Botslab G980H / G980H PRO / 980h Mount

Contents

Botslab Dash Cam Mount User Manual

Model: G980H / G980H PRO / 980h Series

1. Product Overview

This document provides detailed instructions for the installation, use, and maintenance of the Botslab Dash Cam Mount. This mount is designed to securely attach your compatible Botslab dash camera to your vehicle's windshield, ensuring stable recording performance.

Botslab G980H Dash Cam Mount and Dash Cam Outline

Figure 1: Botslab G980H Dash Cam Mount (Dash cam not included)

2. Package Contents

Please check the package contents upon receipt to ensure all items are present:

  • 1 x G980H Mount
  • 3 x Static Electricity Stickers
  • 3 x Sticker Mounts
Package Contents: Static Electricity Stickers, Sticker Mounts, and G980H Mount

Figure 2: Included components in the package

3. Compatibility

This mount is compatible with the following Botslab Dash Cam models:

  • Botslab G980H
  • Botslab G980H PRO
  • Botslab 980h

Important Note: This mount is NOT compatible with the Botslab G980H 4 Channel Dashcam. Please verify your dash cam model before installation.

Incompatible Model Warning for Botslab G980H 4 Channel Dashcam

Figure 3: Incompatible dash cam model (G980H 4 Channel Dashcam)

4. Setup Instructions

Follow these steps carefully for proper installation. Improper use may affect product performance.

4.1 Static Cling Installation Requirements

  • When installing the static cling, avoid the position behind the rearview mirror with black dots. It needs to be installed on a transparent glass surface.
  • Keep the glass surface clean during installation. Do not apply any substances (including water, alcohol, etc.) to the glass.
  • The static cling is for one-time use only and is not reusable. If there are a few small bubbles when installing, they will automatically disappear over time.

4.2 3M Glue Installation Tutorial

  • First, check if there is any residual glue that has not been cleaned from the position where the glue is to be applied. It will not stick if not cleaned properly (do not touch the glue surface directly with your hands).
  • Check to see if the size of the 3M glue is the same as the area where it is to be attached. If it is too large, it will not stick. If it is slightly smaller, it is not a problem. If the sizes are different, you will need to trim it to the same size as the glue area.
  • When installing the 3M glue, make sure to press it down firmly after attaching. After attaching it, leave it for 24 hours before attaching it to the glass.
  • When the temperature is low, you can use the car's air conditioner or other methods to heat the 3M glue before use for better results.

4.3 General Use Steps

  • Clean the installation position to be pasted; use a clean dry towel or paper towel.
  • Peel off the protective film of the static cling; apply it to the transparent windshield.
  • Stick the recorder to the static sticker and press hard for 60 seconds.
  • Exhaust the air from the static cling sticker.
  • After installation, do not move the recorder again. The adhesive of the sticker becomes more and more firm with time.

Warning: Static cling cannot be pasted on the rearview mirror black grid!

5. Operating Instructions

Once installed, ensure the dash cam is securely attached to the mount. The mount provides a stable platform for your dash cam's operation. Periodically check the mount's adhesion to the windshield, especially after significant temperature changes or prolonged use.

6. Maintenance

To maintain optimal performance and adhesion:

  • Regularly clean the windshield area where the mount is attached to prevent dust and debris buildup.
  • Avoid exposing the mount to extreme temperatures for extended periods, as this may affect the adhesive.
  • If re-installation is necessary, use a new static cling sticker and 3M adhesive for best results.

7. Troubleshooting

7.1 Common Reasons for Static Sticker Falling Off

  • The black dot grid behind the rearview mirror was not avoided during installation.
  • The glass surface was not cleaned during installation, leading to dust, glue residue, or oil stains.
  • The installation was repeated (it should be pasted at one time, not repeatedly).

7.2 Common Reasons for 3M Adhesive Falling Off

  • The pasting surface was not cleaned up properly.
  • The size of the 3M glue is different from that of the pasting equipment (generally, the pasting surface of the equipment is uneven, and all four sides are protruding, which will lead to incomplete bonding if not trimmed).
  • The time after pasting was not long enough, and it was not completely bonded (the effect of 3M glue is better after 24 hours).

8. Specifications

FeatureSpecification
Item TypeCar DVR Accessory (Mount)
Assembly ModePortable Recorder (for compatible dash cams)
Dimensions (Approx.)12 cm (Length) x 12 cm (Width) x 3 cm (Height)
Weight (Approx.)0.03 kg
Batteries IncludedNo
OriginMainland China

9. User Tips

  • Always double-check the compatibility of the mount with your specific Botslab dash cam model before purchase and installation.
  • Ensure the installation surface (windshield) is thoroughly cleaned and dry for optimal adhesion of the static cling and 3M glue.
  • Allow the 3M adhesive to cure for at least 24 hours before attaching the dash cam to ensure a strong bond.

10. Warranty & Support

For any questions, technical support, or warranty inquiries regarding your Botslab Dash Cam Mount, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact information.

A PDF version of this user manual may be available for download from the seller's product page or support website.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.