PEAKMETER PM8200A/B

Contents

PEAKMETER PM8200A/B Voltage and Continuity Tester Instruction Manual

Model: PM8200A/B | Brand: PEAKMETER

1. Introduction

The PEAKMETER PM8200A/B is a professional-grade, multifunctional voltage and continuity tester designed for electrical maintenance and inspection. It features a robust IP65 waterproof and dustproof rating, ensuring reliable performance in various environments. This instrument is capable of measuring AC/DC voltage, performing continuity tests, detecting three-phase sequence, and conducting RCD (Residual Current Device) tests.

PEAKMETER PM8200A/B Voltage and Continuity Tester in a wet environment, highlighting IP65 waterproof and dustproof rating.
Figure 1: PEAKMETER PM8200A/B demonstrating its IP65 waterproof and dustproof capabilities.
Image detailing the multifunctional features of the PEAKMETER PM8200A/B, including voltage, continuity, three-phase sequence, and RCD tests.
Figure 2: Overview of the multifunctional capabilities of the PM8200A/B.

2. Setup and Initial Inspection

2.1 Unpacking and Contents

Upon receiving your PEAKMETER PM8200A/B, carefully unpack the contents and verify that all items are present and in good condition. The standard package for PM8200A includes:

  • PEAKMETER PM8200A/B Instrument
  • Color box/blister packaging
  • User Manual (this document and a PDF version)
  • Storage bag
Diagram showing accessories for PM8200A: instrument, color box/blister packaging, instruction manual, and storage bag.
Figure 3: PM8200A accessories and packaging.

2.2 Battery Installation

The PM8200A/B requires 2 x 1.5V AAA batteries (not included). To install or replace batteries:

  1. Locate the battery compartment on the back of the instrument.
  2. Open the battery cover.
  3. Insert two 1.5V AAA batteries, ensuring correct polarity (+/-).
  4. Close the battery cover securely.

2.3 Initial Check

Before first use, inspect the instrument for any visible damage. Turn on the device to ensure it powers on and displays information correctly. If any abnormalities are observed, do not use the instrument and contact customer support.

3. Operating Instructions

3.1 General Operation

  • Power On/Off: The instrument features an automatic shutdown function, turning off after approximately 30 seconds of no measurement activity to conserve battery. Press any key to wake it up.
  • Display: The device utilizes an analog and digital display for clear readings.
  • Buttons: The operation panel includes an LED screen, RCD test button, HOLD button, and Lighting button for various functions.
  • Low Battery Reminder: An indicator will appear on the display when the battery level is low.
  • Silent Mode (PM8200B only): The PM8200B model offers a silent mode, allowing you to switch between beeping and muting as needed.
Diagram of the PM8200B operation panel, labeling LED screen, RCD test button, HOLD button, and Lighting button, along with display icons and their meanings.
Figure 4: PM8200B Operation Panel and Display Icons.
Image showing the automatic shutdown feature of the tester after 30 seconds of inactivity.
Figure 5: Automatic Shutdown Feature.
Image illustrating the silent mode feature of the PM8200B model, showing a muted speaker icon.
Figure 6: Silent Mode (PM8200B only).

3.2 Voltage Measurement (AC/DC)

The PM8200A/B offers a wide range for both AC and DC voltage measurements, up to 1200V AC and 1500V DC respectively. Simply connect the probes to the circuit or component you wish to measure. The instrument will automatically detect the voltage type and display the reading.

Image highlighting the high precision and wide measurement range of the tester, up to 1200V AC and 1500V DC.
Figure 7: High Precision and Wide Voltage Range.
Series of images demonstrating practical operations: measuring alternating voltage, DC voltage (1500V), and performing a continuity test.
Figure 8: Practical Demonstration of AC/DC Voltage Measurement.

3.3 Continuity Test

To perform a continuity test, connect the probes across the circuit or component. A beeping sound and visual indication on the display will confirm if the line is conducting. This is useful for checking circuit integrity.

Video 1: Demonstration of Continuity Test and other functions. The video shows the tester indicating continuity with a beeping sound and visual feedback.

3.4 Phase Sequence Detection

The instrument can detect the phase sequence of three-phase AC systems within a range of 150V to 400V (50Hz-60Hz). The display will simultaneously show voltage and frequency, along with 'R' or 'L' indicators for phase rotation. Note that strong electric fields may affect test results.

Diagram showing phase sequence detection with 'R' and 'L' indicators on the tester's display, testing between 150V and 400V.
Figure 9: Phase Sequence Detection.

3.5 RCD Testing

Perform a one-click RCD test to simulate a leakage situation and verify if the RCD system is functioning correctly, providing essential safety checks.

Image showing the RCD jump test in progress, simulating a leakage situation to check RCD system functionality.
Figure 10: RCD Jump Test.

3.6 Voltage Detection Without Battery

Even without battery power, the PM8200A/B can perform simple voltage detection. If the detected voltage exceeds 50V, the LED at the bottom of the flashlight will illuminate, with brightness increasing with higher voltage. This ensures basic safety checks are always possible.

Image demonstrating simple voltage detection without battery power, showing the flashlight illuminating when voltage exceeds 50V.
Figure 11: Voltage Detection Without Battery Power.

4. Maintenance

4.1 Cleaning

To maintain the accuracy and longevity of your instrument, keep it clean. Wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents.

4.2 Storage

After each use, store the PM8200A/B in a dry and cool environment, free from corrosive gases. Ensure the probes are properly secured and the instrument is protected from physical damage.

4.3 Battery Replacement

When the low battery indicator appears on the display, replace the batteries promptly to ensure accurate measurements. Refer to section 2.2 for battery installation instructions.

Image showing the low battery reminder icon on the tester's display.
Figure 12: Low Battery Reminder.

5. Troubleshooting

  • Instrument does not power on: Check if the batteries are installed correctly and have sufficient charge. Replace batteries if necessary.
  • Inaccurate readings: Ensure probes are making good contact with the test points. Verify that the instrument is not operating in a strong electric field, which can affect results.
  • Automatic shutdown during use: The instrument has an auto-off feature. If it shuts down unexpectedly, press any button to reactivate it. If it continues to shut down frequently, check battery levels.
  • No continuity indication: Ensure the circuit is de-energized before testing continuity. Check for open circuits or faulty components.

6. Specifications

Table 1: PEAKMETER PM8200A Specifications
SpecificationRangeAccuracy
AC Voltage12V, 24V, 50V, 120V, 230V, 400V, 690V, 1000V, 1200V±(1.0% + 3)
DC Voltage12V, 24V, 50V, 120V, 230V, 400V, 690V, 1000V, 1500V±(1.0% + 3)
Continuity<100kΩ Buzzing LED Indication
FrequencyHz
Phase Sequence TestThree-phase AC voltage range: 150V-400V, frequency 50Hz-60Hz
RCD TestingYes
FlashlightYes
Automatic ShutdownYes
BacklightingYes
Auto RangingYes
Resistance MeasurementYes
IP DegreeIP65
Battery2 x 1.5V AAA batteries (not included)
Product Size250mm x 80mm x 34mm
Product Weight305g (not including batteries)
Safety Standard/RatingEN61326-1, EN60529, IEC 61243-3, CAT IV 600V
Specification table for PEAKMETER PM8200A, detailing voltage ranges, accuracy, features, and general information like battery, size, weight, and safety ratings.
Figure 13: PM8200A Parameter Table.
Specification table for PEAKMETER PM8200B, detailing voltage ranges, accuracy, features, and general information like battery, size, weight, and safety ratings.
Figure 14: PM8200B Parameter Table.
Table explaining IPXX dust and water resistance ratings, showing IP65 means completely dustproof and resistant to water flushing.
Figure 15: IPXX Dust and Water Resistance Rating Explanation.

7. User Tips

  • Safety First: Always prioritize safety when working with electricity. Ensure you understand the circuit you are testing and take appropriate precautions. The CAT IV 600V rating indicates high safety for industrial use.
  • Leverage IP65 Rating: Don't hesitate to use the PM8200A/B in challenging environments. Its IP65 rating means it's completely dustproof and protected against water jets, making it suitable for outdoor or damp conditions.
  • PM8200B Silent Mode: If you have the PM8200B model, utilize the silent mode feature when working in noise-sensitive areas or when audible alerts are not desired.
  • Check for Strong Electric Fields: Be aware that strong electric fields can influence phase sequence detection results. If you suspect interference, try to minimize external electrical noise.

8. Warranty and Support

For detailed warranty information and technical support, please refer to the official product documentation or contact the seller directly. A comprehensive user manual in PDF format is available for download:

Download User Manual (PDF)

If you encounter any issues or have questions not covered in this manual, please reach out to the manufacturer's customer service or your point of purchase for assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.