WINXU FOC 30A-S866 Color Kit

Contents

E-bike Brushless Motor Controller and S866 LCD Color Kit User Manual

Model: FOC 30A-S866 Color Kit

Brand: WINXU

1. Product Information

Product Name: Brushless Motor Controller for E-Bike

Model: 250W / 350W / 500W / 750W (Controller supports up to 1500W motors)

Batch Number: 260215P-01

This controller is a 3-mode sine wave controller designed for brushless gearless motors and geared Hall motors. It features low noise, strong power, and stable drive, supporting up to 30A current. The controller includes self-learning wires for compatibility with almost all brushless motors.

The kit includes an S866 LCD Color Display, which uses a UART protocol.

Specifications

Attribute Value
Type Controller
Input Voltage 36V / 48V / 60V
Motor Power 1000W / 1200W / 1500W
Max. Current 30A
Motor Type Brushless motor with hall sensor
LCD Model S866
Protocol Type UART
Brake Type Low level brake
Controller Dimensions 155mm x 75mm x 45mm (approx.)
LCD Display Dimensions (S866) Approx. 110mm x 60mm
Waterproof Rating IPX6 (Controller)

The controller features an IPX6 waterproof design with a fully sealed process and screws with waterproof seals. It is constructed from aluminum alloy for heat dissipation and prolonged product life.

Controller with IPX6 waterproof design and aluminum material details

Image: Controller showcasing IPX6 waterproof design and durable aluminum casing.

Internal view of the controller PCB, highlighting lead-free process and fire-resistant wires

Image: Internal view of the controller's high-quality lead-free PCB and fire-resistant wiring.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

Warning: Keep the device and its cord out of reach of children under 3 years old.

Before installing the controller, please disconnect the battery power supply. Do not work with the power on, as it may easily damage the equipment.

Before starting the installation, please be sure to carefully read the wiring diagram and fully understand the functions of all connectors before proceeding.

Important Note:

  • This brushless controller is for brushless motors only. Not suitable for brush motors.
  • The motor needs to have a Hall sensor. If used with a Hall-less brushless motor, the LCD will always display the E07 fault code.
  • If using PAS pedal assist, please use dual Hall PAS sensors.
  • This is a true sine wave controller. It does not support cruise and 6 km/h mode. The cruise button operation on the LCD is invalid.
  • This controller does not support P08 (Speed Limit) and P14 (Current Limit) settings from the LCD. The external speed limit connector only limits speed to 6km/h-27km/h. It cannot meet a 25km/h speed limit requirement.

3. Setup Instructions

3.1 Pre-use Preparation

Before installing the controller, ensure the battery power supply is disconnected. Operating with power on can damage the equipment.

3.2 Reading the Product Wiring Diagram

Carefully review the wiring diagram below to understand the function of each connector before installation.

Detailed wiring diagram for the WINXU FOC Brushless Motor Controller, showing connections for battery, horn/light, speed limit, throttle, PAS, LCD/LED display, power lock, low level brake, self-learning, motor hall, and motor phase wires.

Image: Detailed wiring diagram for the controller.

3.3 Connector Function Introduction and Installation Steps

  1. Motor Phase Wire: Connect the 3-phase wires (thick wires) of your motor: yellow, green, and blue according to the color code. Ensure a secure connection as this handles large current.

  2. Motor Hall Sensor: Connect the motor Hall sensor. This controller uses a 6-wire Hall sensor. Red, yellow, and blue are Hall signal wires; red and black are working voltage cables; white is the motor speed signal cable. Connect according to correct colors. If your motor has a 5-wire Hall sensor, ignore the white speed signal cable; the controller will automatically obtain the motor speed signal from the Hall signal cable.

  3. LCD Display: This 5-pin connector uses a UART protocol LCD display. Red and black are for operating voltage, blue for controller power control, green is RX, and yellow is TX.

  4. Power Lock: This is a key lock connector. If your original bicycle has a key lock, connect its switch here. If not, ignore it.

  5. Throttle: This connector is for a Hall throttle (thumb or twist type). It receives a signal voltage of 1.1-4.2V. Red and black are operating voltage, white is the Hall signal. Connect correctly.

  6. PAS Sensor: This controller uses a magnetic pulse type PAS sensor. Red and black are power voltage wires, and blue is the pulse signal cable.

  7. Speed Limit: This connector is for external speed limiting. When plugged in, the controller activates speed limit mode (15-27 km/h). This controller cannot set speed limit via the LCD's P08 setting.

  8. Low-Level Brake: This power-off braking system cuts motor power when the brake is applied. Black is the negative wire, white is the brake signal cable. Connect correctly if your brake is a low-level type with 2 cables.

  9. Light Power: This connector outputs battery voltage for devices like headlights, brake lights, horns, and USB chargers. Yellow is the positive terminal, black is the negative terminal.

  10. Battery: This is the device's power supply. Connect positive and negative terminals correctly. Incorrect connection can cause short circuits, overheating, and damage. Connect the battery last and double-check all connections for short circuits and correct polarity.

  11. Automatic Detection (Self-Learning Cable): This connector is used for motor matching. After initial installation, use this connector to complete motor matching. Turn on the device, lift the motor hub, and plug in this connector. The motor will start driving. If it drives in reverse, disconnect and reconnect the connector to change direction. Once the motor drives correctly and without vibration, disconnect the self-learning cable. You can then test riding normally.

3.4 Installation Video Guide

Video: Demonstration of the controller wiring and self-learning process.

4. Operating Instructions

4.1 LCD Display Functions (S866)

Close-up of S866 LCD display showing battery level, voltage, speed, PAS level, and odometer.

Image: S866 LCD display showing various parameters like battery capacity, speed, and PAS level.

4.2 How to Enter Setup Mode

Long press the '+' and '-' buttons for 3-5 seconds after switching on the computer to enter the setting mode. The parameters will blink. Short press the 'M' button to switch parameters, and press the '+' and '-' buttons to select parameters.

4.3 Parameter Introduction

Parameter Description
P00Restore factory setting
P01Backlight Brightness
P02Mileage unit
P03Voltage selection
P04Sleep Time
P05PAS Gear
P06Wheel Diameter (in inches)
P07Speed Magnet (normally set to 23)
P08Speed Limit (Controller not supported for setting via LCD)
P09Zero Start / Non-Zero Start
P10Drive mode setting (0: PAS drive, 1: throttle drive, 2: PAS and throttle drive)
P11PAS sensitivity setting
P12PAS start strength setting
P13PAS magnet disc type setting
P14Current Limit Setting (Controller not supported for setting via LCD)
P15-19Functions not yet opened, ignore.

5. Maintenance & Storage

5.1 Cleaning

Turn off the device before cleaning. Use a soft, lint-free cloth to wipe the surfaces.

5.2 Storage

Store the device in a dry place at room temperature (15°C - 35°C).

For long-term storage, if not used for a long time, charge the device to 50% every 3 months to maintain battery health.

5.3 Disposal & Recycling

This product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

6. Troubleshooting

6.1 LCD Error Code Explanation

Code Description
E00Normal status
E01Undefined
E02Brake fault
E03PAS sensor fault
E046KM/H cruise mode (Note: This controller does not support cruise mode)
E05Real-time cruise (Note: This controller does not support cruise mode)
E06Battery undervoltage
E07Motor failure (Also displayed if using a Hall-less motor)
E08Throttle fault
E09Controller failure
E10Communication signal reception failure
E11Communication signal transmission fault
E12BMS communication fault
E13Headlight fault

6.2 Specific Troubleshooting Steps

  • E07 Motor Failure: If this error displays after initial installation, it means the controller has not completed motor matching. Use the self-learning cable as described in the Setup section. If the error persists, the driving speed might be insufficient during the self-learning process, or there might be a fault with the motor or motor Hall sensor. This error will also display constantly if a Hall-less motor is used.

  • E10 Communication Fault: If you encounter an E10 communication fault, inspect the TXD and RXD data connections on the PCB for any bridged solder connections. A user reported resolving this issue by removing a solder bridge.

    S866 LCD display showing an E10 communication error.

    Image: S866 LCD display showing an 'E 10' communication error.

    Close-up of a PCB showing a bridged solder connection between TXD and RXD data lines.

    Image: Example of a bridged solder connection on the PCB, specifically on TXD and RXD data lines, which can cause E10 errors.

7. User Tips

  • Motor Compatibility: This controller is specifically designed for brushless motors with Hall sensors. If your motor is Hall-less, the LCD will continuously display an E07 error code. Consider an S810 LED panel kit if you have a Hall-less motor.

  • PAS Sensor: For pedal assist functionality, ensure you use dual Hall PAS sensors for optimal performance.

  • Accurate Speed Display: To achieve accurate speed readings on the LCD, enter the LCD setting mode (long press '+' and '-' buttons). Set your motor wheel diameter in P06 (in inches) and the speed magnet in P07 (typically 23). Compare the LCD speed with a GPS navigation app and adjust P07 to fine-tune the display ratio until it matches.

  • Display Visibility: The LCD display may have a limited viewing angle and brightness. When changing settings or checking information, you might need to shade the display with your hands for better visibility.

  • Initial Motor Direction: If the motor rotates in reverse after initial installation, this is normal. Short-connect the self-learning wire again to change the motor's initial direction.

8. Warranty & Support

8.1 Manufacturer Information

Name: ShenZhne Winxu Technology Co,.Ltd

Address: No. 118, Building B, Yongxing Office Building, No. 68, Tianyun Road, Songgang Street, Baoan District, Shenzhen, China

E-mail: Winxutech@163.com

Tel: +86-15814065441

8.2 EU Authorized Representative

Name: Vermilion Bird OU

Address: Tartu mnt 67/1-13b, Kesklinna linnaosa, 10115 Tallinn Harju maakond, Estonia

E-mail: vermilionbird.eu@outlook.com

8.3 Additional Resources

For a comprehensive user manual in PDF format, please refer to the official document available at: WINXU E-bike Controller User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.