JINGSHA X99M-A

Contents

JINGSHA X99M-A Motherboard LGA 2011 Set User Manual

Model: X99M-A Motherboard with E5 2650 V4 CPU and 16GB DDR4 REG ECC RAM

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your JINGSHA X99M-A Motherboard LGA 2011 Set. This kit includes the X99M-A motherboard, an Intel Xeon E5 2650 V4 CPU, and 16GB (2x8GB) DDR4 REG ECC RAM. Please read this manual thoroughly before proceeding with installation to ensure proper setup and optimal performance.

JINGSHA X99M-A Motherboard with CPU and RAM
Figure 1: JINGSHA X99M-A Motherboard LGA 2011 Set components.

2. Package Contents

Verify that all items listed below are present in your package:

  • 1 x JINGSHA X99M-A LGA2011 Motherboard
  • 1 x Intel Xeon E5 2650 V4 CPU (used, good condition)
  • 2 x DDR4 8GB 2400MHz ECC REG RAM (total 16GB, used, good condition)
  • 1 x SATA Cable
  • 1 x Backplane (I/O Shield)

Note:

  • The motherboard battery is removed before shipment due to shipping regulations. You will need to install a CR2032 coin cell battery (not included) for the CMOS to retain settings.
  • Due to different production batches, the color of DIMM slots, SATA ports, PCI or PCI-E slots, and other ports may vary. This does not affect product quality or functionality.
Product packaging showing motherboard, CPU, and RAM
Figure 2: Example of product packaging and included components.

3. Setup Instructions

Follow these steps carefully to assemble your motherboard kit.

3.1 Motherboard Layout Overview

JINGSHA X99M-A Motherboard layout diagram with labeled ports and connectors
Figure 3: X99M-A Motherboard Layout. Key components include 4*DDR4 Slots, LGA 2011-3 CPU Socket, 1*8pin 12V Connector, 1*24pin ATX Connector, 4*SATA3.0, M.2 NGFF/NVMe slot, 1*PCIE3.0 x16, 3Pin CPU_FAN, 3-in-1 Audio, Front Audio Header, F_USB3.0 Header, F_USB2.0 Header, 3Pin SYS_FAN, Speaker Header, AUTO_ON Header, HDD LED, PWR LED, RST SW, PWR SW, 1*Gigabit Ethernet, 2*USB3.0, 6*USB2.0.

3.2 CPU Installation (LGA 2011-3)

  1. Carefully open the CPU socket retention mechanism on the motherboard.
  2. Align the triangular mark on the Intel Xeon E5 2650 V4 CPU with the corresponding mark on the LGA 2011-3 socket.
  3. Gently place the CPU into the socket without forcing it.
  4. Close the retention mechanism to secure the CPU.
  5. Apply thermal paste to the CPU and install a compatible CPU cooler (not included).

3.3 RAM Installation (DDR4)

The motherboard supports 4*UDIMM DDR4 memory modules in dual-channel configuration, up to 128GB. The included RAM is 2x8GB DDR4 REG ECC 2400MHz.

  1. Locate the four DDR4 DIMM slots on the motherboard.
  2. Open the clips at both ends of the DIMM slots.
  3. Align the notch on the RAM module with the key in the DIMM slot.
  4. Insert the RAM module firmly into the slot until the clips snap into place. For dual-channel operation, install modules in alternating slots (e.g., slots 1 and 3, or 2 and 4).

3.4 Storage Installation

The motherboard features 4 SATA 3.0 ports and 1 M.2 2280 NVMe 3.0x4 Port + 1 M.2 2280 NGFF Port.

  • **SATA Drives**: Connect your SATA hard drives or SSDs to the SATA 3.0 ports using SATA data cables (one included).
  • **M.2 SSDs**: Install M.2 NVMe or NGFF SSDs into the designated M.2 slots. Secure the M.2 drive with the provided screw.
Close-up of the M.2 NVMe/NGFF slot on the motherboard
Figure 4: M.2 NVMe/NGFF slot for high-speed storage.

3.5 Power Connections

Connect the power supply unit (PSU) cables to the motherboard:

  • Connect the 24-pin ATX power connector from your PSU to the 24-pin ATX socket on the motherboard.
  • Connect the 8-pin 12V CPU power connector from your PSU to the 8-pin 12V socket near the CPU.
  • Ensure your power supply is at least 500W to adequately support this platform.

3.6 Peripheral Connections

  • **USB**: Connect front panel USB headers (F_USB3.0, F_USB2.0) to your case's USB ports. The back panel provides 2 USB 3.0 ports and 6 USB 2.0 ports.
  • **LAN**: Connect an Ethernet cable to the Gigabit Ethernet port (RTL8111H).
  • **Audio**: Connect front panel audio headers to your case's audio ports. The back panel provides 3-in-1 audio jacks.
  • **Expansion Cards**: Install your PCI-E 3.0 x16 graphics card or other expansion cards into the available slot.
Rear I/O panel of the JINGSHA X99M-A Motherboard
Figure 5: Rear I/O Panel with USB, LAN, and Audio ports.

4. Operating Instructions

  1. After completing all hardware installations, connect your monitor, keyboard, and mouse.
  2. Connect the power cable to your power supply unit and turn on the PSU switch.
  3. Press the power button on your computer case.
  4. The system should boot up. You may need to enter the BIOS/UEFI setup to configure boot order, enable XMP for RAM (if applicable), or adjust other settings. Typically, you can access BIOS by pressing 'DEL' or 'F2' during startup.
  5. Install your preferred operating system.
  6. Install necessary drivers for the motherboard components (chipset, LAN, audio, etc.). BIOS files and drivers can be obtained by contacting customer service.

5. Maintenance

  • **Cleaning**: Regularly clean dust from inside your computer case, especially around the CPU cooler, RAM, and GPU, using compressed air. Ensure the system is powered off and unplugged before cleaning.
  • **BIOS Updates**: Periodically check the JINGSHA official website or contact customer service for BIOS updates. Update BIOS only if necessary and follow instructions carefully to avoid system instability.
  • **Driver Updates**: Keep your system drivers updated for optimal performance and stability.
  • **Physical Inspection**: Occasionally inspect the motherboard for any loose connections, damaged components, or signs of overheating.

6. Troubleshooting

  • **No Power/No Boot**:
    • Ensure all power cables (24-pin ATX, 8-pin 12V CPU) are securely connected.
    • Verify your power supply unit (PSU) is at least 500W and functioning correctly.
    • Check front panel power switch connections to the motherboard.
    • Ensure the CMOS battery is installed correctly.
  • **System Instability/Crashes**:
    • Check CPU and RAM installation. Reseat them if necessary.
    • Ensure CPU cooler is properly installed and making good contact.
    • Verify RAM modules are installed in the correct slots for dual-channel operation.
    • Update drivers for all components.
  • **Component Not Detected**:
    • Reseat the component (e.g., graphics card, M.2 SSD).
    • Check cable connections for SATA drives.
    • Ensure the component is compatible with the motherboard.
  • **General Issues**:
    • If the product has quality problems within 15 days of receipt, please provide video proof to customer service for a solution.
    • For issues during the warranty period, contact customer service first. You may be directed to a repair center or asked to return the product to the Chinese factory for repair.
    • Any negative feedback, including issues caused by improper use or burning out the motherboard, may void after-sales service.

7. Specifications

Detailed specifications for the JINGSHA X99M-A Motherboard:

Feature Specification
Part# X99M-A Motherboard
Form Factor Micro-ATX (190mm*190mm)
CPU Socket LGA2011-3 (Supports Intel Xeon E5 V3/V4 CPU)
RAM Slots 4 x UDIMM DDR4 (1600/1866/2133/2400 MHz), Dual Channel, Up to 128GB
SATA Ports 4 x SATA 3.0
M.2 Slots 1 x M.2 2280 NVMe 3.0x4 Port, 1 x M.2 2280 NGFF Port
USB Interface 8 x USB 2.0 Ports, 4 x USB 3.0 Ports (2*USB3.0, 6*USB2.0 on back panel)
LAN 1 x RTL8111H Gigabit Ethernet (1000Mbps)
Expansion Slot 1 x PCIE 3.0 x16 slot
Sound Card 5.1 Channel HD Audio chip
Electric Yes
High-concerned chemical None
Origin Mainland China
Product Parameter table from seller description
Figure 6: Product Parameter table.

8. Warranty and Support

  • **Motherboard Warranty**: JINGSHA offers a one-year warranty for the X99M-A Motherboard.
  • **CPU and RAM Warranty**: The included CPU and RAM are used components but are in good condition and come with a one-year warranty.
  • **Technical Support**: JINGSHA provides free lifetime technical support for this product.
  • **BIOS and Drivers**: BIOS files and drivers for the motherboard are available upon request from customer service.
  • **Warranty Claims**: For any warranty claims or technical assistance, please contact JINGSHA customer service.

9. User Tips

  • **Power Supply**: Always use a reliable power supply unit of at least 500W to ensure stable operation, especially with high-performance components.
  • **Cable Management**: Good cable management improves airflow and makes future maintenance easier.
  • **Static Discharge**: Always ground yourself before handling internal computer components to prevent electrostatic discharge (ESD) damage.
  • **Component Compatibility**: While this kit is pre-matched, always verify compatibility when adding new components (e.g., graphics cards, additional RAM, storage drives).
  • **BIOS Settings**: Familiarize yourself with basic BIOS settings. Incorrect settings can lead to system instability or prevent booting.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.