1. Introduction
The CooSpo BK9C Bicycle Cadence Sensor is a compact and lightweight device designed to accurately measure your cycling cadence in real-time. Utilizing advanced dual-meter hybrid algorithm technology, it provides precise data without the need for magnets. It supports both Bluetooth 5.0 and ANT+ connectivity, making it compatible with a wide range of cycling computers, smartwatches, and fitness applications.

Product overview highlighting key features.
2. Features
- Dual-Mode Connectivity: Supports both Bluetooth 5.0 and ANT+ for broad compatibility.
- Magnet-Free Design: Utilizes an advanced dual-meter hybrid algorithm (accelerometer and magnetometer) for accurate cadence measurement without external magnets.
- Real-time Cadence Measurement: Provides instant feedback on your pedaling rate to help improve performance.
- LED Indicator: A blue LED light indicates device status.
- IP67 Waterproof: Designed to withstand various weather conditions (no soaking or high-pressure cleaning).
- Long Battery Life: Up to 300 hours of operation on a single CR2032 coin cell battery.
- Lightweight and Compact: Weighs only 8.4g and has a slim profile for easy installation.

Advanced dual meter hybrid algorithm for magnet-free operation.
3. Specifications
| Feature | Specification |
|---|---|
| Model | BK9C |
| Connectivity | Bluetooth 5.0, ANT+ |
| Measurement Type | Cadence |
| Sensor Type | Accelerometer, Magnetometer (Magnet-free) |
| Battery Type | CR2032 Coin Cell |
| Battery Life | Approx. 300 hours |
| Waterproof Rating | IP67 |
| Weight | 8.4g |
| Dimensions (L x W x T) | 1.3 inch x 1.2 inch x 0.3 inch |
| Material | Plastic |

Physical dimensions and weight of the sensor.
4. Setup
4.1 Battery Installation
- Gently twist the battery cover on the back of the sensor counter-clockwise to open it.
- Insert a new CR2032 coin cell battery with the positive (+) side facing upwards.
- Align the battery cover and twist clockwise to securely close it.

Battery installation and replacement.
4.2 Sensor Installation
The BK9C sensor is designed for easy installation on your bicycle's crank arm.
- Attach the provided rubber pad to the back of the sensor.
- Position the sensor on the inside of your bicycle's non-drive side crank arm.
- Use the included rubber band to securely fasten the sensor to the crank arm. Ensure it is tight enough to prevent movement during your ride.

Installation steps for mounting the sensor on the crank arm.
4.3 Pairing with Devices
The BK9C sensor supports both ANT+ and Bluetooth connections. To pair:
- Ensure the sensor is awake. Rotate your bike's crank arm a few times to activate the sensor. The blue LED will flash.
- On your cycling computer, smartwatch, or fitness app, navigate to the 'Add Sensor' or 'Pair Device' menu.
- Select the CooSpo BK9C (or similar name) from the list of available sensors.
- Once connected, the device will display your cadence data.

Compatibility with various cycling devices and apps.
5. Operating Instructions
5.1 Activating the Sensor
The sensor automatically activates when it detects movement. Simply rotate your bicycle's crank arm a few times to wake it up. The blue LED indicator will flash to confirm activation.
5.2 LED Indicator
- Blue LED flashes: Sensor is active and transmitting data.
- No LED: Sensor is in sleep mode or battery is depleted.

CooSpo BK9C sensor with its blue LED indicator.
6. Maintenance
6.1 Battery Replacement
When the sensor stops transmitting data or the LED no longer flashes upon activation, it's likely time to replace the battery. Follow the steps in Section 4.1 for battery installation.
6.2 Cleaning
The BK9C sensor is IP67 waterproof, meaning it is protected against temporary immersion in water. To clean, wipe the sensor with a damp cloth. Do not soak the sensor in water or use high-pressure cleaning methods, as this may damage the device.
7. Troubleshooting
- Sensor not detected by device:
- Ensure the sensor is awake by rotating the crank arm.
- Check if the battery is correctly installed and has sufficient charge. Replace if necessary.
- Make sure Bluetooth/ANT+ is enabled on your receiving device.
- Move the sensor closer to your receiving device during pairing.
- Try restarting both the sensor (by removing and reinserting the battery) and your receiving device.
- Inaccurate cadence readings:
- Ensure the sensor is securely mounted on the crank arm and not moving.
- Verify that the sensor is correctly identified as a cadence sensor on your receiving device.
- LED not flashing:
- The sensor might be in sleep mode. Rotate the crank arm to wake it up.
- Check the battery level and replace if needed.
8. User Tips
Based on common user experiences, here are some tips for optimal use:
- Crank Arm Placement: For best results, ensure the sensor is mounted on the inside of the non-drive side crank arm, away from any obstructions that might interfere with its movement or signal.
- Battery Life: While rated for 300 hours, actual battery life can vary based on usage and environmental conditions. It's a good practice to carry a spare CR2032 battery for longer rides or tours.
- Firmware Updates: Periodically check the CooSpo official website or app (if available) for any firmware updates for your sensor, which can improve performance and compatibility.
9. Warranty and Support
The CooSpo BK9C Cadence Sensor comes with a standard manufacturer's warranty. Please refer to the warranty information provided at the time of purchase or contact CooSpo customer support for details regarding warranty coverage and service.
For technical assistance, troubleshooting, or product inquiries, please visit the official CooSpo website or contact their customer service department.