SmallRig 3667C, 3668C, 3669

Contents

SmallRig Camera Cage System User Manual

Models: 3667C, 3668C, 3669

For Sony Alpha A7V, A7RV, A7RIV, A7IV, A7SIII, A1 Cameras

1. Introduction

Thank you for choosing the SmallRig Camera Cage System. This manual provides detailed instructions for the installation, operation, and maintenance of your SmallRig camera cage, designed to enhance the functionality and protection of your Sony Alpha series camera. The cage offers multiple mounting points for accessories, ensuring a versatile and secure setup for professional videography and photography.

2. Package Contents

Please verify that all components are present in your package. Contents may vary slightly depending on the specific model (3667C, 3668C, or 3669) purchased.

Standard Package (Model 3667C - Only Cage)

  • Camera Cage x 1

Advanced Kit Package (Model 3669C)

This kit includes additional accessories for enhanced functionality:

  • Camera Cage x 1
  • HDMI Cable Clamp x 1
  • Locating Handle for ARRI x 1
  • Side Handle x 1
  • Locking Side Plate x 2
Advanced Kit for Sony Alpha 7 IV / Alpha 7S III (ID: 3669C) showing included components: Cage, HDMI Cable Clamp, Locating Handle for ARRI, Side Handle, Locking Side Plate.
Figure 2.1: Advanced Kit (Model 3669C) components.

3. Specifications

FeatureDetail
MaterialAluminum Alloy, Stainless Steel, Silicone
CompatibilitySony A7R V, A7 IV, A7S III, A1, A7R IV
Product Dimensions146 x 107.6 x 64.5mm
Product Weight180g ±5g
Package Dimensions165 x 155 x 85mm
Package Weight286g ±5g
Image showing package contents and detailed specifications table.
Figure 3.1: Product Specifications and Package Contents.

4. Setup Instructions

Follow these steps to properly install your camera into the SmallRig cage and attach accessories.

4.1 Camera Installation (Three-Point Locking)

  1. Place your Sony Alpha camera into the cage.
  2. Secure the camera to the cage using the bottom 1/4"-20 screw.
  3. Locate the anti-deflection pin near the battery compartment. This pin is initially stored in a temporary hole.
  4. Remove the anti-deflection pin from its temporary storage hole.
  5. Align the anti-deflection pin with the corresponding hole on your camera and fix it into position to prevent twisting.
  6. For cameras like the Alpha 7 IV and Alpha 7 R V, use the designated locking slider side. For Alpha 7S III, Alpha 1, and Alpha 7R IV, use the other locking slider side.
  7. Important Note: To use the locking slider, you may need to remove the shoulder strap hook on the left side of your camera first.
Diagram illustrating the three-point locking mechanism with M2.5 screw, 1/4-20 screw, and anti-deflection pin storage hole.
Figure 4.1: Three-Point Locking Mechanism for secure camera mounting.
Diagram showing wide compatibility with modular design, illustrating different locking slider configurations for various Sony Alpha cameras.
Figure 4.2: Modular design for wide camera compatibility.

4.2 Attaching Accessories (Multiple Mounting Points)

The SmallRig camera cage features numerous mounting points for various accessories:

  • 1/4"-20 Threaded Holes: Standard mounting points for a wide range of accessories.
  • 3/8"-16 Locating Holes for ARRI: Designed for ARRI-standard accessories to prevent twisting.
  • Cold Shoe Mounts: For attaching microphones, LED video lights, or other cold shoe compatible devices.
  • NATO Rail: Provides quick release and attachment for NATO rail compatible accessories.
  • Strap Slots: For attaching camera straps.
  • QD Sockets: For quick-detach sling swivels.
Diagram illustrating various mounting points on the camera cage including cold shoe, ARRI locating holes, 1/4-20 threaded holes, strap slot, QD socket, NATO rail, and Arca Swiss quick release plate.
Figure 4.3: Multiple Mounting Points on the camera cage.

4.3 HDMI Cable Clamp Installation

If your kit includes an HDMI cable clamp, attach it to the side of the cage to secure your HDMI cable and prevent accidental disconnections or damage.

  • Note: The HDMI cable clamp may interfere with the sync terminal connector when used on the Sony Alpha 7R V camera. Please check clearance before use.
Image showing the HDMI cable clamp installation with anti-twist pins and 1/4-20 screw.
Figure 4.4: HDMI Cable Clamp installation.

4.4 Ergonomic Handgrip (Model 3668C, 3669C)

If your model includes a handgrip, attach it to the cage using the designated mounting points. The handgrip provides a comfortable and secure grip for handheld shooting.

Diagram illustrating the ergonomic handgrip design with 1/4-20 threaded holes, 3/8-16 locating hole for ARRI, and cold shoe.
Figure 4.5: Ergonomic Handgrip Design.

5. Operating Instructions

Once your camera is securely mounted in the cage and accessories are attached, the cage provides full access to all camera controls, buttons, and dials. The design also includes reserved space for wired battery cables and a hinge arm for quick battery swaps without removing the camera from the cage.

Image showing precise holes and accurate calibration for full access to camera controls and buttons on Sony Alpha A7R V / A7 IV / A7R IV / A7S III / A1, with reserved space for wired battery cable and a hinge arm for quick battery swaps.
Figure 5.1: Full access to camera controls and battery compartment.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the cage. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Avoid harsh chemicals or abrasive materials.
  • Screw Check: Periodically check all screws and mounting points to ensure they are tight and secure. Loose screws can lead to instability or damage to your camera.
  • Storage: Store the cage in a dry, dust-free environment when not in use.

7. Troubleshooting

7.1 Camera Not Fitting Securely

  • Ensure you have the correct cage model for your specific Sony Alpha camera. Refer to the compatibility list in Section 3.
  • Verify that the anti-deflection pin is correctly engaged after tightening the bottom screw.
  • Check for any obstructions or debris preventing a flush fit.

7.2 Accessories Not Mounting Properly

  • Confirm that the accessory's mounting interface (e.g., 1/4"-20 screw, ARRI pin, cold shoe) matches the cage's mounting point.
  • Ensure screws are tightened sufficiently but do not overtighten.

7.3 HDMI Cable Clamp Interference

  • As noted in Section 4.3, the HDMI cable clamp may interfere with the sync terminal connector on the Alpha 7R V camera. If this occurs, consider alternative cable management solutions or adjust the clamp's position if possible.

8. User Tips

  • Battery Access: The cage is designed with a hinge arm to allow quick battery swaps without removing the camera. Utilize this feature for efficient workflow.
  • Cable Management: Take advantage of the reserved space for wired battery cables and the HDMI cable clamp (if included) to keep your setup tidy and prevent accidental disconnections.
  • Compatibility Check: While the cage is compatible with many Sony Alpha models, always double-check the specific model number of your camera against the product specifications. For example, this cage is designed for A7S III, not A7S II.
  • Modular Design: Explore the various mounting points to customize your rig with handles, monitors, microphones, and lights to suit your shooting needs.

9. Warranty and Support

SmallRig products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please refer to the official SmallRig website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.