JINKA GC-1351CAM

Contents

JINKA GC-1351CAM Cutter Plotter Instruction Manual

Model: GC-1351CAM

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your JINKA GC-1351CAM Cutter Plotter. Designed for precision and ease of use, this machine features a stepper motor, automatic contour cutting with multi-point positioning, and support for offline operation via USB. Please read this manual thoroughly to ensure safe and efficient use of your equipment.

JINKA GC-1351CAM Cutter Plotter on its stand

Figure 1: JINKA GC-1351CAM Cutter Plotter

2. Setup

2.1 Unpacking and Assembly

  1. Carefully remove all components from the packaging.
  2. Assemble the iron alloy stand according to the included diagrams (if separate assembly instructions are provided, refer to those).
  3. Mount the cutter plotter unit securely onto the assembled stand.
  4. Ensure the media basket is properly attached to the stand.
Iron alloy stand for the plotter

Figure 2: Plotter Stand

2.2 Power Connection

Connect the power cable to the plotter's power input port and then to a compatible AC power outlet (AC85V-AC264V, 50Hz/60Hz). Use the power switch to turn the unit on/off.

Close-up of the power switch and input port

Figure 3: Power Switch and Input

2.3 Computer and Software Connection

Connect the plotter to your computer using either the COM or USB interface. Install the necessary cutting software (e.g., Anycut, CorelDRAW, Flexi12, Signcut) on your computer. The plotter supports common engraving languages.

Rear view of the plotter showing COM and USB ports

Figure 4: Interface Ports (COM, USB, U disk)

2.4 Media Loading

Load your desired cutting material (e.g., vinyl, lightbox film) onto the plotter. Ensure the material is aligned correctly and secured by the all-in-one pinch rollers to prevent shifting during operation. The maximum paper width supported is 1260mm.

Close-up of the pinch rollers

Figure 5: Pinch Rollers

3. Operating Instructions

3.1 Basic Operation

The plotter features a touch screen control panel with an English display for easy navigation. Use the interface to set parameters and initiate cutting jobs.

Close-up of the touch screen control panel

Figure 6: Touch Screen Control Panel

3.2 Contour Cutting

The GC-1351CAM supports automatic contour cutting with multi-point positioning. The integrated HD camera scans mark points on your printed material to ensure precise cuts along the contours of your designs.

Video 1: Demonstration of Contour Cutting

3.3 Offline Operation

For convenience, you can perform cutting jobs directly from a USB flash disk without needing a computer connection. Prepare your cutting files on the USB disk and insert it into the plotter's USB port.

3.4 Adjusting Cutting Parameters

  • **Cutting Force:** Adjust the cutting force between 5-500g depending on the material thickness and type.
  • **Cutting Speed:** Set the cutting speed from 5-800mm/s to match your project requirements and material.
Close-up of the cutting carriage with laser for contour cutting

Figure 7: Cutting Carriage with Laser

4. Maintenance

  • **Regular Cleaning:** Keep the plotter clean from dust and debris. Use a soft, dry cloth to wipe down the exterior.
  • **Roller Maintenance:** Periodically inspect and clean the barbed steel feed rollers to ensure optimal grip and prevent material slippage.
  • **Blade Inspection:** Check the cutting blade regularly for sharpness and replace it when dull to maintain cutting precision.
  • **Environmental Conditions:** Operate the plotter in an environment with a temperature range of +5°C to +35°C and relative humidity of 30%-70% to ensure longevity and performance.

5. Troubleshooting

  • **Plotter Not Responding:** Check power connections, USB/COM cable connections, and ensure the plotter is turned on.
  • **Inaccurate Cuts:** Verify media alignment, check blade condition, and ensure calibration for contour cutting is correctly performed.
  • **Material Slippage:** Ensure pinch rollers are clean and applying adequate pressure. Check for any obstructions on the feed path.
  • **Software Communication Issues:** Reinstall drivers, check cable connections, or try a different USB/COM port.
  • **Offline Job Failure:** Ensure the USB flash disk is properly formatted and the cutting files are in a compatible format.

6. Specifications

FeatureSpecification
ModelGC-1351CAM
Max. Paper Width1350mm
Max. Plotting Width1240mm
Max. Cutting Speed800mm/s
Max. Cutting Force500g
DriverStepper motor
Control Panel + DisplayTouch screen, English display
Memory32M
CarriageAlloy single position carriage with camera
Feeding RollerBarbed steel feed roller
InterfaceCOM + USB + U disk, support offline job
Repeatability0.127mm
Power SupplyAC85V-AC264V, 50Hz/60Hz
Operating EnvironmentTemperature: +5°C to +35°C, Relative Humidity: 30%-70%
StandIron alloy stand with media basket
TypeHand Tool Parts
Place of OriginAnhui, China
Software CompatibilityAnycut/CorDRAW/Flexi12/Signcut
Command SetDMPL/HPGL

7. User Tips

  • Always perform a test cut on a small piece of your material to fine-tune the cutting force and speed settings before starting a large project.
  • Ensure your material is free of wrinkles or bubbles before loading to achieve the best cutting results.
  • Regularly update your cutting software and drivers to ensure compatibility and access to the latest features.
  • When using the contour cutting feature, make sure the registration marks are clearly printed and free from smudges for accurate scanning by the HD camera.

8. Warranty and Support

Your JINKA GC-1351CAM Cutter Plotter is manufactured by Hefei Kaxing Digital Control Equipment Co., Ltd., a leading manufacturer with over 20 years of experience in CNC products. For technical support, service inquiries, or any questions regarding your product, please contact our support team:

  • Telephone: +86-18056579771
  • Email: Sales06@cnjinka.com
  • WeChat: +86 19119251865

We are committed to providing excellent service and support for our products.

Contact information for support

Figure 8: Contact Information

© 2024 JINKA. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.