1. Introduction
Congratulations on your purchase of the VRX RH1066 1/10 Scale RC Electric Big Tire Truck. This high-performance 4WD off-road vehicle is designed for thrilling speeds of 60-70KM/H and features durable metal drive shafts and a reliable Flysky radio system. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your RC truck to ensure a long and enjoyable experience.

Image 1.1: VRX RH1066 RC Electric Big Tire Truck (Yellow/Blue variant)
2. Package Contents
Please check the contents of your package carefully upon receipt. If any items are missing or damaged, contact your retailer immediately.
2.1. Included in the Package:
- 1/10 RC Off-Road Car Model (Pre-assembled and Painted)
- Brushless Motor (3650, 3000KV)
- 45A Brushless ESC (Electronic Speed Controller)
- 3KG Servo
- Remote Controller and Receiver (Flysky Radio System)
- Charger
- Vehicle Battery (7.4V 2S T-Plug)
- Instruction Manual
2.2. Not Included (Required for Operation):
- 4x AAA Batteries for Remote Controller
- Light System (Optional)
- Sound System (Optional)
3. Specifications
Below are the key specifications for your VRX RH1066 RC Truck:
| Feature | Specification |
|---|---|
| Manufacturer | VRX |
| Scale | 1:10 |
| Dimensions (L*W*H) | 440mm * 330mm * 190mm (17.32 * 12.99 * 7.48 inches) |
| Wheelbase | 290mm / 11.4 inches |
| Wheel Diameter | 120mm / 4.7 inches |
| ESC | 45A Brushless |
| Motor | 3650 Brushless Motor 3000KV |
| Servo | 3KG Servo |
| Vehicle Battery | 7.4V 2S T-Plug (Included) |
| Remote Controller Battery | 4x AAA Batteries (Not Included) |
| Speed | 60-70 KM/H |
| Drive System | 4WD with Metal Drive Shafts |
| State of Assembly | Ready-to-Go |
| Material | Plastic |
| Recommended Age | 14+ years |

Image 3.1: RC Car Dimensions (Height: 7.48"/190mm, Width: 12.99"/330mm, Wheelbase: 11.42"/290mm, Length: 17.32"/440mm)
4. Initial Setup
Follow these steps to prepare your RC truck for its first run.
4.1. Charging the Vehicle Battery
- Connect the included charger to a power outlet.
- Connect the vehicle battery (7.4V 2S T-Plug) to the charger.
- Allow the battery to charge fully. Refer to the charger's indicator lights for charging status.
- Important: Never leave charging batteries unattended.
4.2. Installing Remote Controller Batteries
- Open the battery compartment on the back of the remote controller.
- Insert 4x AAA batteries (not included), ensuring correct polarity (+/-).
- Close the battery compartment securely.
4.3. Installing Vehicle Battery
- Carefully remove the body shell of the RC truck.
- Locate the battery compartment or tray on the chassis.
- Place the charged 7.4V 2S T-Plug battery into the compartment.
- Connect the battery's T-Plug connector to the ESC's power input.
- Ensure all wires are neatly tucked away and do not interfere with moving parts.
- Reattach the body shell.

Image 4.1: Chassis layout showing battery placement, ESC, motor, and servo.
4.4. Powering On and Binding
- Turn on the remote controller first.
- Then, turn on the power switch on the RC truck.
- The remote controller and receiver should automatically bind. If not, refer to the detailed instruction manual included in the package for specific binding procedures for the Flysky radio system.
- Test basic controls (steering, throttle) to ensure proper function before driving.

Image 4.2: Front chassis view, highlighting suspension and steering linkages.
5. Operation
The VRX RH1066 is a powerful 4WD off-road truck. Operate it responsibly and in suitable environments.
5.1. Basic Controls
- Throttle Trigger: Pull to accelerate forward, push to brake/reverse.
- Steering Wheel: Turn left to steer left, turn right to steer right.
- Trim Adjustments: Use the trim dials on the remote to fine-tune steering and throttle if the truck doesn't drive straight or stops when the trigger is neutral.
5.2. Driving Tips
- Start with slow speeds to get accustomed to the controls.
- Avoid driving in deep water, mud, or extreme conditions that could damage electronics.
- The 4WD system and big tires provide excellent traction on various terrains, including gravel and dirt.
- Be mindful of the high speed (60-70KM/H) and ensure a clear operating area to prevent accidents.

Image 5.1: RC truck demonstrating off-road capability on gravel.

Image 5.2: RC truck performing on an asphalt surface.
6. Maintenance
Regular maintenance will extend the life and performance of your RC truck.
6.1. After Each Run
- Clean the Truck: Use a soft brush or compressed air to remove dirt, dust, and debris from the chassis, suspension, and motor area. Avoid using water directly on electronics.
- Inspect for Damage: Check for any loose screws, bent parts, or damaged components (e.g., tires, suspension arms, drive shafts).
- Battery Care: Disconnect and remove the vehicle battery. Allow it to cool before recharging. Store batteries in a cool, dry place.
6.2. Periodic Maintenance
- Lubrication: Apply a small amount of RC-safe lubricant to moving parts like drive shafts, universal joints, and suspension pivots.
- Check Screws: Periodically check and tighten all screws, especially those on the chassis, suspension, and motor mount.
- Shock Absorbers: Inspect the shock absorbers for leaks or damage. Ensure they move smoothly.
- Tires: Check tire wear and ensure they are securely mounted to the wheels.

Image 6.1: Detail of the shock absorber and suspension for maintenance reference.
7. Troubleshooting
Here are some common issues and their potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Truck does not respond to remote. | Low battery in remote or vehicle; not bound; power switch off. | Charge vehicle battery; replace remote batteries; ensure both are powered on; re-bind remote and receiver. |
| Truck runs slowly or has low power. | Vehicle battery low; motor/ESC overheating. | Recharge vehicle battery; allow components to cool down before continuing operation. |
| Steering is erratic or not straight. | Steering trim incorrect; damaged servo or linkage. | Adjust steering trim on the remote; inspect servo and steering linkages for damage or looseness. |
| Unusual noises during operation. | Debris in drivetrain; loose gears; worn bearings. | Inspect and clean drivetrain; check gear mesh; replace worn parts. |
8. User Tips
- Always perform a range check before operating your RC truck, especially in new environments.
- Consider purchasing an additional vehicle battery for extended run times.
- When driving at high speeds, be aware of your surroundings and potential obstacles.
- For optimal performance, keep the metal drive shafts clean and lightly lubricated.
9. Warranty and Support
For detailed warranty information, please refer to the specific warranty card or documentation included with your product. If you encounter any issues that cannot be resolved using this manual, or require technical assistance, please contact the seller or manufacturer's customer support directly. Provide your product model (RH1066) and a clear description of the problem for efficient service.
Disclaimer: Not suitable for children under 36 months due to small parts and high-speed operation.