC TelemetryNot supported
Mounting Holes30.5 x 30.5mm (4mm hole diameter)
Dimensions45.4 x 42.8 x 6.5mm
Weight23.5g

10.3 Stack Dimensions

DAKEFPV H743 Stack Dimensions

Image: Dimensions of the H743 Flight Controller and the assembled stack.

  • Flight Controller: 36 x 36 x 8 mm
  • ESC: 45.4 x 42.8 x 6.5 mm
  • Assembled Stack Height: 15.8 mm
  • Mounting Holes (FC & ESC): 30.5 x 30.5 mm (M4)

11. User Tips

  • Voltage Compatibility: While the product name for the ESC mentions '12S', the detailed specifications for both the FC and ESC list '3-8S LiPo battery' as the input voltage. If you intend to use a 12S battery, please confirm compatibility with the manufacturer to avoid damage.
  • ELRS Receiver Setup: Remember the critical step of disconnecting the SBUS signal wire from the DJI Air Unit harness if you are using an ELRS receiver with a DJI Air Unit to ensure proper functionality.
  • Data Logging: Utilize the 16MB onboard FLASH for flight data recording. This can be invaluable for analyzing flight performance and troubleshooting issues.
  • USB Power for Debugging: When powered via USB, the FC can supply power to the receiver, which is useful for debugging and initial setup without needing a full battery connection.

12. Warranty and Support

DAKEFPV products are manufactured to high-quality standards. For warranty claims or technical support, please contact the seller or DAKEFPV customer service directly. Please note that damage caused by improper installation, modification, or misuse is not covered under warranty.

For the latest firmware, software, and additional resources, please visit the official DAKEFPV website or relevant community forums for BetaFlight and ArduPilot.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.