Flipsky Mini FSESC6.7 Pro 70A

Contents

Flipsky Mini FSESC6.7 Pro 70A Electronic Speed Controller User Manual

Model: Mini FSESC6.7 Pro 70A | Brand: Flipsky

1. Introduction

The Flipsky Mini FSESC6.7 Pro 70A is a high-performance Electronic Speed Controller (ESC) designed for electric skateboards, e-bikes, and other applications utilizing brushless DC motors. Based on the VESC®6.6 platform, it offers advanced control capabilities and features an aluminum anodized heat sink for efficient thermal management. This manual provides essential information for the safe and effective use of your Mini FSESC6.7 Pro 70A.

2. Safety Instructions

  • Always disconnect the battery before performing any maintenance or wiring changes.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Operate the ESC within its specified voltage and current limits. Overloading can cause damage or fire.
  • Keep the ESC away from water, moisture, and extreme temperatures.
  • Handle with care; electronic components are sensitive to static discharge.
  • Mount the ESC in a well-ventilated area to ensure proper heat dissipation.

3. Package Contents

Please check the package for the following items:

  • Flipsky Mini FSESC6.7 Pro 70A Electronic Speed Controller
  • Power input wires (red and black, pre-soldered)
  • Motor phase wires (three black wires, pre-soldered)
  • Signal cable harness
Overall view of the Flipsky Mini FSESC6.7 Pro 70A with all primary connections
Overall view of the Flipsky Mini FSESC6.7 Pro 70A with all primary connections: thick red and black wires for battery input, three thick black wires for motor phase connections (labeled A, B, C), and a smaller multi-pin signal cable for control.

4. Specifications

FeatureDetail
Model NumberMini FSESC6.7 PRO
Max Continuous Current70A
Software BaseVESC®6.6
Heat ManagementAluminum Anodized Heat Sink
Capacitors3 x 220uF 100V
OriginMainland China
Approx. Package Length20 cm
Approx. Package Width20 cm
Approx. Package Height10 cm
Approx. Package Weight1.0 kg

5. Setup Guide

Follow these steps to set up your Flipsky Mini FSESC6.7 Pro 70A:

  1. Mounting: Securely mount the ESC to your electric skateboard or device chassis. Ensure the aluminum heat sink has adequate airflow for cooling.
  2. Motor Connection: Connect the three thick black motor phase wires (labeled A, B, C on the ESC) to your brushless DC motor's phase wires. The order may affect motor direction, which can be adjusted in software.
  3. Battery Connection: Connect the thick red wire from the ESC to the positive (+) terminal of your battery and the thick black wire to the negative (-) terminal. Double-check polarity before connecting to avoid damage.
  4. Receiver/Control Connection: Connect the signal cable harness from the ESC to your receiver or control unit. Refer to your receiver's manual for correct pin assignments (e.g., PPM, UART).
  5. Configuration (VESC Tool):
    • Download and install the VESC Tool software on your computer.
    • Connect the ESC to your computer using a USB-C cable via the USB-C port on the ESC.
    • Launch the VESC Tool and follow the on-screen instructions to detect and configure your ESC. This typically involves motor detection, input setup (e.g., remote control), and setting current limits.
Top view of the Flipsky Mini FSESC6.7 Pro 70A board with connections
Top view of the Flipsky Mini FSESC6.7 Pro 70A, showing the main circuit board, three 220uF 100V capacitors, power input wires (red/black), motor phase wires (black), and various signal connectors including a USB-C port.
Close-up of the connector ports on the Flipsky Mini FSESC6.7 Pro 70A
Close-up of the connector ports on the Flipsky Mini FSESC6.7 Pro 70A, including the USB-C port for configuration, and several JST-style connectors for various peripherals like UART, PPM, and CAN bus.

6. Operating Instructions

Once the ESC is properly installed and configured:

  1. Power On: Connect your battery to the ESC. The ESC should power on, indicated by any status LEDs (if present).
  2. Control Input: Use your remote control or other input device to send commands to the ESC. The motor should respond according to your configuration.
  3. Monitoring: For advanced users, the VESC Tool can be used to monitor real-time data such as motor RPM, current, voltage, and temperature during operation.
  4. Power Off: Disconnect the battery from the ESC when not in use.

7. Maintenance

  • Regular Inspection: Periodically check all wiring and connectors for signs of wear, corrosion, or loose connections.
  • Cleaning: Keep the ESC clean and free from dust, dirt, and debris. Use a soft, dry brush or compressed air. Do not use liquids.
  • Thermal Management: Ensure the heat sink remains unobstructed to allow for proper cooling. Overheating can reduce performance and lifespan.
  • Firmware Updates: Check the official Flipsky website or VESC project for firmware updates. Updating firmware can improve performance and add new features.
Side view of the Flipsky Mini FSESC6.7 Pro 70A heat sink
Side view of the Flipsky Mini FSESC6.7 Pro 70A, highlighting the aluminum anodized heat sink for efficient thermal management.

8. Troubleshooting

  • ESC not powering on: Check battery connections and ensure the battery is charged. Verify power switch (if used) is in the ON position.
  • Motor not spinning/erratic behavior: Re-check motor phase wire connections. Ensure the signal cable from the receiver is correctly connected and the remote control is paired and functioning. Re-run motor detection in VESC Tool.
  • Overheating: Ensure the ESC is mounted in a location with good airflow. Reduce continuous current draw if possible, or consider additional cooling solutions.
  • Connection issues with VESC Tool: Ensure the USB-C cable is functional and properly connected. Try a different USB port on your computer. Verify VESC Tool is the correct version for your firmware.

9. User Tips

  • Always perform a bench test before riding your electric skateboard to ensure all components are working correctly and safely.
  • Start with conservative settings in the VESC Tool and gradually increase parameters as you become more familiar with the ESC's performance.
  • Consider using a loop key or anti-spark connector for your battery to prevent large current spikes during connection.

10. Warranty and Support

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty validation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.