DykbRadio PLJ-096OLED-L1

Contents

PLJ-096OLED-L1 OLED Frequency Display Module

High-Precision Frequency Counter for Ham Radio Transceivers and RF Applications

1. Product Overview

The PLJ-096OLED-H1 is a high-precision frequency counter module featuring a 2.7GHz RF front-end with IPEX input, a precision timing engine with advanced gating algorithm, and dual independent IF offset capabilities. It is powered by a ±2.5ppm TCXO reference for exceptional stability. The module is ideal for microwave signal generator readout, ham radio transceiver frequency display, RF amplifier tuning systems, and satellite communication test benches.

Key Features

  • Frequency Range: 1kHz to 100MHz (H1 model: 20MHz-2.7GHz)
  • Resolution: 100Hz (0.64s gate) / 64Hz (1.0s gate) for H1 model; 1Hz (1.0s gate) for L1 model.
  • TCXO Stability: ±2.5ppm (KDS/EPSON)
  • Dual IF Offset: Independent ±99.9999MHz (100Hz steps)
  • OLED Display: High-contrast, clear readout on a 0.96-inch screen.
  • UART Output: TTL serial (115200bps) for data logging.
  • EEPROM Memory: Settings retention.
  • Compact Size: 27.3 x 27.8 × 19 mm
PLJ-096OLED-L1 Frequency Meter with OLED display showing 100.000000 MHz and key features listed.
Figure 1: PLJ-096OLED-L1 module displaying 100.000000 MHz. Key features include 0.96-inch OLED display, ±2.5ppm TCXO frequency reference, 0.1/1.0 second gate time, 10/1 Hz measurement accuracy, 1kHz to 100MHz measurement range, dual mid-frequency and dual modes, and serial port output of measurement data.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

Critical Power Requirement

CRITICAL: Power requirement - Must use ≥8V supply (5V damages IC). This module requires a power supply of 8-10V DC (9V recommended). Do NOT use 5V - it will damage the internal IC and permanently destroy the module. Always verify your power supply voltage before connecting.

RF Input Sensitivity

DANGER: RF INPUT SENSITIVITY - Do not exceed -15dBm. The RF input sensitivity is -15dBm. Excessive input power may damage the prescaler and front-end circuitry. Use external attenuation when measuring high-power signals.

ESD Precautions

CAUTION: ESD sensitive - Handle with care. The module contains ESD-sensitive components. Use proper ESD precautions during handling and installation.

Electrical Safety

  • Power supply: 8-10V DC (9V recommended), 60mA.
  • RF input: IPEX Gen1 connector.
  • Input impedance: High-Z (>1MΩ).
  • Minimum frequency for accurate measurement: > 20MHz.
  • Do not exceed the maximum RF input power.
  • Keep the module away from water, moisture, and conductive debris.
  • Do not disassemble or modify the internal circuitry - there are no user-serviceable parts.

Handling Precautions

  • Use proper ESD-safe workstations and grounding when handling the module.
  • Handle the PCB by the edges to avoid damaging components.
  • Do not bend or stress the IPEX connector.
  • Do not drop or mechanically shock the module - the TCXO and OLED are delicate.

3. Setup & Connection

Connection Steps

  1. Power Connection: Connect a 9V DC power supply (8-10V) to the XH2.54-2P power connector. Do NOT use 5V.
  2. RF Input: Connect your signal source to the IPEX connector using the included IPEX-to-SMA-F cable (15cm).
  3. UART (Optional): Connect the TTL serial output (GND / TX / RX) to a microcontroller or PC for data logging.
  4. Power On: Apply power - the OLED display will show the frequency readout.
  5. Configure IF Offset (if needed): Use the onboard controls to set IF1/IF2 offsets for add/subtract modes.
Back of the PLJ-096OLED-L1 PCB showing power interface, signal input, serial port output, VC-TCXO, frequency fine-tuning, and adjustment keys.
Figure 2: Back of the PCB (3D view) with labeled components. Key labels include Power interface, Signal input, Serial port output (UART), VC-TCXO, Frequency fine-tuning, Adjustment key (K2, K1), and a note to short-circuit J1 for power supply issues if the electronic switch fails.
Top view of the PLJ-096OLED-L1 PCB, showing the layout of components and connectors.
Figure 3: Top view of the PCB, illustrating the component arrangement.

4. Operation

General Usage

Once powered on, the OLED display will show the measured frequency. The module automatically measures and displays the frequency of the input signal.

Gate Time Selection

The module offers selectable gate times of 0.64s or 1.0s. This choice affects the resolution and update rate:

  • 0.64s gate: Faster refresh, lower resolution (100Hz).
  • 1.0s gate: Higher resolution (64Hz), slower refresh.

Choose the gate time based on your application's requirements for speed versus precision.

IF Offset Configuration

The module supports dual independent IF offsets (IF1/IF2) with ±99.9999MHz range in 100Hz steps. These can be configured for add/subtract modes using the onboard controls. Refer to the detailed PDF user manual for specific instructions on adjusting IF offsets.

Video Demonstration

Video 1: Demonstration of the frequency meter measuring various frequencies from a signal generator, showing the OLED display updating with readings from 0.01MHz to 100MHz.

5. Technical Specifications

ParameterValue
Product TypeOLED Frequency Counter Module
ModelPLJ-096OLED-H1
Frequency Range20 MHz – 2.7 GHz (H1 model) / 1kHz to 100MHz (L1 model)
Resolution100Hz (0.64s gate) / 64Hz (1.0s gate)
Gate Time0.64s or 1.0s selectable
Reference Stability±2.5ppm (KDS/EPSON VC-TCXO)
Input ImpedanceHigh-Z (>1MΩ)
RF Input Sensitivity-15dBm (typ)
Power Supply8-10V DC (9V recommended)
Current Draw60mA @ 9V
UART OutputTTL serial (GND/TX/RX), 115200bps default
IF OffsetDual independent ±99.9999MHz (100Hz steps)
MemoryEEPROM settings retention
Dimensions27.3 × 27.8 × 19 mm
Operating Temperature-20°C to +70°C
CertificationsCE, RoHS, WEEE Compliant

Performance Comparison (H1 vs L1)

ModelRangeResolutionPower
H1 (This)20M-2.7G64Hz (1s gate)9V / 60mA
L11k-100M1Hz (1s gate)5V / 30mA

Test Data

Table showing test data of Agilent 8648C, including test frequency points and sensitivity in mV RMS.
Figure 4: Test data of Agilent 8648C. The table shows test frequency points from 50 Hz to 30 MHz and corresponding sensitivity in mV RMS. Note: The positions of the sensitivity adjustment potentiometers are different. The data in this table is for reference only.

6. Applications

  • Microwave signal generator readout
  • Ham radio transceiver frequency display
  • RF amplifier tuning systems
  • Satellite communication test benches
  • RF test equipment frequency readout
  • Oscillator calibration systems
  • Educational lab instruments

7. Maintenance & Storage

Cleaning

Disconnect power before cleaning. Use a soft, dry cloth to wipe the module. Do not use water, solvents, or abrasive cleaners.

Storage

Store in an anti-static bag in a dry environment at room temperature (15°C - 35°C). Avoid direct sunlight, high humidity, and corrosive atmospheres.

Handling

Handle by the edges of the PCB. Protect the IPEX connector and OLED display from damage.

Long-term Storage

If not used for an extended period, store in a sealed bag with desiccant. Before re-use, inspect the connectors for corrosion or damage.

8. Troubleshooting

Common Issues

  • Display shows 'ooooooo MHz' or incorrect readings: Ensure the signal frequency is above the minimum accurate measurement frequency (> 20MHz for H1 model). Check RF input connection and signal strength. Verify power supply voltage is within 8-10V DC (9V recommended) and not 5V.
  • No display or module not powering on: Check power connections. Ensure the power supply is providing the correct voltage. If the electronic switch fails, short-circuit J1 as indicated in Figure 2.
  • Difficulty connecting to an old model CB: Ensure the CB's output signal characteristics (frequency, power, impedance) are compatible with the module's specifications. You may need appropriate adapters or attenuators for the IPEX Gen1 input.

9. User Tips

  • This frequency counter can be very useful for precise tuning of amateur shortwave receivers.
  • Consider the L1 model for lower frequency ranges (1kHz-100MHz) if your application does not require the higher 2.7GHz range of the H1 model.
  • For optimal performance and longevity, always adhere to the specified power supply voltage and RF input sensitivity limits.

10. Package Contents

  • PLJ-096OLED-H1 Module ×1
  • IPEX-to-SMA-F Cable (15cm) ×1
  • XH2.54-2P Power Cable (15cm) ×1

11. Compliance Information

This product complies with the essential requirements of applicable European Directives, including but not limited to:

  • CE Marking: The product bears the CE mark in accordance with applicable EU harmonization legislation.
  • RoHS Directive (2011/65/EU): This product is compliant with the Restriction of Hazardous Substances Directive.
  • EMC Directive (2014/30/EU): This product meets electromagnetic compatibility requirements when installed properly.

CE Mark

CE

12. Disposal & Recycling

Crossed-out wheeled bin symbol
Crossed-out wheeled bin symbol

This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

For proper disposal, please:

  • Do not dispose of this product with general household waste.
  • Take the product to a designated collection facility for electrical and electronic equipment.
  • Follow local regulations for electronic waste disposal.

For more detailed information, please refer to the official user manual PDF: View User Manual (PDF)

13. Warranty & Support

For warranty information, technical support, or any inquiries regarding your PLJ-096OLED-L1 module, please contact the manufacturer:

  • Manufacturer: Shenzhen yakaiyao Trading Co., Ltd.
  • Manufacturer Address: 202, building s, No.1, 1st Road, Xiawei Industrial Zone Zhangkengjing community Guanhu Street Longhua District, Shenzhen
  • Manufacturer Email/Tel: 1241273859@qq.com

For EU customers, you may also contact the EU Authorized Representative:

  • EU Authorized Representative: MJCM SARL
  • AR Address: 78 avenue des Champs Elysees Bureau 326 France
  • AR Email: mjcm190928@gmail.com

© 2026 Product Manual. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.