DAKEFPV H743 FC 6S 55A STACK 4IN1 Blheli_S Bluejay 8bit ESC

Contents

DAKEFPV H743 Flight Controller and 4-in-1 ESC Stack User Manual

Model: H743 FC 6S 55A STACK 4IN1 Blheli_S Bluejay 8bit ESC

Brand: DAKEFPV

1. Introduction

This manual provides detailed instructions for the installation, configuration, and operation of your DAKEFPV H743 Flight Controller (FC) and 4-in-1 Electronic Speed Controller (ESC) Stack. Designed for FPV drones, this high-performance stack supports various configurations including 6S and 8S setups, and is compatible with popular firmware like Betaflight and Ardupilot.

The DAKEFPV H743 FC features a powerful STM32H743 main control chip, 16MB onboard FLASH memory for black box logging, a built-in barometer, and dual independent BECs. The accompanying 4-in-1 ESC offers robust power delivery with options up to 70A, utilizing Blheli_S Bluejay 8bit firmware for smooth and reliable motor control.

Video 1: DAKEFPV H743 8S 70A Stack Product Overview

2. Package Contents

Please verify that all items listed below are included in your package. Contents may vary slightly based on the specific stack option purchased.

Option 1: DAKEFPV H743 70A 30x30 STACK

Package contents for DAKEFPV H743 70A 30x30 STACK

Image 1: Package Contents for H743 70A 30x30 STACK

  1. DAKEFPV H743 Flight Controller x 1
  2. DAKEFPV BLS 70A 4 in 1 ESC x 1
  3. 35V 1000uF Low ESR Capacitor x 1
  4. M3 Nylon Nut x 5
  5. M3 silicone O Ring x 5
  6. M3*8mm Silicone Grommets (for FC) x 1
  7. M3*8.1mm Silicone Grommets (for ESC) x 1
  8. SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  9. SH 1.0mm 75mm-length 8pin Cable x 1
  10. M3*30mm Inner-hexagon Screws x 5
  11. GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  12. XT60 Power Cable (70mm) x 1

*When the ESC tail faces the drone's front, use the 25mm-length 8pin cable for FC and ESC connection; both ends plug interchangeably.

Option 2: DAKEFPV H743 70A 30x30 FC (Flight Controller Only)

Package contents for DAKEFPV H743 70A 30x30 FC

Image 2: Package Contents for H743 70A 30x30 FC

  1. DAKEFPV H743 Flight Controller x 1
  2. Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone O rings x 5
  3. FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  4. GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3: DAKEFPV 8S 70A 4 in 1 ESC (ESC Only)

Package contents for DAKEFPV 8S 70A 4 in 1 ESC

Image 3: Package Contents for 8S 70A 4 in 1 ESC

  1. DAKEFPV 8S 70A 4 in 1 ESC x 1
  2. 35V 1000uF Low ESR Capacitor (Buy 12S ESC Send 63V1000uF Capacitor)
  3. FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  4. XT60 x 1

3. Specifications

DAKE H743 30x30 Flight Controller

Specifications table for DAKE H743 30x30 Flight Controller

Image 4: DAKE H743 Flight Controller Specifications

FeatureSpecification
Main Control ChipSTM32H743
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENo
WiFiNot supported
DJI Air Unit ConnectionSupports 6-pin plug and wiring methods
6-pin DJI Air Unit Direct PlugCompatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wiring changes needed.
FLASH (Black Box)16MB
Current SensorSupported
Input Voltage3-8S LiPo battery
UART Serial Ports8 groups
Buzzer Solder PadSupports BZ+, BZ- solder pads for buzzer
BOOT ButtonPress BOOT button while powering up to force DFU mode for firmware flashing.
RSSI Solder PadSupported, located on the front RS solder pad
SmartPort/F.PortNot supported
Supported Flight Control TypesBetaFlight (default firmware), Ardupilot
Target NameDAKEFPVVH743
Mounting Hole30.5 x 30.5 mm (4mm holes)
Size36 x 36 x 8 mm
Weight10.5g

DAKE 12S 70A 4-in-1 ESC

Specifications table for DAKE 12S 70A 4-in-1 ESC

Image 5: DAKE 12S 70A 4-in-1 ESC Specifications

FeatureSpecification
Product NameDAKE 12S 70A 4 in 1 ESC
FirmwareBLHeli_S / BlueJay
Battery Input3-8S LiPo battery
Continuous Current70A x 4
Maximum Current80A x 4 - 10s
Built-in TVS DiodeYes
External Capacitor1000uF high frequency low resistance capacitor (included in package)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Input Voltage3-8S LiPo battery
Output VoltageVBAT
Current SensorSupported (Scale=400, Offset=0)
TelemetryNot supported
Mounting Hole30.5 x 30.5 mm (4mm holes)
Size45.4*42.8*6.5mm
Weight23.5g

General Product Properties

  • Size: 30 X 30 mm
  • Material: Composite Material
  • Origin: Mainland China
  • Recommend Age: 14+y
  • Use: Vehicles & Remote Control Toys
  • Is Electric: No Battery
  • Is Batteries Included: No

4. Key Features

  • Powerful H743 Flight Controller: Equipped with STM32H743 main control chip for superior performance.
  • Integrated 4-in-1 ESC: Robust 70A continuous current per channel (80A peak for 10s) with Blheli_S Bluejay 8bit firmware.
  • Dual Gyroscopes: Features ICM42688P for enhanced flight stability and precision.
  • Built-in Barometer: Senses aircraft altitude in real-time.
  • 16MB Black Box Flash: Continuously records flight status, sensor data, control commands, and fault codes for accident analysis.
  • Dual Independent BECs: 12V 3A + 5V 3A for reliable power to peripherals.
  • 8 UARTs: Ample serial ports for various connections (receiver, GPS, VTX, camera).
  • DJI Air Unit Direct Plug Interface: Compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 without needing wiring changes.
  • Supports 8 Motors: Can be used for X8, Y6, fixed-wing, and other aircraft models requiring more than 4 motors.
  • LED Light Bar Pads: Easily connect and control LED strips for customization.
  • LiPo Battery Capacity Indicator: Onboard 4-level indicator for quick battery status checks.
  • Advanced Filtering: TVS protection diode and 21 imported Japanese TDK SMD filter capacitors + 1000uF ultra-large capacity capacitor for clean power.
Diagram showing various features like Barometer, Black box, DJI Air Unit direct plug, BEC, 8x URAT, GPS, LED pads
Image 6: Overview of FC Features
Diagram highlighting dual ICM42688P gyroscopes and LDO power supply chip
Image 7: Dual Gyroscope and Clean Power Supply
Diagram showing TVS diode and filter capacitors for power filtering
Image 8: TVS Diode and Filter Capacitors
Diagram showing 4-level battery capacity indicator on the flight controller
Image 9: Onboard LiPo Battery Capacity Indicator

5. Setup and Installation

5.1 General Stack Installation Note

Important Stack Installation Note regarding spacing and silicon pads

Image 10: Important Stack Installation Note

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings in your flight control software. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.

It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

It is strongly recommended to use the Low ESR capacitor included in the package to prevent the stack from being burnt out by voltage spikes on powering up.

5.2 Wiring Diagram

Refer to the comprehensive wiring diagram below for connecting your flight controller, ESC, motors, and other peripherals.

Detailed wiring diagram for DAKEFPV H743 FC and 4-in-1 ESC stack, showing connections to motors, receiver, VTX, GPS, camera, and LED

Image 11: Full Wiring Diagram for FC & Motors and Peripherals

The FC and ESC can also be connected via direct soldering. Refer to the pinout diagrams for the H743 Flight Controller and BLS 70A 4-in-1 ESC for specific solder pad definitions.

Pinout layout for the H743 Flight Controller, showing various pads like GND, 12V, CAM, OSD, BAT, USB, VTX, RSSI, LED, GPS, ELRS, Gyro
Image 12: H743 Flight Controller Layout (Pinout)
Layout for the BLS 70A 4-in-1 ESC, showing motor pads (MOTOR 1-4) and power connections
Image 13: BLS 70A 4-in-1 ESC Layout (Motor Pads)

5.3 Connecting DJI Air Units

The DAKEFPV H743 FC is designed for easy integration with DJI Air Units. Use the provided 6-pin cable for connection.

Use the 6-pin cable that comes with the H743 stack (accessory No.11 in the package section).

Diagram showing cable connection between H743 FC and RunCam Link/Caddx Vista Air Unit

Image 14: Connection to RunCam Link/Caddx Vista Air Unit

5.3.2 Cable Connection vs DJI Air Unit V1

Use the 6-pin cable that comes with the H743 stack (accessory No.11 in the package section).

Diagram showing cable connection between H743 FC and DJI Air Unit V1, with a warning about SBUS disconnection for ELRS receivers

Image 15: Connection to DJI Air Unit V1

5.3.3 Cable Connection vs DJI O3 Air Unit

Use the 6-pin cable that comes with the O3 Air Unit.

Diagram showing cable connection between H743 FC and DJI O3 Air Unit

Image 16: Connection to DJI O3 Air Unit

6. Operating Instructions

6.1 Flight Control Software

The DAKEFPV H743 FC supports Betaflight (default firmware) and Ardupilot. Connect the FC to your computer via the USB Type-C port and use the respective configurator software for setup, tuning, and firmware updates.

  • Betaflight: Download the Betaflight Configurator from the official Betaflight GitHub page.
  • Ardupilot: Refer to the Ardupilot documentation for setup and configuration.

To enter DFU mode for firmware flashing, press and hold the BOOT button while connecting the FC to your computer.

6.2 LED Light Bar Pads

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode, and short presses of the BOOT button let you toggle between various preset light effects.

Diagram showing LED light bar pads on the flight controller and an example LED strip

Image 17: LED Light Bar Pads Connection

6.3 LiPo Battery Capacity Indicator

On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on goggles to check the battery status.

7. Maintenance

  • Keep the flight controller and ESC clean and free from dust and debris.
  • Regularly inspect all solder joints and connections for any signs of damage or corrosion.
  • Ensure proper ventilation to prevent overheating, especially during intensive flight.
  • Avoid exposing the components to moisture or extreme temperatures.
  • Periodically check for firmware updates for both the FC (Betaflight/Ardupilot) and ESC (Bluejay/BLHeli_S) to ensure optimal performance and access to new features.

8. Troubleshooting

8.1 ELRS Receiver Not Recognized with DJI Air Unit

Warning diagram for ELRS receiver and DJI Air Unit V1 connection, showing the SBUS wire to disconnect

Image 18: Importance Notice for SBUS Receiver with DJI Air Unit

When using an SBUS receiver (such as ELRS) simultaneously with a DJI Air Unit (O3/Link/Vista/Air Unit V1), some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness.

You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller.

DO NOT connect this wire to assure the external SBUS receiver works properly!

8.2 Stack Burnt Out by Voltage Spikes

To prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package. Ensure it is correctly soldered to the BAT+ and GND pads as shown in the wiring diagrams.

Diagram showing capacitor connection to BAT+ and GND pins

Image 19: Capacitor Connection Diagram

9. User Tips

  • Firmware Updates: Always keep your FC and ESC firmware updated to the latest stable versions for best performance and bug fixes.
  • Capacitor Installation: Do not skip installing the provided Low ESR capacitor. It is crucial for protecting your electronics from voltage spikes.
  • Wiring Cleanliness: Keep your wiring as neat and short as possible to minimize electrical noise and potential interference.
  • Test Before Flight: After any changes or new installations, always perform thorough bench testing and a short hover test before full flight.
  • SBUS with DJI Air Unit: If using an ELRS receiver with a DJI Air Unit, remember to disconnect the SBUS wire from the Air Unit harness to avoid recognition issues.

10. Support

For further assistance, technical support, or warranty inquiries, please contact DAKEFPV customer service through the platform where you purchased the product. Ensure you have your product model and purchase details ready.

Please note that damage resulting from improper installation, modification, or misuse of the product is not covered under warranty.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.