1. Introduction and Safety Warnings
Thank you for purchasing the Baofeng UV-5R Mini. This dual band, dual display, dual watch radio provides secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation.
1.1. Regulatory Conformance
As certified by qualified laboratories, this product complies with essential requirements and relevant provisions of Directive 1999/5/EC (2014/53/EU) and other applicable EU regulations (2006/66/EC, 2011/65/EU, 2012/19/EU). This information is applicable to EU countries only.
1.2. FCC Part 15 / IC Compliance
This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
1.3. RF Exposure Warning
It is the user's responsibility to properly operate this radio transmitter to ensure safe operation. Please adhere to the following guidelines:
- Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Contact your local dealer for a replacement antenna.
- Hand-Held Operation (Held-to-Face): This device was evaluated for typical hand-held operations with a 1-inch spacing from the front of the radio. For compliance with FCC RF exposure requirements, hold the radio 1 inch from your face.
- Body-Worn Operation: This device was evaluated for body-worn operations with the supplied belt-clip accessory. All necessary accessories are included. Third-party accessories (unless approved by the manufacturer) should be avoided as they might not comply with FCC RF exposure guidelines.
1.4. Precautions for Portable Terminals
To protect against property loss, bodily injury, or death, observe the following safety instructions:
- Do not operate the product in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials. Only approved Ex-protection models are allowed in such locations, and any attempt to assemble or disassemble is strictly prohibited.
- Do not operate near blasting areas.
- Do not operate near medical or electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate in areas where wireless communication equipment is completely prohibited.
2. Package Contents
The standard package includes the following items:
| Item | Quantity (PCS) | Item | Quantity (PCS) |
|---|---|---|---|
| Radio | 2 | Lanyard | 2 |
| Battery | 2 | Operation Manual | 1 |
| Antenna | 2 | Belt Clip | 2 |
| Type-C Cable | 2 | Box | 1 |
*Note: Charger and power adapter are subject to the final configuration of the dealer. The charging instructions in this manual may not be appropriate if Type-C charging method is used.
3. Product Overview
The Baofeng UV-5R Mini is designed for ease of use and portability. Below are the key features and components.

Figure 3.1: Mini Shape, Ultra-thin Body. Suitable for Police, Outdoor Rescue, Maritime Transport, and Hotel use. Features 2200mAh Battery Capacity, Type-C Charging, and 999 Channels.

Figure 3.2: Product Dimensions. Height (with antenna): 18.3CM/7.2Inch. Body Height: 10.8CM/4.25Inch. Width: 4.8CM/1.89Inch. Depth: 3.5CM/1.38Inch.
Figure 3.3: Key Features Overview. Includes Mini Case, Bluetooth read-write frequency, Dual PTT key design, 999 channels, One-Touch Frequency Pairing, Multi-segment scanning reception, Adjustable high and low power, FM function, and Type-C charging.
3.1. Radio Components (Refer to OCR Page 9 Diagram)
- Antenna
- SK1-Customized Function Keys/Monitor button
- PTT-A Button
- OK/Menu button
- V/M-VFO/MR
- PTT-B Button
- Numeric Keypad
- Flashlight
- Volume/Power Knob
- Screen
- Accessory Port
- Cancel/Back button
- ▲ Up button/▼Down button
- A/B
- Microphone
- LED Indicator
- Battery Latch
- Type-C Charging indicator light
- Type-C Charging Port
- Search/Flashlight button
4. Initial Setup
4.1. Attaching the Antenna
Turn the antenna clockwise until it is tight. To remove the antenna, turn it counterclockwise.
CAUTION:
- Do not hold the radio antenna in your hand during operation, as this will reduce performance and antenna life.
- Do not shake the radio with the top of the antenna in your hand, as this will degrade performance and antenna life.
4.2. Charging the Battery
When using the terminal for the first time, a low battery warning may occur. It is recommended to turn off the radio during charging. The battery's LEDs provide an indication of the current state of charge:
| Indicator light | Charging status |
|---|---|
| Red light is always on | Charging |
| Green light is always on | Charging complete |
The radio supports Type-C USB charging, allowing convenient charging via USB chargers, computers, power banks, or car chargers.

Figure 4.1: Type-C Charging options (USB Charging, Computer charging, Power Bank Charging, Car Charger).
5. Basic Operations
5.1. Turning Your Radio On and Off
- To turn your radio ON, turn the [Volume/Power] rotary knob clockwise.
- To turn your radio OFF, turn the [Volume/Power] rotary knob counterclockwise.
5.2. Setting the Volume
- Increase volume by turning the [Volume/Power] rotary knob clockwise.
- To decrease volume, turn the [Volume/Power] rotary knob counterclockwise.
CAUTION:
Do not hold the radio close to your ear if the volume is set to an uncomfortable level, as it could cause hearing damage.
5.3. Locking or Unlocking Keypad
To avoid accidentally changing radio settings:
- Press and hold the [*] key to lock the keypad until the screen displays the "lock" icon.
- In lock mode, you can turn the intercom on and off, adjust the volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
- To unlock the keypad, press and hold the [*] key again until the "lock" icon is no longer displayed.
6. Advanced Operations
6.1. Keypad Entry
You can enter radio aliases, channel aliases, numbers, etc., using the radio's numeric keypad.
- To switch between input methods, press [# ↑ ] key.
- Press 1 to enter a special character (except in numeric input mode).
- Press 0 to enter a space (except in numeric input mode).
6.2. Select a Channel
The channel is where the signal is transmitted. Press the [V/M] button to toggle between VFO and channel mode. Then, press the ▲/▼ buttons or use the rotary encoder to select the desired channel. To enter a channel number directly, use the keypad (e.g., enter "064" for channel 64).
6.3. Channel Memory
In Frequency and Standby mode, you can store frequencies and parameters:
- Press [MENU] [3] [MENU] [1] [5]. The screen will display "MEMCH".
- Press [MENU] to enter the function.
- Press the ▲/▼ buttons to select the channel, then press [MENU] to store it. A sound tone will confirm success.
- Press [EXIT] to return to standby mode.
NOTE:
If you want to set CTCSS tones, DCS codes, or the frequency offset, do so before storing the channel. Stored channels are displayed as CH-, other channels have no CH- display.
6.4. Delete a Channel (DEL-CH)
In VFO mode and standby mode:
- Press [MENU] [3] [MENU] [1] [6]. The screen will display "DELCH".
- Press [MENU] to enter the function.
- Press the ▲/▼ buttons or rotate the encoder to select the channel you want to delete, then press [MENU] to confirm.
- Press [EXIT] to return to standby mode.
NOTE: Channel 1 cannot be deleted.
6.5. Main Band/Sub Band Switch
In standby mode, press the [A/B] key to toggle between the A and B bands. The highlighted band is the main band; the darker displayed band is the sub-band.
6.6. VFO/Channel Switch
Press the [V/M] button to switch between VFO and channel display. VFO mode will display the 'VFO' icon. MR mode will display the channel serial number.
6.7. Setting the VFO Frequency
Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.
- Operation 1: Input the VFO frequency directly with the keypad.
- Operation 2: Press the ▲/▼ button or use the rotary encoder to adjust the VFO frequency in the set frequency step.
6.8. Call Service (Transmitting and Receiving)
All radios in the group must be set to the same channel and sub-code to communicate. To ensure optimal reception volume, keep the microphone 2.5 cm to 5 cm from your mouth when transmitting.
- Initiate a call: Select a channel, then press and hold the [PTT-A] key. The radio transmits on segment A (upper screen), and the red indicator light is on. Speak into the microphone with a normal voice. Alternatively, press and hold the [PTT-B] key to transmit on the B segment (lower screen).
- Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light is on.
6.9. Emergency Alarm
The emergency alarm function allows the terminal to initiate an alarm to seek help. In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.
6.10. Flashlight
In standby mode, press the preset [8] key to turn the flashlight on or off.
6.11. FM Radio Function
Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1. Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. The screen displays the tuning frequency. Operations:
- Press ▲/▼ key to search for radio channels at the preset step frequency.
- Press the [# ↑ ] key to search for radio channels automatically. The screen displays 'SEEK...'.
- Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
- Press SK1 key [FM Radio] to exit radio mode.

Figure 6.1: FM/AM Radio Functionality.
6.12. Monitor
Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. You can also adjust the volume level. Release the [Monitor] key to exit.
6.13. Frequency Search
Press the pre-programmed [SEARCH] key or press and hold [8] key. The radio enters frequency search state, displaying "SEARCH...". Press [# ↑ ] key to switch the searching band (VHF/UHF, etc.). The frequency and CTCSS/DCS code will be displayed after searching is completed. Press [MENU] to save the channel.
6.14. Reverse Frequency Function
Short press the [*] key in relay mode to invert the receive and transmit frequencies. The screen shows the 'R' icon. This function is often used in repeater channels when there is a frequency difference between receive and transmit frequencies.
6.15. Talk Around Function
In repeater mode, press [*] to switch between Talkaround Mode and Repeater Mode. The screen displays 'T' and 'R' icons. In Talkaround mode, the receive frequency equals the transmit frequency.
6.16. Repeater Activation Tone
Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.
6.17. Voice-activated Transmit (VOX)
Enable VOX to transmit automatically via voice, without pressing PTT. It stops transmitting when speech stops. To enable VOX:
- In Standby status, press [MENU][2][MENU][4] to enter Vox Switch.
- Press [MENU][2][MENU][5] to enter Vox Level. Press ▲/▼ to select VOX level (1-9). A smaller value means higher sensitivity. The 'V' icon is displayed. Default is off.
- Press [MENU] to save the setting and return to the upper menu.
To turn off VOX, select OFF OFF, and the 'V' icon disappears.
6.18. Dual Watch
In Dual Watch mode, the radio can receive frequencies set for channel A or B.
- Press [MENU] [2] to enter Radio Set.
- Press [MENU] + ▲ to select "15 Dual Watch".
- Press [MENU] key to enter Dual Watch Setting, press ▲/▼ key to select "On".
- Press [MENU] key to save and return. The 'D' icon will be displayed.
To turn off, select "Off", and the 'D' icon disappears. The sub-band displays the "dual watch" icon.
6.19. Stopwatch Function
Press and hold the [MENU] key to enable the stopwatch. Operations:
- Press [MENU] to start.
- Press [MENU] again to stop.
- Press [EXIT] to exit.
6.20. Weather Radio/Scan Weather Channel
Your radio has NOAA Weather Radio and Scan functions.
- To turn NOAA Weather Scan on, press and hold the [0] key for 3 seconds. The "weather" icon appears, and the radio enters Weather band mode.
- Press and hold the [# ↑ ] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding [# ↑ ] again stops the scan.
- After stopping NOAA weather scan, manually select the weather channel by pressing ▲ or ▼ key.
- To exit Weather Radio broadcast mode, press the "weather" key or [PTT] key.
NOTE:
Weather Channels Wx 1 Thru 10 are receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| CH-01 | 162.550 | CH-06 | 162.500 |
| CH-02 | 162.400 | CH-07 | 162.525 |
| CH-03 | 162.475 | CH-08 | 161.650 |
| CH-04 | 162.425 | CH-09 | 161.775 |
| CH-05 | 162.450 | CH-10 | 163.275 |
7. Programming the Radio
7.1. Bluetooth APP Programming
You can program the radio wirelessly using a dedicated APP. Before programming, download and install the "Programmer-APP" on your Android or iOS device.

Figure 7.1: Bluetooth Programming. Easily read and write frequency settings, simplifying traditional programming.

Figure 7.2: Scan QR codes to download the programming software for Android and iOS.
Steps for APP Programming:
- Press [MENU] + [4] to enter Wireless CPS.
- Press [MENU] + ▲/▼ to select "On". The Bluetooth icon will be displayed on the first line of the screen.
- Open the radio APP on your smartphone. Allow Bluetooth and location services.
- Select the walkie-talkie model "5Rmini Series" and connect to the radio.
- Click "Walkie-talkie" in the app. A "connection success" prompt will appear, and you can return to the home page to program.
Programming Functions within the APP:
- Read the radio data: After reading the frequency, click "program" to enter program details. You can program channel information, frequency mode, and optional functions.
- Save Profile: Save the programmed profile as a new profile. If you select "Replace Program", click it to save.
- Write data to radio: From the home page, select "program", click "Write" to write the frequency. The radio will restart automatically upon completion.
7.2. Wireless Copy Frequency
This feature allows you to quickly copy frequencies from another radio.

Figure 7.3: Wireless Copy Frequency. Simplifies the process of setting up communication between two radios.
Steps for Wireless Copy Frequency:
- Press the [SEARCH] button to enter the "SEARCH" interface.
- Press [SEARCH] again, and the radio will search for another radio's transmission frequency and privacy code.
- Finally, press the [MENU] button to store the frequency.
This allows two walkie-talkies to communicate normally without traditional manual frequency input.
9. Technical Specifications
The Baofeng UV-5R Mini offers a range of features and robust performance. Below are the detailed technical specifications.
9.1. General Features
- 6 band scan receiver: FM78-108MHz; AM108-136MHz; VHF136-174MHz, 220-260MHz; UHF400-520MHz, 350-390MHz
- Transmit frequency: VHF 144-148MHz; UHF420-450MHZ
- RF output: 5W/2W, dual PTT transmitter
- Wireless read/write frequency
- Display: 1.44" TFT large screen, full keyboard, full open menu operation
- Channel Memory: 999 channels, local channel storage and deletion
- Frequency Input: Full keyboard manual frequency input
- Pairing: One-click frequency pairing, easy pairing and grouping
- Relay function settings: frequency difference, frequency difference direction, relay activation audio settings
- Alarm function: Three types of alarm settings for security
- Input method: Built-in, supports local editing of channel name, receiving frequency, transmitting frequency
- DTMF: Encoding and decoding function, 20 DTMF calls
- Frequency hopping function
- Side button customization: radio, scan, sweep, voice control, flashlight, alarm
- FM radio function: Receive frequency 78~108MHz
- Keypad lock: Automatic or manual, backlight selection
- Charging: Support Type-C charge
9.2. Detailed Technical Parameters
| Parameter | Value |
|---|---|
| Receiver Frequency | FM 76-108 MHz; VHF 136-174MHz, UHF 400-520MHz, 350-390MHz |
| Transmission Frequency | VHF 144-148MHz, UHF 420-450MHz |
| Channel Spacing | 25.0KHz(Wide)/12.5KHz(Narr) |
| Memory Channel | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Dimensions | 108mm×52mm×37mm (No antenna) |
| Weight | 200g (Battery pack included) |
| Transmission current | ≤1600mA |
| Receive Sensitivity | 0.25μV (12dB SINAD) |
| Rated Audio Power Output | 1W @16 ohms |
| Receive current | ≤380mA |
| Connection for accessories | 2 pin Kenwood jack |
| Antenna impedance | 50 Ohm |
| Maximum Range | 3km-5km |
| Battery Capacity | 2200mAh |
| Waterproof Rating | IP45 |
| Material | Plastic |
| Certifications | CE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee |
NOTE: All specifications may be modified without prior notice or liability.
10. Maintenance
Your Two Way Radio is an electronic product of exact design and should be treated with care. The following suggestions will help you maintain your product and prolong its life.
10.1. General Care
- Do not attempt to open the radio for any reason. The radio's precision mechanics and electronics require specialized equipment. Unauthorized opening will void the warranty.
- Do not store the radio under direct sunlight or in hot areas. High temperatures can shorten the life of electronic devices and warp or melt plastics.
- Do not store the radio in dusty and dirty areas.
- Keep the radio dry. Rainwater or dampness will corrode electronic circuits.
- If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
- Do not transmit without an antenna.
- Operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation. In this case, place it in a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify, or repair the product and its accessories without authorization.
10.2. Battery Maintenance
To help your battery work normally and prolong its life, observe the following instructions:
- Accumulated dust on the charging connector may affect normal charging. Use a clean and dry cloth to wipe it regularly.
- It is recommended to charge the battery between 5°C and 40°C. Violation of this limit may cause battery life reduction or leakage.
- To ensure a full charge, turn off the radio when charging a battery attached to the product.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time or place it close to other heating sources.
- Do not squeeze or penetrate the battery, nor remove its housing.
11. Troubleshooting
This section provides solutions to common issues you might encounter with your Baofeng UV-5R Mini.
| Problem | Possible Cause | Solution |
|---|---|---|
| Radio does not turn on | Battery is depleted or not properly installed. | Charge the battery fully. Ensure the battery is securely latched. |
| Poor reception or transmission quality | Damaged antenna, incorrect frequency/channel settings, low battery, obstructions. | Check antenna for damage and replace if necessary. Verify frequency and channel settings. Ensure battery is charged. Move to an open area. |
| Cannot program via Bluetooth APP | Bluetooth not enabled, location services off, incorrect app, radio not in Wireless CPS mode. | Ensure Bluetooth and location services are enabled on your phone. Use the correct "Programmer-APP". Put the radio into Wireless CPS mode ([MENU] + [4], then "On"). |
| Keypad is locked | Keypad lock function is active. | Press and hold the [*] key to unlock the keypad. |
| Radio overheats during use | Continuous transmission for extended periods. | Reduce transmission time. Allow the radio to cool down in a well-ventilated area. |
| Battery drains quickly | Power Save mode is off, high transmission power, frequent use. | Enable Power Save mode (Menu 2, Power Save: ON). Use lower transmission power when possible. |
12. User Tips
Based on user feedback, here are some tips to enhance your experience with the Baofeng UV-5R Mini:
- Audio Quality: Users report excellent audio quality for both reception and transmission. Ensure your microphone is 2.5-5 cm from your mouth for optimal clarity.
- Battery Life: The battery holds up well even at high power settings. For extended use, consider carrying a power bank and Type-C cable for convenient recharging.
- Overheating: The radio generally does not overheat, even during prolonged conversations. However, avoid continuous transmission for excessively long periods to prevent heat buildup.
- Programming: The Bluetooth APP programming feature is highly praised for its speed and convenience. It simplifies frequency input and channel editing significantly.
- Chirp Compatibility: For advanced users, the radio can also be programmed using Chirp software, offering more customization options.
- Portability: Its small size and lightweight design make it very easy to carry, perfect for outdoor activities or professional use.
- Screen: The color screen is a notable feature, providing clear visibility of channels and settings.
13. Warranty and Support
We promise to carefully 100% inspect quality, specification and quantity of the items before delivery.
We offer ONE YEAR WARRANTY for the radio body, and THREE MONTHS for the battery, charger, and other accessories.
Please contact the seller for any warranty claims or support inquiries. Do not attempt to open or repair the radio yourself, as this will void the warranty.
14. Disclaimer
The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With continuous technological development, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, or dissemination of this handbook may be made in any form without prior written authorization from our department.
Print version: 5R Mini_V1.0