1. Introduction
Thank you for choosing the TrackerKing EC08 GPS Tracker. This device is designed for reliable real-time tracking and monitoring of vehicles, supporting BDS/GPS/GNSS/LBS positioning technology. It offers microsecond positioning, low latency data transmission, and various alarm mechanisms to enhance vehicle security. The EC08 is suitable for a wide range of applications, including car loans, logistics, and electric vehicle anti-theft.
Please read this manual carefully to ensure smooth and correct operation of your device. Specifications and information are subject to change without prior notice.
2. Setup
2.1 Package Contents
Before installation, please verify that all components are present:
- 1 x EC08 GPS Tracker
- 1 x Power Wire
- 1 x Built-in Battery (integrated)
- 1 x User Manual
2.2 SIM Card Installation
- Open the device case.
- Properly insert a GSM SIM card into the SIM card slot. Ensure the small switch inside the SIM card hole is turned ON after insertion.
- Close the device case.
Important Notes for SIM Card:
- Insert the SIM card BEFORE turning the device power switch on.
- The SIM card must have GPRS function enabled.
- Ensure the SIM card has sufficient balance.
2.3 Initial Power-On and Positioning
- After inserting the SIM card, connect the external power supply.
- Place the device outdoors in an open area.
- Within approximately 30 seconds, three indicator lights will illuminate steadily, indicating the device is working normally and has acquired a GPS fix.
2.4 Installation Attentions
NOTE: The device's front side must face the sky for optimal GPS signal reception.
When installing in a car, be aware that a metal thermal insulation layer or heating layer on the windshield can reduce the GPS signal, potentially leading to GPS work disorder. Choose an installation location that minimizes obstruction to the sky view.
2.5 Device Wiring Requirements
The EC08 GPS tracker requires connection to the vehicle's power system. Refer to the diagram below for correct wiring. The device operates on 9-90V.
- Red Wire: Connect to positive (+) terminal of the vehicle battery (9-80V), typically through a 2A fuse.
- Black Wire: Connect to negative (-) terminal or ground of the vehicle battery.
- Yellow Wire: Connect to ACC (Accessory) ignition detection.
- Orange Wire: Connect to the relay for remote cut-off functionality.
- Green Wire: Connect to the oil pump for remote cut-off functionality (via relay).
- White Wire: (If applicable) Additional signal wire.
3. Operating Instructions
3.1 Device Light Description
The device uses indicator lights to communicate its status:
| Light | Represents |
|---|---|
| Yellow | GSM signal normal |
| Blue | GPS signal normal |
| Red | Power |
3.2 TrackerKing Tracking Platform and APP
The EC08 GPS Tracker can be monitored via a web-based platform or a dedicated mobile application. The official web platform is www.trackerking.net.
For mobile access, search for “Tracker King” in the Google Play Store or Apple App Store to download the official application.
3.3 How to Log In to the Platform (APP)
- Select Server: Tracker King
- User: Enter the ID number found on your device.
- Password: The default password is
123456. It is highly recommended to change this password immediately after your first login for security purposes.
3.4 Key Operating Features
- Real-time Tracking: Monitor your vehicle's current location in real-time via the web platform or mobile app.
- History Route Playback: Review the historical movement track of your vehicle. Data is retained for up to six months and can be queried by date.
- Geo-fence: Set up virtual boundaries. Receive alerts if the vehicle enters or exits a defined area.
- Overspeed Alarm: Configure speed limits and receive notifications if the vehicle exceeds them.
- Vibration Alarm: Get alerts if the device detects abnormal vibration, indicating potential tampering or unauthorized movement.
- Remote Cut-off Engine/Oil: In case of theft or unauthorized use, remotely disconnect the vehicle's fuel and electricity supply to stop the engine.
- Power Failure Alarm: The internal battery activates and sends an alert if the main power supply is disconnected.
- Remote OTA: Support for upgrading built-in programs remotely.
4. Maintenance
4.1 General Care
- Keep the device dry. Moisture can damage the electronic circuits.
- Avoid extreme temperatures. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt plastic parts.
- Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. Wipe it with a soft, damp cloth.
- Handle the device with care. Do not drop, knock, or shake it. Rough handling can break internal circuit boards and fine mechanics.
4.2 SIM Card Maintenance
- Regularly check the SIM card balance to ensure continuous GPRS functionality and tracking.
- Ensure the SIM card is always active and has a valid data plan.
5. Troubleshooting
5.1 Common Issues and Solutions
- No GPS Signal / GPS Work Disorder:
- Ensure the device's front side is facing the sky.
- Check for obstructions like metal thermal insulation layers on the windshield. Relocate the device if necessary.
- Ensure the device is placed outdoors for initial GPS fix.
- Device Not Powering On:
- Verify the external power supply connections are secure and correct (Red to +, Black to -).
- Check the 2A fuse in the power wire.
- Ensure the small switch inside the SIM card hole is in the ON position.
- No Data Transmission / Offline:
- Confirm the SIM card is correctly inserted and the small switch is ON.
- Ensure the SIM card has GPRS function enabled and sufficient balance.
- Check if the yellow (GSM) indicator light is normal.
- Login Issues on APP/Platform:
- Verify the server selected is "Tracker King".
- Double-check the User ID (device ID number) and password.
- If you forgot your password, contact customer service for assistance.
5.2 SMS Command List
The EC08 GPS Tracker supports various functions via SMS commands. Send these commands from a registered phone number to the device's SIM card number.
| Number | Functional Item | SMS Command | Command Reply |
|---|---|---|---|
| 1 | Restore initial settings (except IP, port, APN) | FORMAT | FORMAT |
| 2 | APN query | APN# | Reply: APN:cmnet,, |
| 3 | APN set | APN,cmnet,,# or APN,cmnet,aaa,bbb# | Command example: APN,cmnet,,# (Cmnet is APN, no user name/password). Example: APN,cmnet,internet,cmnet# (Cmnet is APN, internet is APN user name, cmnet is APN password) |
| 4 | Server parameter query | SERVER# | Reply: SERVER:0,103.44.239.119,8011,0 |
| 5 | Server parameter settings | 1. Set domain name: SERVER,1,domain name,port,0# 2. Set IP: SERVER,0,IP,port,0# (Last 0 represents TCP) | SMS:SERVER,0,154.23.114.25,8011,0# Reply: SERVER:0,154.23.114.25,8011,0 |
| 6 | Address query (abroad) | URL# | <03-20 22:45>http://maps.google.com/maps?q=+22.601862,+113.832383 |
| 7 | Status query | STATUS# | Battery:4.23V;GPRS:Offline;GSMSignal Level:25;ACC:OFF;GPS:OFF;Defense:ON; |
| 8 | Query parameter settings | PARAM# | IMEI:123456781911111;TIMER:10,3600;SNEDS:3;HBT:180Sec;Defense:2; |
| 9 | Restart command | RESET# | Reply: RESET OK |
| 10 | Query oil and electricity control status | RELAY# | Reply: RELAY:0 |
| 11 | Oil and electricity control | RELAY,1# (1 disconnect oil and electricity) RELAY,0# (0 turn on oil and electricity) | Reply: RELAY 1 OK |
| 12 | Add center number 1 | CENTER,A,center number# | SMS: CENTER,A,8618575518750# Reply: CENTER,A:8618575518750 (86 is China country code) |
| 13 | Delete center number 1 | CENTER,D# | Reply: CENTER Del OK |
| 14 | Add center number 2 | CENTER,A2,center number# | SMS: CENTER,A2,8618007931238# Reply: CENTER,A2:8618007931238 |
| 15 | Delete center number 2 | CENTER,D2# | Reply: CENTER D2 Del OK |
| 16 | Add center number 3 | CENTER,A3,center number# | SMS: CENTER,A3,8613912345678# Reply: CENTER,A3:8613912345678 |
| 17 | Delete center number 3 | CENTER,D3# | Reply: CENTER D3 Del OK |
| 18 | Query center number | CENTER# | Reply: CENTER,A:8618575518750 CENTER,A2:8618007931238 CENTER,A3:8613912345678 |
| 19 | Add SOS number | SOS,A,number 1,number 2,number 3# | SOS,A,8618575518750# SOS,A,8613912345678,8618007931238# SOS,A,8613912345678,8613912345678,8613912345678# Option to set 1 or more numbers at a time |
| 20 | Delete SOS number | SOS,D,1# SOS,D,1,2# SOS,D,1,2,3# Option to delete 1 or more numbers at a time | SOS,D,1# SOS,D,1,2# SOS,D,1,2,3# |
| 21 | Query SOS number | SOS# | Reply: SOS:8613912345678,8613912345678,8613912345678 |
| 22 | Allow auto answering | 777# | Reply: Automatic incoming call answering has been set. After setting, the device will answer the call automatically after any number. |
| 23 | Disable automatic answering | 888# | Reply: Automatic incoming call answering has been Close. After setting, the device will answer the call automatically after SOS or center number (default: forbidden). |
| 24 | Set the incoming call function | SZCS#CALL_FUN=A | A=0 voice monitoring function after incoming calls (default, needs device support microphone). A=1 reply to google link after incoming call SMS: SZCS#CALL_FUN=1. Reply: SETOK: CALL_FUN=1 |
| 25 | Query the incoming call function | CXCS#CALL_FUN | Reply: READOK: CALL_FUN=1 |
| 26 | Heartbeat packet setting interval | HBT,T1,T2# (T1=60-300s ACC ON, T2=60-300min ACC OFF) | SMS:HBT,180,180# Reply: HBT ACC ON:180s,ACC OFF:180s |
| 27 | Query heartbeat packet interval time | HBT# | Reply:HBT ACC ON:180s,ACC OFF:180s |
| 28 | Set GPS data timing sending interval | TIMER,T1,T2# (T1=5-60s ACC ON, T2=5-1800s ACC OFF) | SMS: TIMER,30,300# Reply: TIMER ACC ON:30s,ACC OFF:300s |
| 29 | Query GPS data timing sending interval time | TIMER# | Reply: TIMER ACC ON:30s,ACC OFF:300s |
| 30 | Turn on vibration alarm settings | SENALM,A,M# (A=ON, M=0-2: 0 GPRS, 1 SMS+GPRS, 2 GPRS+SMS+CALL) | SMS: SENALM,ON,2# Reply: SENALM:ON,2 |
| 31 | Turn off vibration alarm settings | SENALM,OFF# | Reply: SENALM:OFF |
| 32 | Query vibration alarm setting parameters | SENALM# | Reply: SENALM:OFF |
| 33 | Enable power-off alarm settings | POWERALM,A,M,T1,T2,# (A=ON, M=0-2, T1=2-60s, T2=1-3600s) | SMS: POWERALM,ON,2,10,10,# Reply: POWERALM:ON,2,10,10 |
| 34 | Turn off the power-off alarm | POWERALM,OFF# | Reply: POWERALM:OFF |
| 35 | Query power-off alarm status | POWERALM# | Reply: POWERALM:ON,2,10,10 |
| 36 | Enable low battery alarm settings | BATALM,A,M# (A=ON) | SMS: BATALM,ON,1# Reply: BATALM:ON,1 |
| 37 | Turn off low battery alarm settings | BATALM,OFF# | Reply: BATALM:OFF |
| 38 | Query the low battery alarm status | BATALM# | Reply: BATALM:ON,1 |
| 39 | Enable movement alarm settings | MOVING,A,R,M# (A=ON, R=100-1000m, M=0-2) | SMS: MOVING,ON,1000,2# Reply: MOVING:ON,1000,2 |
| 40 | Turn off movement alarm | MOVING,OFF# | Reply: MOVING:OFF |
| 41 | Query the movement setting status | MOVING# | Reply: MOVING:ON,1000,2 |
| 42 | Turn on overspeed alarm | SPEED,A,B,C,M# (A=ON, B=5-600s, C=1-255km/h, M=0-1) | SMS: SPEED,ON,10,120,1# Reply: SPEED:ON,10,120,1 |
| 43 | Turn off over speed alarm | SPEED,OFF# | Reply: SPEED:OFF |
| 44 | Query overspeed setting status | SPEED# | Reply: SPEED:ON,10,120,1 |
| 45 | Turn on ACC ignition on alarm | ACCALM,A,M# (A=ON, M=0-3) | SMS: ACCALM,ON,3# Reply: ACCALM:3,OK |
| 46 | Turn off ACC ignition on alarm | ACCALM,OFF# | Reply: ACCALM,OFF OK |
| 47 | Query ACC ignition on alarm | ACCALM# | Reply: ACCALM:3,OK |
| 48 | Turn on the ACC off alarm | ACCOFFALM,A,M# (A=ON, M=0-3) | SMS: ACCOFFALM,ON,3# Reply: ACCOFFALM:3,OK |
| 49 | Turn off the ACC off alarm | ACCOFFALM,OFF# | Reply: ACCOFFALM,OFF OK |
| 50 | Query ACC off alarm | ACCOFFALM# | Reply: ACCOFFALM:3,OK |
| 51 | Query the sleep working mode | CXCS#SLPDISCONNECT | Reply: READOK: SLPDISCONNECT=0 |
| 52 | SMS time zone settings | GMT,A,B,C# (A: E or W, B: 0-12, C: 0/15/30/45) | A: E or W; "E" means eastern time zone, "W" means western time zone; default: E. B: 0~12; time zone default: 8. C: 0/15/30/45; half time zone; default: 0. SMS: GMT,E,8,0#. Reply: GMT:E,8,0 |
| 53 | SMS time zone query | GMT# | Reply: GMT:E,8,0 |
6. Specifications
The following table details the technical specifications of the EC08 GPS Tracker:
| Content | Specs |
|---|---|
| Dimensions | 80mm x 33mm x 22mm |
| Weight | 50g (Package Weight: 36g) |
| Network | 4G+2G network |
| Band | LTE-FDD B1/B2/B3/B4/B5/B7/B8/B28/B66, GSM 850/900/1800/1900MHz |
| GPS Chip | SIMCOM |
| GSM Module | SIMCOM7670SA |
| GPS Sensitivity | -159dBm |
| GPS Accuracy | 5m (<5 Meters) |
| Time To First Fix | Cold status: 45s, Warm status: 35s, Hot status: 1s |
| Working Voltage | 9V-90V |
| Battery Life | 5 to 9 Hours (Internal Battery) |
| Storage Temperature | -40°C to +85°C |
| Operation Temperature | -20°C to +55°C |
| Working Humidity | 5% ~ 95% |
| GPS Type | GPS Tracker |
| GPS Module | Yes |
| Certification | CE, FCC, RoHS |
| Protocol | GT06 |
| APP | TrackerKing or Your own software |
| Module | Quectel |
7. Warranty and Support
7.1 Warranty Information
The TrackerKing EC08 GPS Tracker comes with a 1-year Supplier Warranty. This warranty covers manufacturing defects and ensures the product functions as described under normal use. Please retain your purchase receipt for warranty claims.
7.2 Customer Support
For further details, technical assistance, or any inquiries regarding your EC08 GPS Tracker, please contact the manufacturer or your supplier. You can also refer to the official web platform www.trackerking.net for additional resources.
A detailed User Manual in PDF format is available for download. You can access it via this link: EC08 User Manual (PDF).
8. User Tips
- Change Default Password: For enhanced security, always change the default login password (123456) immediately after your first successful login to the TrackerKing platform or app.
- Optimal SIM Card Choice: Consult your supplier for recommendations on the best SIM card provider in your region to ensure reliable network coverage and GPRS functionality.
- Regular Monitoring: Periodically check the device's status and location through the app or web platform to ensure it's functioning correctly and providing accurate data.