Danfoss 101N0640

Contents

Danfoss 101N0640 Variable Frequency Compressor Driver

User Manual

Model: 101N0640 | Brand: Danfoss

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Danfoss 101N0640 Variable Frequency Compressor Driver. This unit is designed to control 12V/24V DC compressors typically found in car refrigerators and similar mobile cooling applications. Please read this manual thoroughly before attempting to install or operate the device.

2. Safety Information

WARNING: Electrical shock hazard. Always disconnect power before installation or servicing.

  • PRE-FUSE REQUIRED: A suitable fuse must be installed on the positive power supply line to protect the unit and the electrical system from overcurrent. Refer to the compressor manufacturer's specifications for the correct fuse rating.
  • Ensure all wiring connections are secure and correctly polarized (+ to + and - to -).
  • Do not operate the unit if it is damaged or has been exposed to moisture.
  • Installation should be performed by a qualified technician if you are unsure about any steps.
Bottom view of the Danfoss 101N0640 compressor driver showing 'PRE-FUSE REQUIRED' text.
Figure 1: Bottom view of the driver, indicating the requirement for a pre-fuse.

3. Installation and Wiring

The Danfoss 101N0640 driver is designed for integration with a compatible DC compressor and a 12V or 24V DC power source. Follow the steps below for proper installation:

  1. Mounting: Securely mount the compressor driver in a location that is protected from moisture and excessive heat. Ensure adequate ventilation around the unit.
  2. Power Connection: Connect the positive (+) and negative (-) terminals of the driver to your 12V or 24V DC power supply. Remember to install a fuse on the positive line as indicated in the safety section.
  3. Compressor Connection: Connect the three compressor motor windings to the designated C, A, and D terminals on the driver. Ensure these connections are tight.
  4. Fan Connection (Optional): If your system includes a condenser fan, connect it to the 'F' terminal and the negative (-) terminal.
  5. Control Signal Connection: Connect your thermostat or control unit to the 'P' terminal and the negative (-) terminal. This input typically controls the compressor's on/off state or speed. The 'C' terminal (second 'C' from the top) is often used for diagnostic LEDs or communication, refer to your specific compressor documentation for its function.
Front view of the Danfoss 101N0640 compressor driver showing pinout labels: +, -, F, C, A, D, C, P.
Figure 2: Pinout diagram for the Danfoss 101N0640 compressor driver.

3.1 Pinout Description

  • + (Positive): 12/24 Vdc Power Input
  • - (Negative): Ground Connection
  • F (Fan): Output for Condenser Fan (typically 12V or 24V, depending on system voltage)
  • C (Compressor Phase 1): Connection for Compressor Motor Winding
  • A (Compressor Phase 2): Connection for Compressor Motor Winding
  • D (Compressor Phase 3): Connection for Compressor Motor Winding
  • C (Control/Diagnostic): Auxiliary control or diagnostic output (e.g., for LED indicator). Consult compressor documentation.
  • P (Control Input): Thermostat or Speed Control Signal Input

4. Operation

Once properly installed and wired, the Danfoss 101N0640 driver operates automatically based on the control signal received from the connected thermostat or control unit.

  • Power On: Apply 12V or 24V DC power to the driver. The unit will enter a standby mode or begin operation if the control signal demands cooling.
  • Cooling Cycle: When the thermostat calls for cooling, the driver will activate the compressor and, if connected, the condenser fan. The variable frequency technology allows the compressor to operate at different speeds to maintain the desired temperature efficiently.
  • Power Off: Disconnect the main DC power supply to turn off the unit.

5. Maintenance

The Danfoss 101N0640 compressor driver is designed for minimal maintenance. However, regular checks can ensure optimal performance and longevity:

  • Cleaning: Keep the unit clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquid cleaners.
  • Connections: Periodically check all electrical connections to ensure they are tight and free from corrosion.
  • Ventilation: Ensure that the area around the driver remains clear to allow for proper airflow and heat dissipation.

6. Troubleshooting

If you experience issues with your compressor driver, refer to the following common problems and solutions:

Problem Possible Cause Solution
Compressor not starting
  • No power to driver
  • Blown fuse
  • Incorrect wiring
  • Faulty thermostat/control signal
  • Check power supply
  • Inspect and replace fuse if necessary
  • Verify all wiring connections against the diagram
  • Test thermostat/control unit
Compressor runs intermittently
  • Low voltage
  • Overheating
  • Loose connections
  • Check battery voltage and charging system
  • Ensure adequate ventilation around driver and compressor
  • Tighten all electrical connections
Unusual noises from driver
  • Internal fault
  • Loose mounting
  • Disconnect power and contact support
  • Check mounting screws for tightness

If the problem persists after attempting these solutions, please contact customer support.

7. Specifications

Feature Detail
Model 101N0640
Brand Danfoss (Secop)
Type DC/AC Inverter, Variable Frequency Compressor Driver
Input Voltage 12V / 24V DC
Output Type DUAL
Certifications CE, Dot, EAC, TGA, UL
Origin Mainland China
Item Condition New
Package Length 25 cm
Package Width 15 cm
Package Height 10 cm
Package Weight 0.8 kg

8. User Tips

  • For optimal performance, ensure your vehicle's electrical system can provide stable 12V or 24V DC power, especially when the engine is off.
  • Consider using appropriately sized wiring to minimize voltage drop, particularly for longer cable runs.
  • If replacing an existing driver, double-check compatibility with your specific compressor model.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.