PowMr POW-Boost 10A

Contents

PowMr POW-Boost 10A MPPT Solar Charge Controller User Manual

Model: POW-Boost 10A

Brand: PowMr

1. General Information

The PowMr POW-Boost 10A MPPT Solar Charge Controller is designed to efficiently manage power flow from solar panels to batteries. It utilizes advanced Maximum Power Point Tracking (MPPT) technology to maximize energy harvesting from photovoltaic panels, even when the input voltage from the solar panel is lower than the battery voltage. This controller boosts the voltage to meet the battery's charging requirements, ensuring reliable and efficient charging.

It features integrated charge presets and adaptive charge logic suitable for various battery types, including LiFePO4, Gel, and flooded lead-acid. The controller is compatible with 24V, 36V, 48V, 60V, and 72V system voltages. Multiple protection mechanisms are integrated to safeguard both the controller and connected batteries, including protection against overcharge, short circuit, reverse current, over-discharging, reverse polarity, and overload.

An intuitive LCD display provides comprehensive monitoring of charging status and real-time data, allowing users to configure operational programs and optimize energy management. The unit operates silently due to natural convection cooling, eliminating the need for fans or moving parts.

PowMr POW-Boost 10A MPPT Solar Charge Controller front view
Front view of the PowMr POW-Boost 10A MPPT Solar Charge Controller.
Diagram illustrating Advanced MPPT Technology
Advanced MPPT Technology with 99% max efficiency and 98% PV utilization.
Battery compatibility diagram
Compatible with various battery types (GEL, FLD, SLD, LFE, USE, LI) and 24V/36V/48V/60V/72V systems.
Protection features icons
Built-in protection against short circuiting, reverse current, overcharging, over-discharging, reverse polarity, and overload.
Charging stages graph
Battery current and voltage during Bulk, Absorption, and Float charging stages.

2. Important Safety Instructions

WARNING: CAREFULLY READ AND FOLLOW ALL SAFETY INSTRUCTIONS

  • Carefully read this manual before installing or operating the controller. Retain the manual for future reference.
  • The controller must not be installed or operated by individuals lacking appropriate knowledge, experience, or competence, or those with compromised physical, sensory, or mental capabilities, unless under strict instruction and supervision.

2.1 Controller Installation and Operation

  • There are no serviceable parts for this controller. Do NOT disassemble or attempt to repair the controller.
  • Install the controller in a location with good natural airflow/ventilation and sufficient unobstructed space around it.
  • Install the controller on a non-flammable substrate. Ensure no heat-sensitive items are in the immediate vicinity; the controller may become hot during operation.
  • Install the controller in a location protected from environmental conditions such as direct sunlight, water, high moisture, and dust. Keep it away from flammable liquids or gases. The controller is for indoor use only.
  • Do not install or place/operate the controller on top of the battery, directly above the battery, or in a sealed compartment with the battery, as batteries can emit explosive gases.
  • Do not cover or place any other items on top of the controller.

2.2 Battery Installation and Charging

  • Install and charge the battery in a location with good natural airflow/ventilation.
  • Ensure no ignition sources are near the battery, as batteries can emit explosive gases.
  • Battery acid is corrosive; if contact occurs, immediately rinse with water.
  • Do not charge non-rechargeable batteries. Do not charge Li-ion batteries if the battery temperature is below 0°C. Never charge a frozen battery.
  • Ensure the unit is properly set up for the type of battery intended to be charged.

2.3 Battery DC Connections

  • Ensure the DC system is fully shut down/isolated prior to disconnecting existing cabling or making new connections to the battery/DC system.
  • Use flexible multi-stranded copper cable with sufficient cross-sectional area, in line with an appropriate fuse or circuit breaker.
  • NEVER connect the solar panel array to the controller without a battery. The battery must be connected first.

2.4 Controller Setup

  • Refer to the battery manufacturer's instructions and specifications to ensure the battery is suitable for use with this controller and confirm recommended charge settings.
  • The integrated charge modes combined with adaptive charge logic are well suited for most common battery types, such as flooded lead-acid, Gel, and LiFePO4.

3. Product Overview

The PowMr POW-Boost 10A MPPT Solar Charge Controller features an LCD display, function keys for navigation, PV input and battery ports, and a heat sink for efficient cooling.

PowMr MPPT Solar Charge Controller display and buttons
Close-up of the controller's display and buttons.
Multiple views of the PowMr MPPT Solar Charge Controller
Various views of the PowMr MPPT Solar Charge Controller.
Rear view of the PowMr MPPT Solar Charge Controller
Rear view of the PowMr MPPT Solar Charge Controller, showing the heat sink.

3.1 Product Dimensions

Product dimensions of the controller
Dimensions: 140mm (length) x 85mm (width) x 50mm (height). Dimensional measurement tolerance is ±0.5mm.

4. Installation

4.1 Unpacking and Inspection

Before unpacking, check the package for damage. After unpacking, verify that all contents are present and undamaged. The package should contain the controller and a user manual.

4.2 Preparing for Installation

The controller is designed for wall mounting using flanges on its heatsink backplane.

Select the Mount Location:

Consider the following for a suitable and safe location:

  • Install in a location with good natural airflow/ventilation.
  • Ensure sufficient unobstructed space around the controller. A minimum spacing of 150mm is recommended between the top, bottom, and sides.
Installation spacing diagram
Recommended minimum spacing of 150mm around the controller for proper ventilation.
  • Install on a non-flammable substrate. Ensure no heat-sensitive items are nearby, as the controller can get hot during operation.
  • Install in a location protected from direct sunlight, water, high moisture, and dust, and away from flammable liquids or gases. This controller is for indoor use only.
  • Do not install on top of or directly above the battery, or in a sealed compartment with the battery, due to explosive gases.
  • Do not cover the controller or place other items on top of it.

4.3 Installation Steps

  1. Strictly adhere to the requirements and recommendations for location selection.
  2. Inspect the surroundings and spatial environment of the installation location.
  3. Mark the installation holes.
  4. Drill the holes.
  5. Secure the controller using four M5 screws.
Mounting diagram for the controller
Diagram showing how to secure the controller to a wall.

5. Connection

5.1 Things You Need

Ensure you have the following parts for installation and connection:

ItemQuantity
Controller (included)1
DC-cable to connect the positive DC connection (+) of the Pstar Controller to the positive polarity of DC input or DC output2
DC-cable to connect the negative DC connection (-) of the Pstar Controller to the negative polarity of DC input or DC output2
DC breaker2
PV array1
Battery pack1

5.2 Wiring Precautions

  1. All wiring must be carried out by qualified professionals.
  2. Prioritize connecting the battery before connecting the photovoltaic array.
  3. Do not install the controller and lead-acid batteries in an enclosed environment as batteries release explosive gases.
  4. The controller can handle photovoltaic input voltage within the specified range. Exceeding the maximum input voltage can damage the equipment. Inspect the system before making connections.
  5. When configuring wiring and circuit breakers, refer to relevant specifications for maximum current. Choose appropriate cable and circuit breaker sizes. Thicker, shorter cables enhance boost performance and minimize voltage drop.
  6. Install separate DC circuit breakers for each circuit to facilitate safe disconnection during maintenance/repair and provide overcurrent protection.
  7. The controller ports are labeled with polarity markings for PV input and battery charging. Strictly follow these markings when connecting cables.
  8. Keep each circuit breaker in the open position during wiring.
  9. Tighten port screws to avoid loose connections, overheating, and potential fire hazards.
  10. Before closing circuit breakers, check that cable terminals are securely connected and there are no reverse connections or errors.

5.3 Connection Steps

  1. Battery Wiring: Prioritize connecting the battery module. Install a separate DC circuit breaker for the battery charging circuit.
  2. Photovoltaic Wiring: After confirming the configured photovoltaic array voltage is within the acceptable range, connect the photovoltaic array. Install a separate DC circuit breaker on the photovoltaic input line.
  3. Controller Startup: Once the battery and photovoltaic array are connected, check for reverse connections or loose cables. After confirming everything is correct, sequentially close the circuit breakers for the battery charging circuit and photovoltaic input circuit to start the controller.
Wiring diagram for the solar charge controller
Wiring diagram showing connections for PV array, battery, DC breaker, inverter, and AC output.

Video demonstrating the wiring and operation of the PowMr MPPT Solar Charge Controller.

6. Operation

6.1 Operation Interface Introduction

The controller features an LCD display and four function keys: PRG/ESC, Up, Down, and ENTER.

LCD display and function keys diagram
Diagram of the LCD display and function keys.
IconDescription
LCD Display (Left Side)
  1. On the main screen, displays photovoltaic input data and operating mode.
  2. In the settings interface, displays setting options.
  3. In a fault state, displays "ERR".
LCD Display (Right Side)
  1. On the main screen, displays battery charging parameters and device temperature.
  2. In the settings interface, displays setting codes.
  3. In a fault state, displays fault codes (refer to Troubleshooting section).
Battery Charge Status IndicatorIndicates the battery charge status.
PRG/ESC KeyUsed to enter or exit the setup program.
Up Arrow KeyNavigates to the next screen or setting item/increases the setting value.
Down Arrow KeyGoes back to the previous screen or setting item/decreases the setting value.
ENTER KeyIn the setup interface, enters a setting item or confirms the setting value.

6.2 Viewing and Configuration Guide for Parameters

After starting the device, use the Up and Down keys to toggle between different screen information on the main interface.

Browsing Interface Data:

PageLeft Side ParametersRight Side Parameters
1Photovoltaic Input VoltageCurrent Battery Voltage
2Photovoltaic Input PowerCharging Current
3Operating ModeDevice Temperature

Operation Mode:

Mode CodeDescription
3.0Standby state
4.0MPPT State
7.0Content Voltage charging state
8.0Flooded charging state

Configuration Setup Program:

To access the setup program, press the "PRG/ESC" key. Use the Up and Down keys to navigate through options. Press "ENTER" to enter a specific setting. Adjust values with Up and Down keys, then press "ENTER" to confirm.

ItemProgramDescription
D01Open Circuit Voltage of PV InputSets the maximum voltage value the controller will allow from the solar panel, based on the solar panel's maximum open-circuit voltage.
D02Bulk Charging VoltageSpecific to charging lithium batteries. Sets the maximum charging voltage for lithium batteries.
D03Float Charging VoltageSpecific to charging lead-acid batteries. Maintains battery voltage at the float charging voltage with a weak current after full charge.
D04Return-to-MPPT Charging VoltageWhen battery voltage drops to this value, the controller initiates a new charging cycle.
D05Maximum Charging CurrentSets the maximum charging current based on the connected battery's charging parameters.
D06Battery Voltage CalibrationCalibrates the battery voltage measured by the controller if it differs from other devices like a multimeter.

7. Charging Parameter Configuration Reference

Refer to the tables below for appropriate charging parameters based on your battery type.

7.1 For Lead-Acid Battery:

Voltage control parameters24V36V48V60V72V
Boost charging voltage28.8V43.2V57.6V72V86.4V
Sealed Float charging voltage27.6V41.4V55.2V69V82.8V
Boost reconnect charging voltage26.4V39.6V52.8V66V79.2V
Boost charging voltage28.4V42.6V56.8V71V85.2V
GEL Float charging voltage27.6V41.4V55.2V69V82.8V
Boost reconnect charging voltage26.4V39.6V52.8V66V79.2V
Boost charging voltage29.2V43.8V58.4V73V87.6V
FLD Float charging voltage27.6V41.4V55.2V69V82.8V
Boost reconnect charging voltage26.4V39.6V52.8V66V79.2V

7.2 For Lithium Iron Phosphate Battery:

Voltage control parametersBoost charging voltageFloat charging voltageBoost reconnect charging voltage
7S25.2V24.5V22.4V
8S28.8V28V25.6V
11S39.6V38.5V35.2V
12S43.2V42V38.4V
15S54V52.5V48V
16S57.6V56V51.2V
18S64.8V63V57.6V
19S68.4V66.5V60.8V
22S79.2V77V70.4V
23S82.8V80.5V73.6V

7.3 For Ternary Lithium Battery:

Voltage control parametersBoost charging voltageFloat charging voltageBoost reconnect charging voltage
6S25.2V24.6V22.8V
7S29.4V28.7V26.6V
9S37.8V36.9V34.2V
10S42V41V38V
12S50.4V49.2V45.6V
13S54.6V53.3V49.4V
16S67.2V65.6V60.8V
17S71.4V69.7V64.6V
19S79.8V77.9V72.2V
20S84V82V76V

8. Maintenance

Perform inspections and maintenance at least twice a year for optimal performance.

  • Ensure the controller is firmly installed in a clean and dry environment.
  • Ensure no obstructions to airflow around the controller. Clean any dirt or fragments from the heat sink.
  • Check all exposed wires for insulation damage (solarization, frictional wear, dryness, pests). Repair or replace damaged wires if necessary.
  • Tighten all terminals. Inspect for loose, broken, or burnt wire connections.
  • Confirm all system components are properly grounded.
  • Confirm all terminals have no corrosion, insulation damage, high temperature, or discolored signs, and tighten terminal screws.
  • Check for dirt, nesting insects, and corrosion. Clean if present.

WARNING: Risk of electric shock!

  • Ensure all power is turned off before performing inspections or operations.

9. Troubleshooting

The controller display shows error signals to help identify the source of a failure.

Fault CodePossible CauseWhat to do
No. 1Reverse PolarityFully protected; no damage. Correct the miswiring to resume normal operation.
No. 2Maximum Charging Current limitEnsures safe charging current to prevent battery damage and prolong battery life.
No. 3Short Circuit ProtectionThe controller shuts down output for one minute.
No. 4Controller OverheatingWhen temperature exceeds 85°C, charging stops. Resumes when temperature is 75°C.
60Temperature Too HighNormal charging and discharging resume once device temperature cools below recovery temperature.
63High Battery VoltageReconfigure parameters or verify if battery voltage exceeds rated voltage. Consider shutting off the photovoltaic array circuit breaker.
71High PV VoltageReconfigure parameters or lower the voltage by adjusting series and parallel connections.
73Excessive Charging CurrentReduce the number of photovoltaic arrays connected to the controller.

10. Technical Specifications

CategorySpecification
ModelPOW-Boost 10A
PV Input
PV Input Voltage15~25V25~48V48~60V
PV Input Power≤150W≤250W≤400W
System Voltage24/36/48/60/72V48/60/72V60/72V
Charging Mode
Charging technologyMPPT
Charge Algorithm3-Stage
Self-consumption<2W
Nominal System Voltage24V/36V/48V/60V/72V
Battery Voltage Range20~88V
Environment
Operating Temperature Range-35°C~+65°C
Humidity Range≤95%
General Specification
Protection ClassIP32
Dimension140*85*50mm
Net weight305g

11. User Tips

  • Connection Order is Crucial: Always connect the battery to the controller first before connecting the solar panels. This prevents potential damage to the controller.
  • Verify Readings: Some users have reported discrepancies in current sensor readings and voltage calibration. It is advisable to verify the controller's readings with an external multimeter, especially during initial setup, to ensure accurate charging and prevent battery damage. Adjust calibration (D06) if necessary.
  • Optimize PV Input: If you experience lower-than-expected charging wattage, ensure your solar panel voltage and power are within the optimal range for the controller. Adjusting series/parallel connections of PV arrays might be necessary to achieve better performance.
  • Check for Defects: Upon arrival, carefully inspect the device for any manufacturing defects, such as blocked connection sockets, before attempting installation.
  • Consult PDF Manual: For a more detailed guide, including specific diagrams and advanced settings, please refer to the official user manual PDF available at https://manuals.plus/m/70c794a93a20bc017355910dda0acccdeeb89c8f5197ab19d23edfff9eebc531.

12. Warranty and Support

All PowMr products typically come with a 1-year warranty from the store.

For technical support or inquiries, please contact:

  • Email: support@powmr.com
  • Tel/Fax: +86 755-28219903
  • Web: www.powmr.com
  • Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.