FLIPSKY 65220

Contents

Flipsky 65220 Waterproof BLDC Motor / ESC 2-in-1 Combo

Model: 65220 | Brand: FLIPSKY

1. Introduction

The Flipsky 65220 is a high-performance, waterproof brushless DC (BLDC) motor with an integrated Electronic Speed Controller (ESC), designed for various underwater and electric propulsion applications. This 2-in-1 combo offers a compact, efficient, and reliable solution for e-foils, e-surfboards, electric kayaks, and other watercraft. This manual provides essential information for the safe and effective setup, operation, and maintenance of your Flipsky 65220 motor.

Various application fields for the Flipsky 65220 motor
Figure 1: Application fields for the Flipsky 65220 motor, including e-foils, e-surfboards, paddleboards, and small watercraft.

2. Safety Precautions

  • Always disconnect the battery before performing any maintenance or installation.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Operate the motor in well-ventilated areas or submerged in water as intended to prevent overheating.
  • Keep hands and loose clothing away from the propeller when the motor is powered.
  • Use appropriate personal protective equipment (PPE) during installation and testing.
  • Do not attempt to disassemble the waterproof components unless specifically instructed, as this may compromise the IP68 rating.

3. Package Contents

Verify that all items are present in your package:

  • Flipsky 65220 BLDC Motor with Integrated ESC
  • Propeller (if included in your specific kit)
  • XT90 Male Connector (pre-attached to power cables)
  • PPM Signal Cable
  • Type C USB Communication Cable
Flipsky 65220 motor with integrated ESC and all included components
Figure 2: Overview of the Flipsky 65220 motor and its main components.

4. Specifications

4.1. 65220 Motor Specifications

ParameterValue
ModelΦ65 x 220 mm
Voltage Range6-20S
Maximum Power6000 W
Rated Power3000 W
Rated Current60 A @50V
Maximum Current100A @30V
Insulation CurrentAC 500V / 1mA / 3s
Resistance58 mΩ
Inductance170 μH
Three-phase Wire3 x 10 AWG (5.5 mm)
Power ConnectorXT90
ShaftΦ12 -0.005 / -0.01
Rated Torque6.3 N·m
Number of slots & poles18 N / 6p
Maximum Torque9 N·m
Waterproof LevelIP68
Weight3.23 kg
Dimensions of the Flipsky 65220 motor
Figure 3: Dimensions of the Flipsky 65220 motor (65mm diameter, 220mm length).
Detailed specifications and thrust table for the Flipsky 65220 motor
Figure 4: Detailed specifications and thrust table for the Flipsky 65220 motor.

4.2. Integrated ESC Specifications

  • Firmware: 5.2 VESC TOOL3.0
  • ESC Type: Flipsky 75100
  • ESC Drive Mode: Default PPM (customizable to ADC, UART)
  • Communication Port: Default USB (customizable to CAN)

4.3. Battery Box Parameters (if applicable to your kit)

  • Outer Box Size: 371 x 269 x 186 mm
  • Waterproof Grade: IP67
  • Battery Box Material: ABS
  • Voltage: 50.4V
  • Cell Specifications: Molicel P42A 27100
  • Battery Capacity: 12S 4P 16.8AH / 846.72WH / 16800mAh
  • Operating Environment: -20°C to +50°C
  • Charger: 50.4V 5.5A
  • Charging Time: Approximately 2.6 hours

5. Setup and Installation

5.1. Mounting the Motor

Securely mount the motor to your watercraft using appropriate hardware. Ensure the mounting surface is robust enough to withstand the motor's thrust and vibrations. The motor should be positioned to allow for optimal water flow around the propeller and cooling fins.

5.2. Electrical Connections

Carefully connect the motor to your battery and control system as follows:

  • Battery Connection: Connect your battery pack to the XT90 male connector on the motor's power cables. Ensure correct polarity (red to positive, black to negative).
  • ESC Signal: Connect the PPM signal cable from your receiver or control unit to the corresponding port on the motor's integrated ESC.
  • Communication Port: Use the Type C USB cable to connect the motor to a computer for configuration via VESC Tool.
Connection points for the Flipsky 65220 motor
Figure 5: Connection points for the Flipsky 65220 motor: XT90 for battery, PPM for ESC signal, Type C USB for communication.

6. Operating Instructions

6.1. Initial Power-Up and Testing

  1. After all connections are made, perform a visual inspection to ensure everything is secure.
  2. With the motor safely secured and clear of any obstructions, connect the battery.
  3. Slowly increase the throttle input from your control unit to test motor rotation and response. Observe for any unusual noises or vibrations.
  4. Ensure the motor is adequately cooled during operation. For underwater applications, ensure it is fully submerged.

6.2. Configuration with VESC Tool

The integrated ESC is based on VESC technology, allowing for extensive customization and monitoring via the VESC Tool software. Connect the motor to your computer using the Type C USB cable.

  • Download the latest VESC Tool from the official VESC project website.
  • Follow the VESC Tool's motor setup wizard to configure motor parameters, input type (PPM, ADC, UART), current limits, and other advanced settings.
  • Regularly check motor and ESC temperatures during operation, especially during initial setup and high-load conditions.
Video 1: Product showcase of the Flipsky 65220 motor, demonstrating its features and design.
Performance data of the Flipsky 65220 motor under water
Figure 6: Performance data of the Flipsky 65220 motor under water at 60V 50% duty cycle, displayed via VESC tool.

7. Maintenance

  • After Each Use: Rinse the motor with fresh water to remove salt, sand, or debris, especially after use in saltwater.
  • Inspection: Regularly inspect the propeller for damage, entanglement, or wear. Check all cables and connectors for signs of damage or corrosion.
  • Storage: Store the motor in a dry, cool place away from direct sunlight. If storing for extended periods, ensure the battery is charged to a storage voltage (typically 3.8V/cell).
  • Propeller Replacement: If the propeller is damaged, replace it with an original Flipsky spare part to maintain performance and balance.

8. Troubleshooting

ProblemPossible CauseSolution
Motor not spinningNo power, incorrect signal, ESC faultCheck battery connection, verify signal cable, check VESC Tool for errors.
Motor stutters or runs roughIncorrect motor detection, damaged propeller, loose connectionsPerform motor detection in VESC Tool, inspect/replace propeller, check all wiring.
OverheatingInsufficient cooling, excessive load, incorrect settingsEnsure proper submersion/cooling, reduce load, adjust current limits in VESC Tool.
No communication with VESC ToolDriver issue, faulty USB cable, incorrect port selectionInstall VESC drivers, try another USB cable, select correct COM port in VESC Tool.

9. User Tips

  • The motor is generally ready to use out of the box, but for optimal performance and to match your specific setup, it is highly recommended to use the VESC Tool for customization.
  • Battery life will vary significantly based on power consumption and throttle usage. Monitor your battery's state of charge during operation.
  • Familiarize yourself with the VESC Tool's features to unlock the full potential and fine-tune the motor's behavior for your application.

10. Warranty and Support

10.1. Warranty Policy

The warranty period for electronic products (ESC/Motor/Battery) is 2 months from the 7th day after shipment (the shipping date is checked by logistic record). For non-electronic products, the warranty period is 2 months since the 7th day after shipment.

The following conditions are NOT covered by the above warranty:

  • Cannot provide purchase channel source proof.
  • Mechanical damage to electronic components or PCB.
  • PCBA board has repair soldering iron traces (excluding solder the cable bullet connectors).
  • Wire damage or external impact damage.
  • For non-waterproof products, there is water inflow.
  • Abnormal applications beyond the product specifications.

10.2. Technical Support

For technical assistance or warranty claims, please contact Flipsky support at: flipsky_service@outlook.com. Please provide your original source order number and a detailed description of the issue.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.