DAKEFPV H743

Contents

DAKEFPV H743 Flight Controller and 120A 4-in-1 ESC Stack Instruction Manual

Model: H743

Thank you for choosing DAKEFPV. This manual provides essential information for the proper installation, setup, and operation of your H743 Flight Controller and 120A 4-in-1 ESC Stack.

1. Product Overview

The DAKEFPV H743 Flight Controller and 120A 4-in-1 ESC Stack is a high-performance solution designed for FPV drones, supporting up to X8 FPV configurations with 8 motors. It features robust power delivery and advanced flight control capabilities.

DAKEFPV H743 120A 30.5x30.5 Stack overview with key features
Figure 1: DAKEFPV H743 Stack with highlighted features.

Key Features:

  • Flight Controller (FC):
    • Main Control Chip: STM32H743
    • Gyroscope: Dual ICM42688P
    • Built-in 16MB high-speed FLASH for black box recording (flight status, sensor data, control commands, fault codes for accident analysis).
    • Built-in barometer for real-time altitude sensing.
    • Supports 8 motors and 4 servos, suitable for X8/Y6/fixed-wing aircraft.
    • 12V 3A + 5V 3A Dual-channel BEC.
    • Support 8 UARTs.
    • GPS module powered by 5.0V.
    • DJI Air Unit direct plug interface (fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1).
    • LED light bar pads with customizable lighting modes (single press BOOT button for modes, long press for onboard LED effect, short presses to toggle effects).
    • 4-level battery capacity indicator on the FC.
  • Electronic Speed Controller (ESC):
    • Continuous Current: 120A x 4
    • Peak Current: Up to 125A (realistic output)
    • Improved MOS transistors and TVS protection tube.
    • Large pad design for simple welding.
    • 21 imported Japanese TDK SMD filter capacitors + 1000uF ultra-large capacity for signal filtering.
    • Aluminum alloy heat sink for stable electronic speed controller output.
DAKE H743 BLS 120A STACK features summary
Figure 2: Summary of DAKEFPV H743 BLS 120A Stack features.

2. Specifications

H743 Flight Controller

Feature Specification
Product NameDAKE H743 30 x 30 Flight Controller
Main ControlSTM32H743
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENone
WIFINot supported
DJI Air Unit ConnectionSupports 6-pin plug-in, two wiring methods
6-pin DJI Air Unit direct plugSupported, fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wiring changes needed
FLASH16MB
Installation Hole30.5 x 30.5 (4mm holes)
Size36 x 36 x 8 mm
Weight10.5g

BLS 120A 4-in-1 ESC

Feature Specification
Product NameDAKE 12S 120A 4 in 1 ESC
FirmwareBLHELI_S
Battery Input3-12S LiPo
Continuous Current120A x 4
Max Current80A x 4 (10 seconds)
Built-in TVSYes
External Capacitor1000uF high-frequency low-ESR capacitor (included)
ESC ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Current SensorYes (Scale=400, Offset=0)
TelemetryNot supported
Installation Hole30.5 x 30.5 (4mm holes)
Size45.4 x 42.8 x 6.5 mm
Weight23.5g
Specifications table for DAKE H743 Flight Controller and 12S 120A 4 in 1 ESC
Figure 3: Detailed specifications for the Flight Controller and ESC.

3. Package Contents

The DAKEFPV H743 120A 30x30 Stack comes with the following components:

Package contents for DAKEFPV H743 120A 30x30 Stack
Figure 4: Contents of the DAKEFPV H743 120A 30x30 Stack package.
  1. DAKEFPV H743 Flight Controller x 1
  2. DAKEFPV BLS 120A 4 in 1 ESC x 1
  3. 35V 1000uF Low ESR Capacitor x 1
  4. M3 Nylon Nut x 5
  5. M3 silicone O Ring x 5
  6. M3*8mm Silicone Grommets (for FC) x 1
  7. M3*8.1mm Silicone Grommets (for ESC) x 1
  8. SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  9. SH 1.0mm 75mm-length 8pin Cable* x 1
  10. M3*30mm Inner-hexagon Screws x 5
  11. GPS 6-pin cable, Analog VTX 6-pin cable, dual-camera 6-pin cable x 1
  12. XT60 Power Cable (70mm) x 1

*When the ESC tail faces the drone's front, use this cable for the flight controller.

4. Setup and Installation

Stack Assembly

When assembling the flight controller and ESC, ensure proper spacing and orientation. The orientation of the gyroscope and motor sequence can be adjusted through software settings. If you choose an inverted mounting method, pay close attention to the space between the frame, the FC, and the ESC.

Diagram showing critical spacing during stack installation
Figure 5: Ensure sufficient space between components during stack installation.

It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Any damage resulting from improper installation of this nature is not covered under the Warranty.

Dimensions of the H743 Flight Controller and ESC stack
Figure 6: Dimensions of the H743 Flight Controller and ESC.

5. Wiring Diagrams

Refer to the following diagrams for correct wiring of your DAKEFPV H743 stack with various components.

H743 Flight Controller layout diagram showing all pads and connections
Figure 7: H743 Flight Controller Layout (Top and Bottom).
BLS 120A 4-in-1 ESC layout with motor connections
Figure 8: BLS 120A 4-in-1 ESC Layout with Motor Connections.
Comprehensive wiring diagram for the DAKEFPV H743 stack with various peripherals
Figure 9: Comprehensive Wiring Diagram.

Capacitor Connection

To prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package. The FC and ESC can also be connected via direct soldering.

TVS diode and capacitor details for power protection
Figure 10: TVS Diode and Capacitor for Power Protection.

DJI Air Unit Connection

The H743 Flight Controller supports direct plug-in connection with DJI O3/Link/Vista/Air Unit V1 using the provided 6-pin cable.

Cable connection diagram for DJI O3 Air Unit
Figure 11: Cable Connection to DJI O3 Air Unit.
Cable connection diagram for DJI Air Unit V1
Figure 12: Cable Connection to DJI Air Unit V1.

ELRS and SBUS Receiver Connection Notes

For ELRS receivers, we recommend connecting the receiver's TX and RX to the T2 and R2 pads on the flight controller.

Important notice for SBUS receiver: When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).

Warning about SBUS receiver connection and wire disconnection for DJI Air Unit
Figure 13: SBUS Receiver Connection Warning.

If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully. DO NOT connect this wire to assure the external SBUS receiver work properly!

6. Operation

LED Light Bar Control

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode, and short presses of the BOOT button let you toggle between various preset light effects.

Diagram showing connection to LED light bar pads
Figure 14: LED Light Bar Pad Connection.

Battery Capacity Indicator

The flight controller features a convenient 4-level battery capacity indicator. Once the battery is connected, you can instantly see the battery level, eliminating the need for an external LiPo checker.

4-level battery capacity indicator on the Flight Controller
Figure 15: 4-Level Battery Capacity Indicator.

Firmware Flashing

The BOOT button on the flight controller can be used to force the device into DFU mode for firmware flashing. Press and hold the BOOT button while connecting power to the FC to enter DFU mode.

7. Maintenance

  • Keep the flight controller and ESC clean and free from dust and debris.
  • Avoid exposing the components to moisture or extreme temperatures.
  • Regularly inspect all solder joints and connections for any signs of wear or damage.
  • Ensure all screws are tightened appropriately, but do not overtighten to avoid damaging the boards.
  • Store the stack in a dry, anti-static environment when not in use.

8. Troubleshooting

  • ELRS Receiver Not Recognized with DJI Air Unit: If you are using an ELRS receiver simultaneously with a DJI Air Unit (O3/Link/Vista/Air Unit V1) and encounter recognition issues, you may need to disconnect the SBUS signal wire from the Air Unit harness. Carefully use tweezers to remove or cut and insulate the SBUS wire from the 6-pin harness connector.
  • SBUS Receiver Issues: Ensure the SBUS signal wire from your SBUS receiver is connected to the dedicated SBUS pad on the front side of the flight controller. This pad uses UART2 internally.
  • No Power/Intermittent Power: Check all power connections, especially the XT60 power cable and the Low ESR capacitor. Ensure the capacitor is correctly installed to prevent voltage spikes.
  • Flight Controller Not Responding: Try reflashing the firmware using the DFU mode (hold BOOT button while connecting power). Verify all signal cables between the FC and ESC are securely connected.
  • Motor Issues: Check motor connections to the ESC. Ensure ESC firmware is compatible and properly configured.

9. User Tips

  • Always double-check your wiring against the diagrams before applying power to avoid damage.
  • Utilize the built-in 16MB black box flash for flight data recording, which can be invaluable for diagnosing issues after a crash or unexpected event.
  • Take advantage of the 4-level battery indicator on the FC for quick battery status checks during setup and pre-flight.
  • When soldering, ensure clean and strong connections, especially for power leads, to prevent intermittent issues or component failure.

10. Warranty and Support

For warranty information and technical support, please contact your retailer or the DAKEFPV customer service directly. Keep your proof of purchase for any warranty claims. Damage due to improper installation, such as incorrect spacing between FC and ESC leading to short circuits, may void your warranty.

11. Product Video

Watch this video for a visual overview of the DAKEFPV H743 12S 120A Stack.

Video 1: DAKEFPV H743 12S 120A Stack Product Overview.

© 2024 DAKEFPV. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.