1. Product Information
This manual provides detailed instructions for the assembly, operation, and maintenance of your Ubricks UB001 Liebherr LTM11200 Crane Model. Please read all instructions carefully before use to ensure safe and correct operation.
Product Overview
The Ubricks UB001 is a giant flagship simulated crane model, consisting of 10400 pieces. It features remote control capabilities, a height of 2.8 meters, and over 20 functions, offering a realistic and engaging building and play experience.
Key Features
- DIY manual assembly for a realistic car model structure.
- Flexible rotation of wheels.
- Compatible with mainstream building block brands.
- Designed to enhance hands-on ability, logical thinking, and spatial imagination.
- Features an independent crane boom, integrated drive system, and thickened structure.
- Optional dual-mode boom (4-section for stronger lifting capacity, 5-section for higher lifting height).
- Multi-angle 4 steering modes.
- Carbon fiber architecture for enhanced durability.
2. Safety & Warnings
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- This product contains small building block parts, wheel accessories, and tiny connectors.
- Children shall use this product under the continuous supervision of adults.
- Not suitable for children under 6 years old.
- Keep unused small parts away from infants and young children.
- Do not put any parts of the product into the mouth, nose, or ears to avoid suffocation, choking, or ingestion accidents.
- Abnormal use such as violent disassembly and random splicing may cause sharp edges and structural failure, bringing safety risks.
- Please store the product in a dry, cool, and ventilated environment, avoid high temperature, humidity, and direct sunlight, and keep away from fire sources and corrosive substances.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Do not charge the battery unattended.
- Do not charge the battery near heat sources or flammable materials.
- Do not disassemble, crush, puncture, short-circuit, or expose the battery to fire.
- Stop using the battery immediately if it becomes swollen, overheated, leaks, or is damaged.
Do not dispose with domestic waste; please recycle separately.
WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
3. Specifications
| Attribute | Detail |
|---|---|
| Product Name | Toys Building Blocks Set - Engineering Vehicle |
| Brand | Ubricks |
| Model Number | UB001 |
| Batch/Serial Number | 2026/07/10 |
| Quantity | 10400 PCS |
| Material | High-quality ABS plastic (non-toxic, odorless, durable, smooth edge treatment) |
| Recommended Age | 14+ Years Old |
| Is Electric | Lithium battery |
| Block Size | Small building block (Compatible with Lego) |
| Plastic Block Shape | Self-Locking Bricks |
| Plastic Type | ABS |
| Gender | Unisex |
| Color | Red and Black |
| Height (assembled) | 2.8 m (9.19ft) |
| Product Size (Unexpanded) | 120.8 * 38.7 * 29.0 cm |
| Product Size (Expanded) | 124.0 * 75.0 * 280.0 cm |
| Package Size | 55.0 * 33.0 * 33.0 cm |
| Package Weight | 15.0 kg |
| Functions | 20+ functions (Chassis, Workbench, Crane Boom operations) |
Note: Due to changes in the angle of the boom, the expanded data may change. There may be deviation in manual measurement. Please refer to the actual situation.
4. Package Contents
Upon opening the package, ensure all components are present and undamaged. The package should contain:
- Building blocks (10400 PCS)
- Electronic components (motors, lithium batteries, remote control sets)
- Remote controller (4 sets)
- USB charging cable
- Instruction manual (this document)
- 5* M Motors
- 6* L Motors
- 5* XL Motors
- 4* Lithium Batteries
- New accessories: Base Plate for Support Leg
5. Setup Instructions
5.1 Correct Operation Steps
- Unpacking: Carefully unpack the product. Check all building blocks, electronics, remote controller, battery (if equipped), USB cable, and manual. Do not use if any parts are missing or damaged.
- Assembly: Assemble following the illustrated instructions provided in the separate assembly guide. Align blocks and press evenly. Do not apply excessive force to prevent part damage.
- Battery Installation: Fit batteries into the model and remote controller (if applicable) with correct +/- polarity. Close the battery compartment securely.
- Charging: Fully charge the rechargeable battery before first use with the supplied USB cable and certified 5V adapter. Unplug after charging.
- Power On: Press and hold the model's power button for about 2 seconds until the indicator lights up.
- Remote Pairing: Turn on the remote after powering up the model. Wait several seconds for automatic pairing. A steady indicator light means pairing succeeds.
6. Operating Instructions
6.1 General Operation
Run the model on flat, dry open ground. Keep hands, hair, and loose clothes clear of moving parts. Avoid collisions, water, sand, and steep slopes.
6.2 Functions Overview
The Ubricks UB001 crane model offers a wide range of simulated operations:
- Chassis:
- Crane walk and steering (4 modes: all-wheel steering, crab steering, reduced swing out/rear axle steering).
- Support Legs: Expansion/folding, Extension/retraction.
- Workbench:
- Upper Structure: 360° Rotation.
- Cab: Rotation, Rise/fall, Tilt up/down.
- Counterweights: Disassembly/installation, Lifting/lowering.
- Crane Boom:
- Boom: Extension/retraction, Lifting/lowering.
- Support Legs: Expansion/folding, Extension/retraction.
- Y-suspension: Expansion/folding, Lifting/lowering.
- Y-suspension: Retract/release Line.
- Hook: Lifting/lowering.
Note: Functions marked with an asterisk (*) in the assembly guide require manual operation, while the rest are electric.
6.3 Video Demonstration
Watch the official operation video for a visual guide on setting up and operating your crane model:
Video 1: Ubricks UB001 Crane Model Operation and Lifting Demonstration.
7. Maintenance & Storage Instructions
- Daily cleaning: Wipe the surface of building blocks with a clean soft cloth, or rinse briefly with clean water if needed. Do not soak the plastic parts in water for a long time to prevent plastic aging and deformation.
- Storage method: After use, collect all parts and place them in the original package or clean storage box, avoid loss of small parts.
- Maintenance notes: Do not expose the product to high temperature, low temperature, humid environment, or direct sunlight for a long time, so as to prevent plastic aging, fading, and brittleness.
- Damaged parts: If parts are damaged or missing during use, stop using them in time to avoid sharp edges scratching hands.
7.1 After Use
Power off the model and remote after use. Remove batteries for long-term storage. Keep the item in a cool, dry place away from sunlight and dampness.
8. Troubleshooting
- Missing or Damaged Parts: If you find any parts missing or damaged during unpacking or assembly, do not proceed with use. Refer to the 'Warranty & Support' section for assistance.
- Assembly Difficulties: Ensure you are following the illustrated instructions carefully. Do not force parts together. If a part does not fit, re-check the steps and part orientation.
- Model Not Powering On: Check battery installation for correct polarity (+/-). Ensure batteries are fully charged. Verify the power button is pressed and held for approximately 2 seconds.
- Remote Not Pairing: Ensure both the model and remote are powered on. Allow several seconds for automatic pairing. A steady indicator light on the remote signifies successful pairing.
- Movement Issues: Ensure the model is on a flat, dry, open surface. Check for any obstructions or misaligned parts. Verify all motors are correctly connected and functioning.
- Battery Issues: If batteries become swollen, overheated, leak, or are damaged, stop use immediately and replace them. Do not attempt to charge damaged batteries.
9. User Tips
- Assembly Process: Take your time during assembly. The assembly process is generally smooth, but careful attention to the instructions will prevent errors.
- Part Organization: The parts are well-packaged in small sealed bags. Keeping them organized during assembly can help prevent loss and speed up the building process.
- Customer Support: If you encounter any questions or issues during assembly or operation, customer support is generally responsive and helpful. Have your parts list ready if reporting missing/defective parts.
- Packaging: The product typically comes in a sturdy box, which is useful for storage of unbuilt or disassembled parts.
10. Warranty & Support
10.1 After-sales Service & Warranty
- We provide 12-month global after-sales warranty service for non-human damage products.
- If the product has quality problems, missing parts, or damage during transportation, please contact our customer service team with the order number and product photos for replacement.
- Free spare parts service is provided for conventional small parts loss within the warranty period.
10.2 Manufacturer & EU Representative Information
Manufacturer:
- Company: Shenzhen Keji Toys Co., Ltd
- Address: Daofeng Building, Dongkeng Community, Guangming District, Shenzhen City, China
- Email: KOGIService@outlook.com
EU Authorized Representative:
- Company: E-CrossStu GmbH
- Address: Mainzer Landstr.69, 60329, Frankfurt am Main
- Mail: E-CrossStu@web.de
- Tel:+4969332967674
Importer:
- Company: Shenzhen Keji Toys Co., Ltd
- Address: Daofeng Building, Dongkeng Community, Guangming District, Shenzhen City, China
11. Compliance Information
This toy product has passed authoritative professional testing and fully complies with EU, UK, and international toy safety regulations and harmonized standards. It has obtained valid market access compliance certifications and marks to meet overseas sales qualification requirements.
11.1 Valid Compliance Markings:
CE (Conforms to European Union health, safety and environmental protection requirements)
UKCA (Conforms to UK market entry safety standards)
FC (Conforms to United States electromagnetic compatibility regulatory requirements)
11.2 Applicable Official Regulations & Harmonized Standards:
- EU Toy Safety Directive: 2009/48/EC (Official Toy Safety Directive of the European Union)
- Toy Mechanical & Physical Safety Standard: EN 71-1:2014+A1:2018
- Toy Flammability Safety Standard: EN 71-2:2020
- Toy Toxic Element Migration Limit Standard: EN 71-3:2019+A1:2021
- Hazardous Substance Restriction Directive: 2011/65/EU (RoHS Directive)