JASIC WSME-200 (E201II)

Contents

JASIC WSME-200 (E201II) Pulse AC/DC TIG Welder Instruction Manual

Model: WSME-200 (E201II)

1. Introduction

Thank you for choosing the JASIC WSME-200 (E201II) Pulse AC/DC TIG Welder. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your welding machine. Please read this manual thoroughly before operating the equipment to ensure proper use and to prevent injury or damage.

Front view of the JASIC WSME-200 (E201II) TIG Welder

Figure 1: Front view of the JASIC WSME-200 (E201II) TIG Welder

2. Safety Information

WARNING: Welding can be dangerous. Always follow safety precautions to prevent serious injury or death.

  • Always wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
  • Ensure adequate ventilation to avoid inhaling welding fumes.
  • Protect bystanders from arc rays and hot metal.
  • Ensure the welding machine is properly grounded.
  • Do not operate in wet conditions or near flammable materials.
  • Disconnect power before performing any maintenance or service.
  • Read and understand all safety warnings and instructions provided with your welding consumables and accessories.

3. Product Overview

The JASIC WSME-200 (E201II) is a versatile Pulse AC/DC TIG Welder designed for high-quality welding of various metals, including carbon steel, stainless steel, and aluminum alloys. It features advanced IGBT inverter technology for stable arc performance and precise control.

Key Features:

  • TIG Welding: Provides precise control for delicate and high-quality welds.
  • Pulse AC/DC: Offers flexibility for welding different materials and thicknesses.
  • MMA Welding: Also supports Stick (MMA) welding for general fabrication.
  • IGBT Module: Ensures stable output and high efficiency.
  • High Frequency Arc Initiation: For reliable arc starts without contamination.
  • Remote Control Capability: Allows for convenient adjustment during welding.
Diagram highlighting key features: TIG Welding, Pulse AC/DC, MMA Welding, and IGBT Module

Figure 2: Key features of the WSME-200 (E201II)

Included Accessories:

  • Earth Clamp
  • TIG Torch
  • Consumables (e.g., collets, collet bodies, ceramic nozzles)
  • User Manual
JASIC WSME-200 (E201II) TIG Welder with included accessories

Figure 3: Welder and standard accessories

4. Specifications

ParameterValue
ModelWSME-200 (E201II)
Supply VoltageSingle-phase AC220V +15%
Rated Input Capacity6 kVA
Power Factor0.7
Rated No-Load Voltage60 V
TIG Welding Current Range10~200 A
AC Output Frequency20~250 Hz
Cleanup Width20~60%
Base Current10~200 A
Pulse Frequency (DC)0.5~200 Hz
Pulse Frequency (AC)0.5~25 Hz
Front Blowing Time0~5 s
Back Blowing Time0~15 s
Rise Time0~15 s
Decay Time0~15 s
Remote ControlYes
Arc Initiation ModeHigh Frequency Arc Initiation
MMA Welding Current Range10~160 A
Thrust Current (MMA)0~40 A
Thermal Arc Initiation Current (MMA)0~80 A
Rated Duty Cycle @40℃25%
Inverter Welders Efficiency85%
Protection LevelIP21S
Insulation LevelH
Dimensions (L*W*H)541*232*410 mm
Weight12.9 kg
Materials ProcessedCarbon steel, Stainless steel, Aluminium alloy
ApplicationWelding steel, iron, titanium, copper, nickel, Aluminum Tig Welding

5. Setup

5.1 Unpacking and Inspection

  1. Carefully remove the welding machine and all accessories from the packaging.
  2. Inspect for any visible damage that may have occurred during transit. Report any damage to your supplier immediately.
  3. Ensure all components listed in the 'Included Accessories' section are present.

5.2 Power Connection

  • The machine requires a single-phase AC220V (+15%) power supply.
  • Ensure the power outlet is properly grounded and can handle the rated input capacity of 6 kVA.
  • Connect the power cable to the machine's input terminal and then to the power supply.
Rear view of the JASIC WSME-200 (E201II) TIG Welder, showing power input and switch

Figure 4: Rear panel with power input

5.3 Welding Circuit Connections

  1. Earth Clamp: Connect the earth clamp cable to the appropriate terminal on the front panel (usually marked with a ground symbol or '-'). Secure the earth clamp to the workpiece, ensuring good electrical contact.
  2. TIG Torch: Connect the TIG torch to the designated TIG torch connector on the front panel. Ensure all connections are tight.
  3. Gas Connection: For TIG welding, connect your shielding gas (e.g., Argon) cylinder to the gas inlet on the rear of the machine using a suitable regulator and hose. Ensure all gas connections are leak-free.
Close-up of the control panel on the JASIC WSME-200 (E201II) TIG Welder

Figure 5: Front panel connections and controls

6. Operating Instructions

6.1 Control Panel Overview

The front panel features a digital display and various controls for setting welding parameters. Refer to Figure 5 for a visual guide. Key controls include:

  • Mode Selection: Switch between TIG (AC/DC, Pulse) and MMA welding modes.
  • Current Adjustment: Knob for setting welding current (10-200A for TIG, 10-160A for MMA).
  • AC Output Frequency: Adjusts the AC frequency for TIG welding (20-250 Hz).
  • Cleanup Width: Controls the cleaning action for AC TIG welding (20-60%).
  • Pulse Settings: Adjust pulse frequency (DC: 0.5-200 Hz, AC: 0.5-25 Hz), base current, rise time, and decay time.
  • Gas Pre/Post Flow: Set front blowing time (0-5s) and back blowing time (0-15s).
  • Remote Control Interface: For connecting optional remote control devices.

6.2 TIG Welding Operation (AC/DC Pulse)

  1. Power On: Flip the main power switch on the rear panel to 'ON'.
  2. Select TIG Mode: Use the mode selector to choose the desired TIG welding mode (AC TIG for aluminum, DC TIG for steel/stainless steel).
  3. Set Parameters: Adjust welding current, AC frequency (for AC TIG), pulse settings (if using pulse), and gas pre/post flow times according to the material and thickness.
  4. Prepare Torch: Ensure the TIG torch has a sharp tungsten electrode and appropriate consumables.
  5. Start Welding: Initiate the arc using the high-frequency start. Maintain a consistent arc length and travel speed.
  6. Observe Weld: Monitor the weld puddle and adjust parameters as needed for optimal results.

Video 1: Product overview and demonstration of the JASIC WSME-200 (E201II) TIG Welder.

Close-up of a TIG weld bead

Figure 6: Example of a TIG weld

Close-up of an aluminum TIG weld

Figure 7: Example of an Aluminum TIG weld

6.3 MMA Welding Operation

  1. Power On: Flip the main power switch on the rear panel to 'ON'.
  2. Select MMA Mode: Use the mode selector to choose MMA welding mode.
  3. Set Parameters: Adjust welding current (10-160A), thrust current (0-40A), and thermal arc initiation current (0-80A) based on the electrode type and material.
  4. Connect Electrode Holder: Connect the electrode holder cable to the appropriate terminal (usually '+' for most electrodes) and the earth clamp to the other terminal.
  5. Prepare Electrode: Insert the appropriate electrode into the holder.
  6. Start Welding: Strike the arc by lightly touching and quickly withdrawing the electrode from the workpiece.
Close-up of an MMA weld bead

Figure 8: Example of an MMA weld

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your welding machine.

  • Cleaning: Regularly clean the machine's exterior and ventilation openings to prevent dust and debris buildup. Use compressed air to blow out internal components periodically, ensuring the machine is unplugged.
  • Cable Inspection: Inspect all welding cables, torch, and earth clamp for damage, cuts, or loose connections before each use. Replace damaged components immediately.
  • TIG Torch Maintenance: Regularly check and replace worn tungsten electrodes, collets, collet bodies, and ceramic nozzles. Keep the torch clean.
  • Gas System: Check gas hoses and connections for leaks. Ensure the gas cylinder is securely fastened.
  • Storage: Store the welding machine in a clean, dry environment when not in use.

8. Troubleshooting

This section outlines common issues and their potential solutions. For problems not listed here, contact technical support.

ProblemPossible CauseSolution
No powerPower switch off, loose power cable, circuit breaker trippedTurn on switch, check cable connections, reset breaker
No arc (TIG)No gas flow, contaminated tungsten, poor earth connection, incorrect settingsCheck gas supply, sharpen tungsten, ensure good earth, verify settings
Unstable arcIncorrect current, dirty workpiece, worn tungsten, improper gas flowAdjust current, clean workpiece, replace/sharpen tungsten, check gas
Poor weld qualityIncorrect parameters, dirty material, improper technique, wrong filler metalReview settings, clean material, practice technique, use correct filler
Overheating indicator onExceeded duty cycle, blocked ventilationAllow machine to cool, clear ventilation openings

9. User Tips

  • Tungsten Preparation: Always grind your tungsten electrode to a sharp point for DC TIG welding. For AC TIG, a balled tip is often preferred, but a slightly blunted point can also work well.
  • Gas Flow: Ensure your shielding gas flow rate is appropriate for the nozzle size and welding current. Too little gas leads to contamination, too much can cause turbulence.
  • Workpiece Cleanliness: For TIG welding, especially aluminum, thorough cleaning of the workpiece is crucial. Remove all oxides, oils, and contaminants.
  • Practice: Welding requires practice. Start with scrap material to dial in your settings and refine your technique before working on critical projects.
  • Duty Cycle: Be mindful of the machine's duty cycle (25% at 40°C). This indicates how long the machine can weld continuously at maximum current within a 10-minute period before needing to cool down.

10. Warranty and Support

The JASIC WSME-200 (E201II) TIG Welder comes with a three-year warranty, ensuring quality and reliability.

For any questions regarding the product, technical assistance, or warranty claims, please contact your seller or the manufacturer's support channels. You can typically reach support via:

  • Email: bft001002@126.com
  • WhatsApp/Wechat: +86 185 7086 4505

When contacting support, please have your product model (WSME-200 E201II) and any relevant purchase information ready.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.