1. Introduction
The Hantek TO1000 series is a new generation of multi-functional full touch screen tablet oscilloscopes. Designed for portability and durability, it features a thin body, light weight, and a unique hanging design for hands-free operation, making it anti-falling and anti-seismic. This versatile device integrates an oscilloscope, multimeter, signal generator, and spectrum analyzer into one unit. It boasts a built-in large-capacity battery for extended endurance and supports fast charging via a standard 18W Type-C charger.
The device features a multi-touch 7-inch LCD screen with a resolution of 800x480, offering a friendly and easy-to-use interface for a good interaction experience.

2. Safety Information
Always operate the device in accordance with the instructions provided in the user manual. Ensure proper handling of probes and connections to avoid electrical shock or damage to the device. Do not expose the device to extreme temperatures, humidity, or corrosive environments. Only use the provided charging equipment or compatible Type-C 18W fast chargers. Refer to the detailed PDF user manual for comprehensive safety guidelines.
For a complete and detailed user manual, please refer to the official PDF document: Hantek TO1000 Series User Manual (PDF)
3. Device Overview
3.1 Front Panel

The front panel is dominated by the 7-inch multi-touch LCD screen. On the left side, there are dedicated buttons for HOME, OSC (Oscilloscope), DMM (Digital Multimeter), AFG (Arbitrary Function Generator), H/R (Hold/Run), and PRINT functions.
3.2 Side and Top Panels



The device includes USB Host and USB Device interfaces for connectivity. The top panel features BNC connectors for oscilloscope channels (CH1-CH4) and an AFG output for models with signal generator functionality. The side panel houses input jacks for the digital multimeter.
4. Initial Setup
4.1 Charging the Battery
The TO1000 series oscilloscope comes with a built-in super large capacity lithium battery (7500mAh). Before initial use, it is recommended to fully charge the device. Use the provided 18W Type-C charger or any compatible fast charger. The charging port is located on the side of the device. A full charge ensures long endurance, with standby time up to half a year.
4.2 Power On/Off
Press and hold the power button (usually located on the side or top) to turn the device on or off. The multi-touch screen will display the boot-up sequence.
4.3 Adjusting the Kickstand
The unique suspension foot design allows for multi-angle adjustment, providing stability and optimal viewing during operation. Simply pull out the kickstand from the back of the device and adjust it to your desired angle.
5. Operation
The TO1000 series features a full touch screen interface for intuitive operation. Most functions can be accessed and controlled directly via touch gestures and on-screen menus.

5.1 Oscilloscope Function (OSC)
Press the 'OSC' button on the left panel to enter oscilloscope mode. Use the touch screen to adjust settings such as vertical sensitivity (V/div), time base (s/div), trigger type, and coupling. Connect probes to the BNC input channels (CH1-CH4) on the top panel.
5.2 Digital Multimeter Function (DMM)
Press the 'DMM' button to switch to digital multimeter mode. Connect multimeter leads to the dedicated input terminals on the side panel. Select the desired measurement function (e.g., DC Voltage, AC Current, Resistance) from the on-screen menu. The DMM provides high-precision measurements with data recording, storage, trend charts, and statistical analysis.
5.3 Arbitrary Function Generator (AFG)
For 'D' models, press the 'AFG' button to access the signal generator. Select from a variety of built-in standard waveforms (Sine, Square, Ramp, Pulse, Noise, DC) or arbitrary waveforms. Adjust parameters such as frequency (up to 25MHz), amplitude, offset, and duty cycle using the touch interface. Connect the output from the AFG BNC connector on the top panel.
5.4 Waveform Storage
The device supports one-key waveform storage for convenience. You can store up to 4 sets of reference waveforms, 4 sets of settings, and 4 sets of captured waveforms.
6. Maintenance
6.1 Cleaning
To clean the device, use a soft, dry cloth. For stubborn dirt, a slightly damp cloth with mild detergent can be used, ensuring no liquid enters the ports or buttons. Do not use abrasive cleaners or solvents.
6.2 Battery Care
To prolong battery life, avoid fully discharging the battery frequently. If storing the device for an extended period, ensure the battery is charged to approximately 50-70% and store in a cool, dry place. Recharge periodically if stored for very long durations.
6.3 Software Updates
Check the official Hantek website periodically for any available firmware updates to ensure optimal performance and access to new features.
7. Troubleshooting
7.1 Device Not Powering On
- Ensure the battery is sufficiently charged. Connect the device to the charger and wait a few minutes before attempting to power on again.
- Verify the power button is pressed and held correctly.
7.2 No Waveform Displayed
- Check probe connections to the BNC input channels and the circuit under test.
- Ensure the oscilloscope is in 'OSC' mode.
- Adjust vertical sensitivity (V/div) and time base (s/div) settings to match the expected signal characteristics.
- Verify trigger settings are appropriate for the signal.
- Check input coupling (DC, AC, GND) is set correctly.
7.3 Multimeter Readings Incorrect
- Ensure multimeter leads are correctly inserted into the DMM input terminals.
- Verify the correct measurement function (voltage, current, resistance, etc.) is selected.
- Check the range setting; if auto-ranging is off, select an appropriate range.
7.4 Signal Generator Not Outputting
- Ensure the device is a 'D' model (e.g., TO1154D, TO1204D, TO1254D) which includes the AFG function.
- Verify the AFG output is connected correctly.
- Check that the AFG function is enabled and parameters (frequency, amplitude) are set to non-zero values.
8. Specifications

8.1 Model Overview
| Model | Oscilloscope Channels | Bandwidth | Sampling Rate | Storage Depth | Signal Source | Multimeter |
|---|---|---|---|---|---|---|
| TO1112 | 2 CH | 110 MHz | 250MSa/S | 8M | - | - |
| TO1112C | 2 CH | 110 MHz | 250MSa/S | 8M | - | √ |
| TO1112D | 2 CH | 110 MHz | 250MSa/S | 8M | √ | √ |
| TO1154C | 4 CH | 150 MHz | 1GSa/s | 8M | - | √ |
| TO1204C | 4 CH | 200 MHz | 1GSa/s | 8M | - | √ |
| TO1254C | 4 CH | 250 MHz | 1GSa/s | 8M | - | √ |
| TO1154D | 4 CH+1CH | 150 MHz | 1GSa/s | 8M | 25MHz | √ |
| TO1204D | 4 CH+1CH | 200 MHz | 1GSa/s | 8M | 25MHz | √ |
| TO1254D | 4 CH+1CH | 250 MHz | 1GSa/s | 8M | 25MHz | √ |
| TO1152C | 2 CH | 150 MHz | 1GSa/s | 8M | - | √ |
| TO1202C | 2 CH | 200 MHz | 1GSa/s | 8M | - | √ |
| TO1252C | 2 CH | 250 MHz | 1GSa/s | 8M | - | √ |
| TO1152D | 2 CH+1CH | 150 MHz | 1GSa/s | 8M | 25MHz | √ |
| TO1202D | 2 CH+1CH | 200 MHz | 1GSa/s | 8M | 25MHz | √ |
| TO1252D | 2 CH+1CH | 250 MHz | 1GSa/s | 8M | 25MHz | √ |
8.2 Oscilloscope (Common Specifications)
- Input Coupling: DC, AC, GND
- Input Impedance: 1MΩ ±2%, in parallel with 15pF ±5pF
- Max Input Voltage: 400V (DC+AC Peak)
- Vertical Resolution: 8 bit
- Vertical Sensitivity: 2mV/div - 10V/div
- Time Base Range: 2ns/div - 1000s/div
- Trigger Types: Edge, Pulse, Video, Slope, Timeout, Window, Pattern, Interval, Runt, UART, LIN, CAN, SPI, IIC
- Cursor Measurement: ΔV, ΔT, 1/ΔT
- Automatic Measurement: Max, Min, Pk-Pk, Top, Base, Amp, Avg, Mean, RMS, CursRMS, Duty Cycle, Period, Freq, Rise Time, Fall Time, +Width, -Width, +Duty, -Duty, Delay A→B↑, Delay A→B↓, Phase A→B↑, Phase A→B↓, FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF
- Waveform Math: +, -, *, /, FFT
- Waveform Storage: 4 sets of reference waveforms, 4 sets of settings, 4 sets of waveforms
- Interface: USB Host, USB Device, Pass/Fail
8.3 Digital Multimeter (DMM) Specifications
- DC Voltage: 60mV, 600mV, 6V, 60V, 600V, 1000V
- AC Voltage: 60mV, 600mV, 6V, 60V, 600V, 750V
- DC Current: 60mA, 600mA, 6A, 10A
- AC Current: 60mA, 600mA, 6A, 10A
- Resistance: 600Ω, 6kΩ, 60kΩ, 600kΩ, 6MΩ, 60MΩ
- Capacitance: 40nF, 400nF, 4uF, 40uF, 400uF, 4mF
- Diode Test: Yes
- Continuity Test: Yes
8.4 Signal Generator (AFG) Specifications (for 'D' models)
- Output Channels: 1 CH
- Sample Rate: 200 MSa/s
- Vertical Resolution: 12 bit
- Max Output Frequency: 25 MHz
- Standard Waveforms: Sine, Square, Ramp, Pulse, Noise, DC
- Arbitrary Waveforms: Exp Rise, Exp Fall, Sin(x)/x, Step, Multi-tone, Lorentz, etc.
8.5 General Specifications
- Display: 7-inch TFT LCD, 800x480 resolution, Multi-touch screen
- Battery: Built-in Lithium battery, 7500mAh
- Charging: Type-C, 18W fast charging
- Dimensions: 248mm x 176mm x 54mm
- Weight: Approx. 1.2 kg
- Operating Environment: 0°C to 50°C, Humidity ≤90% RH
- Storage Environment: -20°C to 70°C, Humidity ≤90% RH
9. Warranty and Support
9.1 Warranty Information
All products are checked and packed in good condition before dispatching. The Hantek TO1000 series oscilloscope comes with a one-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.
9.2 Contact Support
For any questions, technical assistance, or warranty claims, please contact customer service:
- WhatsApp: +86 15244291916
- Email: 773875441@qq.com
- Office Tel: 0086-755-27541660
- Cellphone: 0086-15967476818
- Trademanager: cn901815702
All inquiries will be replied to within 24 hours.

10. User Tips
- Maximize Battery Life: Utilize the 18W fast charging feature, but for long-term storage, keep the battery charged to around 50-70% to preserve its health.
- Portability: Take advantage of the unique hanging design and kickstand for flexible positioning in various work environments.
- Touch Screen Efficiency: Familiarize yourself with the multi-touch gestures for quick navigation and parameter adjustments, enhancing your workflow.
- Data Management: Regularly save important waveforms and settings using the one-key storage function to prevent data loss.