1. Introduction
Thank you for choosing the intelamp YL002-12A1PK Outdoor Solar Security Flood Light. This manual provides essential information for the safe and efficient use of your new solar light. Please read it thoroughly before installation and operation, and keep it for future reference.
The intelamp solar security flood light is designed to provide bright, wide-angle illumination for outdoor areas such as yards, gardens, garages, pathways, and streets. It features high-efficiency solar panels, a large-capacity lithium battery, and dual motion sensors for enhanced security and energy efficiency.
2. Important Safety Information
WARNING: Please read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
- Potential Fire Risk: Strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with applicable legal requirements.
3. Product Features
- Wide Arc Lighting Area: Three adjustable lamp heads provide an industry-leading 270° wide-angle illumination.
- High-Efficiency Solar Panels: Equipped with high-power solar panels for efficient energy absorption and fast charging.
- High-Capacity Battery: Built-in 6000mAh lithium iron phosphate battery ensures long lighting duration, up to 3 consecutive nights in motion-sensing mode after a full day of charging.
- Bright Illumination: Delivers a bright and consistent output of 1200 lumens.
- Dual Motion Sensors: Two motion sensors provide a wide detection range of over 180°, detecting motion from both front and sides for comprehensive coverage.
- Adjustable Design:
- Middle lamp head: Adjustable vertically (up and down) by 45 degrees.
- Side lamp heads: Adjustable horizontally (left to right) by up to 90 degrees.
- Solar panel: Adjustable vertically (up and down) by 60 degrees. An optimum tilt angle of 20 degrees is recommended for efficient charging and rainwater cleaning.
- Durable Construction: Made with ABS body material and rated IP65 for protection against dust and water.



4. Setup and Installation
The intelamp solar security light is designed for easy, self-contained installation. No complex wiring is required.
4.1 Unpacking and Preparation
- Carefully remove the solar light from its packaging.
- Remove all protective films from the solar light casing and the solar panel.
- Ensure the solar panel is unobstructed and free of stains or debris.
4.2 Choosing an Installation Location
Select a location that receives direct sunlight for at least 6-8 hours daily to ensure optimal charging. The location should be unobstructed by trees, buildings, or other objects that might cast shadows on the solar panel.
- Recommended Installation Height: 1.8 - 2.5 meters (approximately 6 - 8 feet) from the ground.
- Suitable Areas: Walls, wooden fences, garage door frames, trees, or posts.
4.3 Installation Steps
Each package includes screws and tie straps for installation.
- Marking: Hold the light fixture in the desired installation spot and mark the positions for the mounting holes.
- Drilling (for screws): Drill holes at the marked positions. Insert wall anchors if necessary.
- Mounting with Screws: Align the light fixture with the drilled holes and secure it using the provided screws.
- Mounting with Cable Ties (alternative): For installation on trees or posts, thread the provided cable ties through the designated slots on the light fixture and secure it tightly around the object.
- Adjusting the Light Heads and Solar Panel:
- Adjust the middle lamp head vertically (up/down) by up to 45 degrees.
- Adjust the side lamp heads horizontally (left/right) by up to 90 degrees.
- Adjust the solar panel vertically (up/down) by up to 60 degrees. Aim for an approximate 20-degree tilt to maximize sun exposure and allow rainwater to clean the panel.


5. Operation
5.1 Initial Power On and Charging
- Power On: Locate the power switch on the side or bottom of the light fixture. Switch it to the "ON" position to turn it on.
- Automatic Charging: No manual charging is required. Once powered on, place the light fixture in direct sunlight. The solar panel will automatically absorb sunlight and store electrical energy in the built-in lithium battery.
- Charging Duration: 6-8 hours of sufficient direct sunlight can provide 8-12 hours of nighttime lighting. Actual duration depends on weather conditions and sunlight intensity.

5.2 Lighting Modes
After turning on the light, cover the solar panel (to simulate darkness) and press the "MODE" button to cycle through the available lighting modes. The light has three distinct modes:
- Mode 1 (Sensor Mode - High Brightness with Low Dim): The light stays on at a low brightness setting continuously. When motion is detected, it will illuminate brightly. After approximately 30 seconds of no motion, it returns to low brightness.
- Mode 2 (Sensor Mode - High Brightness Only): The light remains off. When motion is detected, it will illuminate brightly. After approximately 30 seconds of no motion, it turns off completely.
- Mode 3 (Constant Low Brightness Mode): The light stays on at a low brightness setting throughout the night, with the motion sensors inactivated.

6. Maintenance
- Cleaning the Solar Panel: Regularly wipe the solar panel with a soft, damp cloth to remove dust, dirt, leaves, or snow. A clean panel ensures maximum sunlight absorption and charging efficiency.
- Battery Care: The built-in lithium iron phosphate battery has a service life of more than 5 years. No user maintenance is required for the battery.
- General Cleaning: Clean the light fixture periodically to remove any accumulated dirt or debris.
- Inspection: Periodically check the light fixture and its mounting for any signs of damage or loose connections. Address any issues promptly.
- Winter Care: In areas with heavy snowfall, ensure the solar panel is cleared of snow to allow for charging.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on at night. |
|
|
| Motion sensor is not working or is too sensitive. |
|
|
| Light duration is shorter than expected. |
|
|
8. Specifications
| Feature | Detail |
|---|---|
| Brand Name | intelamp |
| Model Number | YL002-12A1PK |
| Power Source | SOLAR |
| Installation Method | Self-contained |
| Light Source | LED bulbs |
| Brightness | 1200 Lumens |
| Voltage | 5V |
| Is Bulbs Included | Yes |
| Is Dimmable | Yes |
| Solar Cell Type | Lithium battery (6000mAh capacity) |
| Is Batteries Included | Yes |
| Protection Level | IP65 |
| Body Material | ABS |
| Use | Industrial (suitable for various outdoor applications) |
| Origin | Mainland China |
| Style | Modern Style |
| Certification | CE, FCC, GS, LVD, ROHS, UL |
| Product Dimensions (approx.) | Solar Panel: 9.4 x 4.3 inches; Light Unit: 12 inches wide |
| Package Dimensions (approx.) | Length: 26 cm, Width: 15 cm, Height: 14 cm |
| Package Weight (approx.) | 0.933 kg |

9. User Tips
- Optimal Placement: For best performance, ensure the solar panel is positioned to receive maximum direct sunlight throughout the day. Even partial shading can significantly reduce charging efficiency.
- Mode Selection: Experiment with the three lighting modes to find the one that best suits your needs for security and energy saving. Mode 1 (dim + bright on motion) offers a good balance for continuous low-level lighting with motion-activated brightness.
- Sensor Sensitivity: If the motion sensor is triggering too often due to environmental factors (e.g., pets, moving branches), try adjusting the angle of the light heads to narrow the detection area.
- Initial Charge: Before first use, allow the light to charge for a full day (6-8 hours) in direct sunlight to ensure the battery is fully charged.
10. Warranty and Support
The intelamp YL002-12A1PK Solar Security Flood Light comes with a 1-year warranty from the date of purchase.
For technical support, warranty claims, or any questions regarding your product, please contact:
- Manufacturer: Shenzhen Jindian Electronic Technology Co., Ltd.
- Email: service@intelamp.com
- EU Authorized Representative: SUCCESS COURIER SL
- Email: successservice2@hotmail.com
Please have your model number (YL002-12A1PK) and proof of purchase ready when contacting support.
A detailed user manual in PDF format is also available for download. Please refer to the product page or contact support for the link: User manual (PDF)
