SUMRY SP/EP Hybrid Solar Inverter Series

Contents

SUMRY SP/EP Hybrid Solar Inverter Series User Manual

Models: SP-2200, SP-3200, SP-4200, SP-7000, EP-4200H

About This Manual

This manual provides instructions for the assembly, installation, operation, and troubleshooting of the SUMRY SP/EP Hybrid Solar Inverter. Please read it carefully before installation and operation.

Target Group

This manual is designed for both professionals and end-users. End-users can handle operations that do not require specific skills. Professionals should possess the following qualifications:

  • Understanding of inverter operation.
  • Knowledge of handling crises and risks associated with electrical equipment.
  • Ability to install and commission electrical equipment and fixtures.
  • Familiarity with applicable standards and directives.
  • Adherence to this manual and all safety knowledge.

Safety Regulations

Warning: This article contains important safety and operation instructions. Please read and save this manual for future reference.

  1. Always select the appropriate battery setting (lead-acid or lithium) to ensure normal system operation.
  2. Read all instructions and cautions on the unit and in this manual before use.
  3. Never short-circuit AC output and DC input. Do not connect to mains when DC input is short-circuited.
  4. Do not charge non-rechargeable batteries.
  5. Do not disassemble the unit. For maintenance or repair, send it to a professional technical service center. Incorrect reassembly can lead to electric shock or fire.
  6. To reduce electric shock risk, disconnect all wiring before maintenance or cleaning. Turning off the device alone is not sufficient.
  7. Exercise extreme caution with metal tools near batteries to prevent short circuits or sparks that could cause explosions.
  8. Use appropriate cable sizes for battery connections to ensure optimal operation and safety.
  9. Strictly follow installation procedures when disconnecting AC or DC terminals.
  10. Connect the inverter to a permanent grounding wiring system, complying with local requirements.
  11. Provide a fuse that meets specifications for battery power supply overcurrent protection.
  12. Warning: Only professional service personnel should repair this equipment. If troubleshooting fails, return the inverter to the local dealer or service center.

Product Overview

The SUMRY SP/EP Hybrid Solar Inverter is a multifunctional off-grid solar inverter, integrating an MPPT solar charging controller, high-frequency pure sine wave inverter, and UPS function module. It is ideal for off-grid backup power and self-use systems. Its high-frequency transformer design allows for reliable power conversion in a compact size.

Features

  • Pure sine wave output inverter.
  • Supports two battery voltage modes: up to 2300W in 12V battery mode and 4200W in 24V battery mode.
  • Selectable utility grid input voltage range based on load requirements (household appliances/personal computers).
  • Adjustable charging current via LCD based on battery requirements.
  • Simultaneous powering of loads by solar energy and utility grid.
  • AC input compatible with mains and generators.
  • Automatic restart function upon mains power restoration.
  • Overload, over-temperature, and short-circuit protection.
  • Intelligent battery charging design for optimized battery life.
  • RS485 port for BMS communication.
  • Cold start function.
  • Built-in MPPT with an operating voltage range of 55V~500V and open circuit voltage of 500Voc.
  • Optional WIFI remote monitoring via mobile app or website.
  • Optional RGB lamp indicating inverter status with different colors.

Basic System Architecture

The inverter/charger can be integrated into a system with photovoltaic modules, a generator or utility grid, and batteries. Consult your system integrator for specific configurations. This inverter can power various home and office appliances, including motor-type appliances like tube lights, fans, refrigerators, and air conditioners.

Hybrid Power System Diagram
Figure 1: Hybrid Power System. Shows solar modules, generator/utility, inverter, battery packs, and home appliances connected. Note: This inverter must work with battery; ensure battery connection before solar panels.

Product Components Overview

The inverter features an LCD screen, status indicators, and function keys for operation and display. The rear panel includes various connection ports.

Product Overview Diagram with Labeled Ports
Figure 2: Product Overview. 1. LCD display, 2. Status indicator, 3. Charging indicator, 4. Fault indicator, 5. Function buttons, 6. Power on/off switch, 7. AC input, 8. AC output, 9. PV input, 10. Battery input, 11. Circuit breaker, 12. Ground wire terminal, 13. BMS communication port, 14. RS-232 communication port.

Setup (Installation)

Unpacking and Inspection

Upon receiving the inverter, unpack it and inspect for any damage. The package should contain:

  • Machine x 1
  • User manual x 1

Preparation Before Installation

Before connecting any wiring, remove the bottom cover of the inverter by unscrewing two screws.

Mounting the Unit

Consider the following points for installation:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install the inverter at eye level for easy reading of the LCD display.
  • Allow a clearance of approximately 20 cm to the sides and 50 cm above and below the unit for proper air circulation and heat dissipation.
  • The ambient temperature should be between 0°C and 55°C for optimal operation.
  • Install vertically against the wall, ensuring sufficient space for wiring.

Caution: Suitable for mounting on concrete or other non-combustible surfaces only.

Tighten the screws to fix the installation. M4 or M5 screws are recommended.

Inverter Mounting Diagram
Figure 3: Mounting the Unit. Shows recommended clearances: 20cm to sides, 50cm above and below.

Battery Connection

Warning: An independent DC overcurrent protector or disconnect device between the battery and inverter is required. All wiring must be performed by qualified personnel. Use appropriate cables for safety and efficient operation.

ModelWire SpecificationTorque Value
12V1 * 2/0 AWG (67mm²)2-3 Nm
24V1 * 1/0 AWG (54mm²)2-3 Nm

Note: The recommended charging current for lead-acid batteries is 0.2C (C is battery capacity).

Lead-Acid Battery Connection Steps:

  1. Connect the battery using recommended cable specifications.
  2. Connect all battery packs as needed.
  3. Insert the ring terminal of the battery cable into the inverter's battery connector and tighten bolts to 2-3 Nm. Ensure correct polarity.
  4. Connect all battery packs as shown in the diagram below.
Battery Connection Diagram
Figure 4: Battery Connection. Shows wiring for 12V and 24V battery models.

Lithium Battery Connection and Setting:

Only lithium batteries matched with BMS communication protocol are allowed. Follow these steps:

  1. Connect the battery using recommended cable specifications.
  2. Insert the ring terminal of the battery cable into the inverter's battery connector and tighten bolts to 2-3 Nm. Ensure correct polarity.
  3. Connect one side of an RJ45 cable to the inverter's BMS communication port.
  4. Insert the other side of the RJ45 cable into the RS485 communication port on the lithium battery.

Note: If using a lithium battery, ensure the battery and inverter are connected with a BMS communication cable, and select "LIB" mode in the inverter settings.

BMS Communication Port PIN Definition:
Pin NumberPort Definition
1RS485B
2RS485A
3-6NC (No Connection)
7RS485A
8RS485B

To communicate with the lithium battery BMS, press and hold the "ENTER" button, then set the battery type to "LIB" in program 05. Select the matching battery protocol in program 10.

AC Input/Output Connection

Caution: Install a separate AC breaker between the inverter and the AC input power source. This ensures safe disconnection during maintenance and protection from overcurrent. There are two terminal blocks labeled "IN" and "OUT"; do not mis-connect them. All wiring must be performed by qualified personnel. Use appropriate cable sizes.

Suitable Cable Specifications for AC Wires:

ModelWire GaugeTorque Value
12V/24V1 * 12 AWG1.2-1.6 Nm

AC Input/Output Connection Steps:

  1. Before connecting, open the DC protector or disconnector.
  2. Remove 10mm of insulation from the six conductors. Shorten phase L and neutral conductor N by 3mm.
  3. Insert AC input wires according to polarities (L, N) on the terminal block and tighten screws. Connect the PE protective conductor (ground, yellow-green) first.
  4. Insert AC output conductors according to polarities and tighten screws.
  5. Ensure all wires are firmly connected.

Caution: Ensure all AC cables are connected correctly according to polarity. Appliances like air conditioners require 2-3 minutes to restart; a power shortage and quick recovery can damage them. Check the manufacturer's instructions for such appliances.

PV Connection

Caution: Install a separate DC circuit breaker between the inverter and the PV module. All wiring must be performed by qualified personnel. Use appropriate cables for safety and efficient operation.

PV Module Selection:

When selecting PV modules, consider these parameters:

  • Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the inverter.
  • Open circuit Voltage (Voc) of PV modules should be higher than the minimum battery voltage.
ParameterValue
Max. PV Array Power4000W
I Max. PV18A
Nominal PV Voltage240V
PV Array MPPT Voltage Range55V-500V
Max. PV Array Open Circuit Voltage500V

PV Module Connection Steps:

  1. Remove 10mm of insulation from positive and negative conductors.
  2. Check correct polarity of connection cables from PV modules and PV input connectors. Connect positive (+) to positive (+) and negative (-) to negative (-).
  3. Ensure wires are securely connected.

Final Assembly

After connecting all wires, replace the bottom cover and secure it with screws.

Operating

Power On/Off

After correctly installing the machine and connecting the battery, simply press the On/Off switch to turn on the inverter.

Operation and Display Panel

The front panel of the inverter features an LCD display, LED indicators, and four function keys (ESC, UP, DOWN, ENTER) to show operation status and input/output power information.

Operation and Display Panel
Figure 5: Operation and Display Panel. Shows LCD display, LED indicators, and function keys (ESC, UP, DOWN, ENTER).

RGB Light (Optional)

The RGB light indicates inverter status:

  • Green light: Inverter state.
  • Blue light: Utility state.
  • Red light: Failure state.

LED Indicator

LED IndicatorColorStatusMessages
AC / INVGreenSolid OnOutput is powered by utility in Line mode.
FlashingOutput is powered by battery or PV in battery mode.
CHGGreenSolid OnBattery is fully charged.
FlashingBattery is charging.
FAULTRedSolid OnFault occurs in the inverter.
FlashingWarning condition occurs in the inverter.

Function Keys

Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

LCD Display Icons

LCD Display Icons Description
Figure 6: LCD Display Icons. Provides a visual guide to the various icons and their meanings on the inverter's LCD screen, including PV input, AC input, battery level, load level, and fault indicators.

LCD Setting

To enter setting mode, press and hold the "ENTER" button for 3 seconds. Use "UP" or "DOWN" to select programs, and "ENTER" to confirm or "ESC" to exit. Key settings include:

  • 01 Output Source Priority: Configure whether solar, battery, or utility takes priority for powering loads.
  • 02 Maximum Charging Current: Set total charging current for solar and utility chargers.
  • 03 AC Input Voltage Range: Select acceptable AC input voltage range (e.g., 90-280VAC for appliances, 170-280VAC for UPS).
  • 04 Power Saving Mode: Enable or disable power saving mode.
  • 05 Battery Type: Select battery type (AGM, Flooded, User Defined, Lithium).
  • 06 Auto Restart When Overload Occurs: Enable or disable auto restart after overload.
  • 07 Auto Restart When Over Temperature Occurs: Enable or disable auto restart after over temperature.
  • 08 Output Voltage: Set output voltage (e.g., 220V, 230V, 240V).
  • 09 Output Frequency: Set output frequency (50Hz, 60Hz).
  • 10 Lithium Battery Protocol: Select matching protocol for lithium batteries (e.g., PYLON, PACE).
  • 11 Maximum Utility Charging Current: Set maximum charging current from utility.
  • 12 Setting Voltage Point Back to Utility Charging: Configure voltage thresholds for switching to utility charging.
  • 13 Set Voltage Point Back to Battery Discharge: Configure voltage thresholds for switching back to battery discharge.
  • 16 Charger Source Priority: Configure charger source priority (Solar first, Solar and Utility, Only Solar).
  • 18 Alarm Control: Turn alarm on or off.
  • 19 Auto Return to Default Display Screen: Enable or disable automatic return to default display.
  • 20 Backlight Control: Turn backlight on or off.
  • 22 Beeps While Primary Source is Interrupted: Enable or disable beeps.
  • 23 Overload Bypass: Enable or disable bypass to line mode during overload in battery mode.
  • 25 Record Fault Code: Enable or disable fault code recording.
  • 26 Bulk Charging Voltage (C.V voltage): Set bulk charging voltage.
  • 27 Floating Charging Voltage: Set floating charging voltage.
  • 29 Low DC Cut-off Voltage: Set low DC cut-off voltage.
  • 33 Battery Equalization: Enable or disable battery equalization.
  • 34 Battery Equalization Voltage: Set battery equalization voltage.
  • 35 Battery Equalized Time: Set duration for battery equalization.
  • 36 Battery Equalized Timeout: Set timeout for battery equalization.
  • 37 Equalization Interval: Set interval for battery equalization.
  • 39 Equalization Activated Immediately: Activate equalization immediately.
  • 48 RGB Lighting: Turn RGB lights on or off.

Maintenance

Clearance and Maintenance for Anti-Dust Kit (Optional)

The inverter comes with a factory-installed anti-dust kit. This kit automatically detects and adjusts the internal thermal sensor to maintain internal temperature, prevents dust ingress, and enhances product reliability in harsh environments.

Maintenance Steps:

  1. Remove the screws securing the air filter cover.
  2. Remove the air filter.
  3. Clean the air filter.
  4. After cleaning, reinstall the dust removal net and secure the cover.

Notice: The anti-dust kit should be cleaned from dust every one month.

Troubleshooting

This section provides guidance for common issues. For persistent problems, contact professional service personnel.

Battery Alarm Codes

Alarm CodeAlarm EventIcon Flashing
21Battery Cell Over Voltage(21)
22Battery Cell Under Voltage(22)
23Battery Pack Over Voltage(23)
24Battery Pack Under Voltage(24)
25Charging Over Current(25)
26Discharging Over Current(26)
27Charging Cell Over Temperature(27)
28Discharging Cell Over Temperature(28)
29Charging Cell Under Temperature(29)
30Discharging Cell Under Temperature(30)
34Battery capacity is too low(34)
44Battery Cell Voltage Imbalance(44)
45Battery Cell Temperature Imbalance(45)
46Internal Communication Alarm(46)

Battery Fault Codes

Fault CodeFault EventIcon
21Battery Cell Over Voltage(21) ERROR
22Battery Cell Under Voltage(22) ERROR
23Battery Pack Over Voltage(23) ERROR
24Battery Pack Under Voltage(24) ERROR
25Charging Over Current(25) ERROR
26Discharging Over Current(26) ERROR
27Charging Cell Over Temperature(27) ERROR
28Discharging Cell Over Temperature(28) ERROR
29Charging Cell Under Temperature(29) ERROR
30Discharging Cell Under Temperature(30) ERROR
31Ambient Over Temperature(31) ERROR
32Ambient Under Temperature(32) ERROR
33MOS Over Temperature(33) ERROR
35Battery Short Circuit(35) ERROR
36Charge Overvoltage(36) ERROR
37System Failure(37) ERROR
39Charging MOS Fault(39) ERROR
40Discharge MOS Fault(40) ERROR
41Temperature Sensor Fault(41) ERROR
42Battery Cell Fault(42) ERROR
43Sampling Communication Failure(43) ERROR

Warning Codes

Warning CodeWarning EventAutomatic AlarmIcon Flashing
01Fan is locked when inverter is on.Beep three times every second(01)
03Battery overchargeBeep once every second(03)
04Battery low voltageBeep once every second(04)
07OverloadBeep once every 0.5 second(07)
10Output power is deratingBeep twice every 3 seconds(10)
15PV energy is weakNo Beep(15)
EQBattery equalizationNo Beep(EQ)

General Troubleshooting Table

ProblemLCD/BuzzerExplanation / Possible CauseWhat to do
Unit shuts down automatically during startup process.LCD and buzzer active for 3 seconds, then off.Battery voltage is too low1. Re-charge battery. 2. Replace battery.
No response after power on.No indication.1. Battery voltage too low. 2. Battery polarity reversed.1. Check batteries and wiring. 2. Re-charge battery. 3. Replace battery.
Input voltage displayed as 0 on LCD.Input protector trippedCheck if AC breaker is tripped and AC wiring is connected.
Mains exist but unit works in battery mode.Power-on icon of LCD flashes, status indicator icon flashes.Insufficient quality of AC power (shore or generator)1. Check if AC wires are too thin/long. 2. Check if generator (if applied) is working or if input voltage range setting is correct (UPS → Appliance).
Fault code 07Overload error. Inverter overloaded 110%, time is up.Reduce the connected load by switching off some equipment.
Fault code 05Output short circuited.Check if wiring is connected well and remove abnormal load.
Fault code 02Internal temperature of inverter component overheated.Check whether air flow is blocked or ambient temperature is too high.
Buzzer beeps continuously and status indicator icon is always on.Fault code 03Battery is over-charged. Battery voltage too high.Return to repair center. Check if spec and quantity of batteries meet requirements.
Fault code 01Fan faultReplace the fan.
Fault code 06/58Output abnormal1. Reduce the connected load. 2. Return to repair center.
Fault code 08/09/53/57Internal components failed.Return to repair center.
Fault code 51Over current or surge.Restart the unit; if error persists, return to repair center.
Fault code 52Bus voltage too low.Restart the unit; if error persists, return to repair center.
Fault code 55Output voltage unbalanced.Restart the unit; if error persists, return to repair center.

Specifications

The SUMRY SP/EP Hybrid Solar Inverter is available in various models, including SP-2200, SP-3200, SP-4200, SP-7000, and EP-4200H, offering different power capacities and features.

Model Specifications Table
Figure 7: Model Specifications. Details Rated Power, Max. PV Array Power, and Max. PV input current for SP-2200, SP-3200, SP-4200, and SP-7000 models.

Table 1: Specification of LINE Mode (EP-4200H)

ParameterSpecification
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS); 90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS); 100Vac±7V (Appliances)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionBattery mode: Electronic Circuits
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)

Table 2: Specification of Inverter Mode (EP-4200H)

ParameterSpecification
Rated Output PowerDC12V-2300VA/2300W; DC24V-4200VA/4200W
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency60Hz or 50Hz
Peak Efficiency94%
Overload Protection5s@≥150% load; 10s@105%~150% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage12 Vdc; 24Vdc
Cold Start Voltage11.5 Vdc; 23.0Vdc
Low DC Warning Voltage (@Load < 20%)11.0 Vdc; 22.0Vdc
Low DC Warning Voltage (@20% ≤ Load < 50%)10.7 Vdc; 21.4Vdc
Low DC Warning Voltage (@Load ≥ 50%)10.1 Vdc; 20.2Vdc
Low DC Warning Return Voltage (@Load < 20%)11.5 Vdc; 23.0Vdc
Low DC Warning Return Voltage (@20% ≤ Load < 50%)11.2 Vdc; 22.4Vdc
Low DC Warning Return Voltage (@Load ≥ 50%)10.6 Vdc; 21.2Vdc
Low DC Cut-off Voltage (@Load < 20%)10.5 Vdc; 21.0Vdc
Low DC Cut-off Voltage (@20% ≤ Load < 50%)10.2 Vdc; 20.4Vdc
Low DC Cut-off Voltage (@Load ≥ 50%)9.6 Vdc; 19.2Vdc
High DC Cut-off Voltage16 Vdc; 32Vdc
No Load Power Consumption20W; 30W
Saving Mode Power Consumption<10W; <15W

Table 3: Specification of Charging Mode

Utility Charging Mode12V24V
Battery ModelFlooded Battery
Charging Current (UPS) @Nominal Input Voltage100A
Bulk Charging14.629.2
Voltage (AGM / Gel Battery)14.128.2
Floating Charging Voltage13.5Vdc27Vdc
Charging Algorithm3-Step

Table 4: General Specifications

ParameterSpecification
Operating Temperature Range-20°C to 55°C
Storage Temperature-20°C~60°C
Dimension (D*W*H), mm405*305*108
Net Weight, kg6.7

Warranty and Support

All SUMRY products come with a 1-year warranty from the store. For any issues or repairs, please contact professional service personnel or the local dealer/service center. Do not attempt to disassemble the unit yourself.

A detailed user manual in PDF format is available for download: View User Manual (PDF)

User Tips

  • Battery Connection is Essential: This inverter requires a battery to operate. Ensure the battery is properly connected before connecting solar panels.
  • Check for Included WiFi Module: Some users have reported receiving a WiFi module even when ordering a 'without WiFi' configuration. Check your package contents.
  • Robust Build Quality: The inverter features a sturdy case made of thick metal, with good terminals and convenient connections, indicating a durable design.
  • Consider the Weight: The inverter is noted to be heavier than similar products, suggesting more robust internal components and heat dissipation features like larger radiators.
  • Initial Power-Up: The inverter can be started from the power supply alone, outputting 230 Volts at 50 Hz with a no-load power consumption of around 30 Watts.
  • Adjustable Charging Settings: The inverter allows for setting the charge current, for example, up to 80A in the settings.

Product Video

This video demonstrates the unboxing, an overview of the inverter's ports, and a practical demonstration of charging devices like phones and laptops, and powering household appliances such as a fan and a kettle using the SUMRY Hybrid Solar Inverter.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.