1. Product Overview
1.1 Product Description
The Dynoracing 60MM Car Turbo Boost Gauge is designed for car modification, repairing, and upgrading vehicle performance. It features a black face with clear numbers and a pointer, offering both red and white backlighting for easy reading in various lighting conditions. Engineered with high-quality materials, this gauge ensures durability and compliance with EU regulations. It provides high sensitivity and is easy to operate.
1.2 Package Contents
The package includes the following main components:
- 1 x Turbo Boost Gauge
- 1 x Boost Sensor
- 1 x English Manual (PDF version available online)
Note: Auxiliary installation accessories may need to be purchased separately.
2. Safety Warnings & Compliance
2.1 EU Regulatory Compliance
This product complies with EU regulations. Do not use or modify this component beyond the scope specified in this manual, as non-compliance may invalidate vehicle type approval and lead to legal liability.
2.2 Professional Installation Required
Installation must be performed by a qualified automotive technician with relevant EU automotive repair certifications (e.g., ASE, IMI). Improper installation may cause component failure, vehicle damage, or personal injury.
2.3 Safety Precautions
- Disconnect the vehicle battery before installation to avoid electrical short circuits.
- Wear protective gear (safety goggles, gloves, anti-slip shoes) during installation.
- Do not install or operate the product while the vehicle is in motion or the engine is running (except for post-installation testing as specified).
2.4 Compatibility Check
Verify that the product is compatible with your vehicle's make, model, and year before installation. Using incompatible components may result in mechanical malfunction or safety hazards.
2.5 Important Safety Information
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Please dispose of this discarded product in a reasonable manner according to local regulations, without polluting the environment and protecting the health of others.
3. Setup
3.1 Pre-Installation Preparation
- Park the vehicle on a flat, level surface and engage the parking brake. Turn off the engine and allow it to cool completely (minimum 30 minutes).
- Clean the installation area (e.g., engine bay, suspension mount) with a non-corrosive cleaner to remove dirt, oil, or debris. Dry thoroughly with a clean cloth.
3.2 Step-by-Step Installation
- Locate the original component to be replaced.
- Refer to the electrical wiring diagram below for proper connections.
- Find professional repair personnel for installation. If you install it yourself, please ensure you have rich experience and hands-on ability in this area.
This diagram illustrates the connections for the Boost/Vacuum Gauge. The main wire harness includes connections for the power cord (same for all gauges), signal lines, and specific connections for the Boost Sensor. The gauge requires a +12V connection to the battery, a connection to the lighting switch (+), an ignition switch (+), and a battery ground (-). The Boost Sensor connects via RED, GREEN, WHITE, and BLACK wires as shown.
3.3 Post-Installation Testing
- Test whether the installed product can be used normally (e.g., ensure it does not trigger a car malfunction alarm and does not affect driving).
- If any issues are detected, stop using the vehicle immediately and contact the manufacturer or a qualified technician for inspection.
- Complete all steps and clean the vehicle.
4. Operating Instructions
The Dynoracing Turbo Boost Gauge is designed for straightforward operation once installed. The gauge features a clear dial with numbers and a pointer for easy reading of boost pressure in Kpa.
4.1 Backlighting
The gauge offers switchable red and white backlighting. This feature allows you to select the preferred illumination color for optimal visibility in various lighting conditions, especially in darkness. The backlighting can typically be switched via a dedicated button or wiring configuration (refer to the wiring diagram for specific connections related to lighting).
5. Maintenance & Care
5.1 Regular Inspection
Inspect the component every 5,000 km or 6 months (whichever comes first). Check for loose bolts, cracks, corrosion, or wear. Tighten loose hardware and replace damaged parts promptly.
5.2 Cleaning
Clean the component with a soft brush. Avoid using abrasive cleaners, solvents, or high-pressure water (which may damage the surface or seals).
5.3 Replacement Interval
Replace the component if it shows signs of permanent damage.
5.4 Storage
If removing the component for long-term storage, clean it thoroughly, dry completely, and store in a cool, dry place away from direct sunlight and corrosive substances.
6. Troubleshooting
If you encounter any issues with your Dynoracing Turbo Boost Gauge, please consider the following general troubleshooting steps:
- No Power/No Illumination: Check all electrical connections, especially the +12V battery, ignition, and ground wires, as well as the lighting switch connection. Ensure fuses are intact.
- Incorrect Readings: Verify the boost sensor is correctly installed and connected. Check for any leaks in the vacuum/boost lines.
- Intermittent Operation: Inspect wiring for loose connections or damage. Ensure the vehicle's electrical system is stable.
For persistent issues, professional diagnosis and repair are recommended.
7. Specifications
| Attribute | Value |
|---|---|
| Brand Name | Dynoracing |
| Model Number (SKU) | BX101467 |
| Item Weight | 0.45 KG |
| Item Height | 60mm |
| Item Width | 60mm |
| Item Length | 60mm |
| Manufacturer Part Number | Turbo Boost gauge |
| Interchange Part Number | Turbo Boost meter |
| Origin | Mainland China |
| Material | ABS |
| Car Maker Compatibility | All 12Volt Cars |
| Power | DC 12V Professional |
| Light Color | Red & White Lighting |
| Unit | Bar (100KPA) |
| Diameter | 2.5" / 60mm |
| Measurement Range | 0~2 (100kpa) |
8. User Tips
While no specific user reviews or Q&A were provided, here are some general tips for using and maintaining your Dynoracing Turbo Boost Gauge:
- Optimal Placement: Choose a mounting location that allows for clear visibility while driving without obstructing your view of the road or other essential instruments.
- Wiring Management: Ensure all wiring is neatly routed and secured to prevent chafing, short circuits, or interference with vehicle controls.
- Regular Checks: Periodically check the boost sensor and its connections for any signs of wear or damage, especially if you notice inconsistent readings.
- Lighting Preference: Experiment with both white and red backlighting to determine which color provides the best visibility and least distraction for your driving environment.
9. Warranty & Support
9.1 Warranty Coverage
The manufacturer provides a 1-year limited warranty from the date of purchase, covering defects in materials and workmanship under normal use and proper installation. This warranty applies only to the original purchaser and is non-transferable.
9.2 Warranty Exclusions
This warranty does not cover:
- Damage caused by improper installation, misuse, abuse, or modification of the product.
- Wear and tear due to normal use (e.g., surface scratches, minor corrosion).
- Damage from accidents, natural disasters, or exposure to extreme temperatures/chemicals.
- Failure to follow maintenance instructions outlined in this manual.
9.3 Manufacturer Contact Information
Company Name: Ruian Biaoxin Electronic Commerce Inc.
Address: No. 190, Youdian South Road, Tingtian Street, Ruian city, Wenzhou, Zhejiang, China, 325200
Contact: jimix-racing@hotmail.com / 86-13967716933
9.4 EU Authorized Representative
Company Name: ORIENT CONSULTING SL
Address: Av.de la Industria, 2, Nave 16, 28947 Fuenlabrada Madrid, Spain
Contact: rae@orientconsulting.es / 34-912918327
9.5 Additional Resources
A PDF version of the user manual is available for download: User Manual (PDF)