1. Introduction
Thank you for choosing the CNCEST Automatic Swing Door Opener. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new door opener. Please read these instructions carefully before installation and keep them for future reference.
This automatic swing door opener is designed for convenience and accessibility, featuring both manual and automatic operating modes, multiple access options (remote control, ID card, password, and switch), and a safety mechanism that detects obstructions. It is suitable for various door types and environments, supporting doors up to 220 lbs with a maximum opening angle of 120 degrees.
2. Package Contents
Before beginning installation, please verify that all components are present and undamaged:
- 1 x Automatic Swing Door Opener (Main Unit)
- 2 x Remote Controllers
- 2 x Switches
- 1 x Pull Arm
- 1 x Push Arm
- 5 x ID Cards
- 1 x Control Panel
- 1 x Sensor
- 1 x English RF Card Access Manual
- 1 x Chinese Installation Manual
- 1 x Chinese Sensor Manual
- All necessary accessories for assembly (screws, etc.)

3. Setup and Installation
This section provides step-by-step instructions for installing the Automatic Swing Door Opener. For a visual guide, please refer to the installation video below.
Installation Steps:
- Prepare the Main Unit: Use a screwdriver to gently pry open and remove the cover of the main unit.
- Mount the Base Plate:
- Identify the base plate. Ensure the side with the card slot faces upwards.
- Align the left side of the base plate with the center of the door hinge.
- Position the bottom edge of the base plate approximately 30mm from the top edge of the door opening.
- Mark the drilling points through the holes on the base plate.
- Drill the necessary holes and secure the base plate to the door frame using appropriate screws.
- Attach the Main Unit: Carefully hang the main unit onto the installed base plate. Secure it by tightening the eight fixing screws that connect the main unit to the base plate.
- Install the Pull Rod Fixing Plate (for pull-side installation):
- Align the top edge of the pull rod fixing plate with the top edge of the door.
- Position the plate approximately 160mm from the center of the door hinge.
- Mark the drilling points and secure the plate to the door.
- Attach the Pull Rod:
- Slide one end of the pull rod into the slide slot on the door.
- Attach the other end of the pull rod to the main unit.
- Tighten the screws to secure the pull rod in place.
- Install Slide Rail Outer Cover: Place the slide rail outer cover over the installed components. Ensure the side with the curved card slot faces upwards.
- Install End Caps: Attach the end caps to both sides of the slide rail to complete the assembly.
- Connect Power: Connect the power wires to the main unit. Note that the power wires are not polarity sensitive.
- Set Limit Block: Open the door to its maximum desired angle. Insert the limit block into the slide rail at this position and tighten its screw to fix the open limit.


4. Operating Instructions
The Automatic Swing Door Opener offers flexible operation through various methods and modes.
4.1. Access Methods

- Remote Control: Use the provided remote controllers to open and close the door from up to 15 meters (49 feet) away. The remote typically has buttons for Lock, Reset, Hold-Open, and Auto/Manual mode.
- ID Card: Swipe an authorized ID card on the control panel to open the door.
- Password: Enter a pre-set password on the control panel keypad to gain access.
- Wall Switch: Press the installed wall switch for quick and convenient entry/exit.
4.2. Operating Modes
- Automatic Mode: The door operates automatically based on sensor detection or input from the access methods.
- Manual Mode: In manual mode, the door can be opened with very low pressure and will close slowly, providing ease of use for individuals with limited mobility or those using wheelchairs.
4.3. Parameter Adjustment
The control panel allows for customization of various operating parameters:

- Opening Speed: Adjust the speed at which the door opens.
- Slow Opening Angle: Set the angle at which the door begins to slow down during opening.
- Closing Speed: Adjust the speed at which the door closes.
- Slow Closing Angle: Set the angle at which the door begins to slow down during closing.
- Hold Open Time: Configure how long the door remains open before closing automatically.
- K1 Open Direction: Select the opening direction.
- K2 Master Door Selector: For dual door systems.
- K3 Closed Force Selector: Adjust the closing force.
- K4 Install Mode Selector: Select the installation mode.
Refer to the labels on the control panel for specific adjustment instructions.
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your door opener.
- Cleaning: Periodically clean the main unit and tracks to prevent dust and debris buildup, which can affect smooth operation. Use a soft, dry cloth.
- Check Connections: Regularly inspect all electrical connections and mounting screws to ensure they are secure. Tighten any loose fasteners.
- Smooth Operation: Observe the door's movement. If you notice any unusual noises or resistance, inspect the moving parts for obstructions or wear.
- Lubrication: While specific lubrication points are not detailed, ensure that any moving mechanical parts operate smoothly. Consult a professional if lubrication is required for internal components.
6. Troubleshooting
6.1. Obstruction Detection

The door opener is equipped with a safety feature that detects obstructions. If an object is detected in the closing path, the door will automatically reopen to prevent accidents or injuries. Ensure the path is clear for normal operation.
6.2. General Issues
- Door Not Opening/Closing: Check power supply, remote control battery, and ensure no physical obstructions are blocking the door. Verify all connections are secure.
- Remote Control Not Working: Replace remote battery. Ensure you are within the 15m/49ft range. Re-pair the remote if necessary (refer to the RF Card Access Manual).
- Unusual Noises: Inspect the tracks and moving parts for debris or misalignment. Ensure all screws are tight.
- Door Movement Irregular: Check the parameter settings on the control panel (opening/closing speed, angles). Adjust as needed.
If problems persist, please contact customer support or a qualified technician.
7. Specifications
| Feature | Specification |
|---|---|
| Material | Aluminum Alloy, ABS |
| Color | Silver, Black |
| Voltage | 110~220V ±10% |
| Power | 50W |
| Opening Time | 3~7s/90° |
| Hold Open Time | 1~30s |
| Max. Door Frame Depth | 450mm/17.71in |
| Min. Door Width | 660mm/26in |
| Max. Door Width | 1200mm/47.24in |
| Max. Opening Angle | 120° |
| Max. Door Weight | 100KG/220lbs |
| Environment Temperature | -20~50℃/-4~122°F |
| Protection Class | IP12D |
| Remote Control Range | 15m/49ft |
| Closing Force | 30kg/66lbs |
| Noise Level | 55DB |
| Product Size | 51.5*8*9.5cm/20.27*3.15*3.74in |
8. User Tips
- Accessibility: Utilize the manual mode for easy access for individuals with mobility challenges or when pushing a cart. The low pressure and slow closing speed enhance safety and convenience.
- Safety First: Always ensure the door path is clear before operation. The obstruction detection feature is a safety net, but proactive awareness is key.
- Customization: Take advantage of the adjustable parameters on the control panel to fine-tune the door's operation to your specific needs and preferences, such as opening speed and hold-open time.
- External Connections: Consider integrating additional components like electric locks or magnetic locks for enhanced security and functionality, as the system supports extensive external connections.
9. Warranty and Support
For warranty information, technical support, or any questions regarding your CNCEST Automatic Swing Door Opener, please contact the seller or manufacturer directly. Keep your purchase receipt and product model number (DSW-100) handy when seeking assistance.