Introduction
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your Bykski A-AS9070TUF-X GPU Water Block. This product is designed to provide efficient liquid cooling for compatible ASUS Radeon RX 9070 series graphics cards, ensuring optimal thermal performance and stability.
Setup and Installation
Before beginning installation, ensure your workspace is clean and static-free. Gather all necessary tools, including a small Phillips head screwdriver, thermal paste, and thermal pads.
Package Contents
Please verify that all components are present in your package:
- 1x Bykski A-AS9070TUF-X GPU Water Block
- Thermal Grease (or pads)
- Gaskets (various sizes)
- M2*5MM Coil Spring Screws
- Backplate
- M2*9.5MM Backplane Screws

Diagram showing the water block assembly and a list of included installation parts.
Installation Steps
- Prepare the Graphics Card:
- Carefully remove the stock cooler from your graphics card.
- Thoroughly clean any residual thermal paste or thermal pads from the GPU die, memory modules, and VRM components using isopropyl alcohol and a lint-free cloth. Ensure all surfaces are clean and dry.

Diagram illustrating the cleaning of the GPU PCB before water block installation.
- Apply Thermal Interface Material:
- Cut the provided thermal pads to the appropriate sizes for the memory modules (VRAM) and voltage regulator modules (VRM/MOSFETs). Carefully place them onto the corresponding components on the GPU PCB.
- Apply a small amount of high-quality thermal paste to the center of the GPU die.

Detailed diagram showing the placement of thermal pads on the MOS and GPU chip areas.
- Install the Water Block:
- Carefully align the water block with the mounting holes on the graphics card. Ensure the GPU die makes proper contact with the copper base of the water block and that all screw holes align.
- Gently place the water block onto the GPU.
- Insert the M2*5MM coil spring screws into the designated holes. Tighten these screws in a diagonal pattern (e.g., top-left, bottom-right, top-right, bottom-left) until snug. Do not overtighten.
- Install the Backplate (if included):
- Align the backplate with the corresponding screw holes on the rear of the graphics card.
- Secure the backplate using the M2*9.5MM backplane screws. Tighten these screws evenly.
- Leak Testing:
- Before powering on your system, it is crucial to perform a leak test. Connect the water block to your custom loop and fill the system with coolant.
- Use an air pressure tester or run the pump for at least 24 hours with the system powered off (using a PSU jumper) to check for any leaks. Place paper towels under all fittings and components to easily spot any drips.
Operating Instructions
Once the water block is installed and the loop is leak-free, you can power on your system. The Bykski GPU Water Block is a passive cooling component; its operation is integrated with your overall liquid cooling system.
- System Startup: Ensure your pump is running and coolant is flowing before booting your computer.
- Temperature Monitoring: Use monitoring software (e.g., GPU-Z, MSI Afterburner) to keep an eye on your GPU temperatures, especially during initial use and under load, to confirm proper cooling performance.
- ARGB Lighting: If your water block features 5V 3PIN ARGB lighting, connect it to a compatible motherboard header or ARGB controller. Use your motherboard's software or the controller to customize lighting effects.
Official product video showcasing the Bykski GPU Water Block's three-layer structure, 9mm thickened design, full coverage water flow, and lightweight construction.
Maintenance
Regular maintenance of your liquid cooling loop is essential for longevity and optimal performance.
- Coolant Replacement: It is recommended to replace your coolant every 6-12 months, depending on the coolant type and system usage.
- System Flush: When replacing coolant, consider flushing your system with distilled water or a dedicated cleaning solution to remove any buildup or debris.
- Block Inspection: Periodically inspect the water block for any signs of corrosion, discoloration, or micro-fin clogging. If significant buildup is observed, the block may need to be disassembled and cleaned with a soft brush and appropriate cleaning solution.
- Fittings Check: Ensure all fittings remain tight and leak-free.
Troubleshooting
Common Issues and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| High GPU Temperatures | Poor thermal paste application, insufficient coolant flow, air bubbles in the block, clogged fins. | Reapply thermal paste, check pump operation, bleed air from the loop, inspect and clean the block. |
| Coolant Leakage | Loose fittings, damaged O-rings, cracked tubing. | Tighten fittings (hand-tight only), replace O-rings, replace damaged tubing. Perform a thorough leak test. |
| ARGB Lighting Not Working | Incorrect connection, faulty ARGB header/controller, software issue. | Check 5V 3PIN connection, test with another ARGB header/controller, update motherboard BIOS/software. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | A-AS9070TUF-X |
| Brand | Bykski |
| Type | VGA Front Water Block |
| Material | Electroplated High Purity Copper / Clear Acrylic |
| Heatsink Material | Copper |
| Screw Thread | G 1/4' |
| RGB Support | A-RGB (5V 3PIN) |
| Thermal Pads | Included |
| Compatibility | ASUS TUF-RX9070-O16G-GAMING, ASUS Radeon RX9070XT TUF O16G GAMING, ASUS Radeon RX9070XT PRIME |
| Certification | CE |
| Origin | Mainland China |
User Tips
- Users report excellent cooling performance, keeping compatible RX 9070 XT cards quiet and cool under load.
- The water block is noted for its high quality and precise fit on compatible ASUS Prime and TUF models.
- While the included paper instructions may be generic (sometimes for CPU blocks), the package typically contains all necessary hardware for installation.
- The product often includes a backplate, which is beneficial for aesthetics and PCB rigidity.
Warranty and Support
For warranty claims, technical support, or further assistance, please contact the official Bykski customer service or your point of purchase. Keep your proof of purchase for warranty validation.
For additional resources and product information, you may visit the official Bykski website.
Note: This manual is for informational purposes. Specifications and contents are subject to change without notice. Always refer to the manufacturer's official website for the most up-to-date information.
