SAMOLLA TX800 Electric Count Wheel Fishing Reel

1. Introduction

Thank you for choosing the SAMOLLA TX800 Electric Count Wheel Fishing Reel. This ultralight baitcasting reel is designed for precision and durability, featuring a digital E-Line Counter, high gear ratio, and robust drag system. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting to ensure you get the best performance from your reel.

Figure 1: SAMOLLA TX800 Electric Count Wheel Fishing Reel, highlighting key features like 7+1 Ball Bearing, 7.2:1 Gear Ratio, 10KG Max Drag, and 10 Magnetic Beans.

2. Safety Information

Please read and understand all safety precautions before using your fishing reel. Failure to follow these instructions may result in injury or damage to the product.

• Casting Safety: Always ensure the bail is in the correct position before casting. Incorrect operation can lead to line breakage, unexpected lure trajectory, and potential injury to yourself or others.
• Anti-Reverse Knob: When the anti-reverse knob is set to "ON", the handle should only move forward. If it is set to "OFF", the handle can move backward rapidly, which may cause injury to your hand.
• Moving Parts: Do not touch the fishing line when it rapidly exits the spool, as it may cut your finger. Avoid touching rotating parts like the handle, rotating disc, and spool during operation.
• Damaged Reel: If the reel has peeling on gold-plated or painted surfaces, or sharp edges appear after impact, do not use it as it may cause injury.
• Hooked Lines: If your hooks become accidentally snagged underwater, do not force the fishing rod and reel. Instead, wrap the fishing line with a towel or cloth and slowly pull the hooks out. Forcing it can damage the reel. Do not cut the fishing line with scissors as it can harm the environment.
• Dropping the Reel: Be careful not to drop the fishing reel. If it falls onto hard surfaces like asphalt or cement, especially during installation on a rod, the reel leg may break.
• Water and Sand Exposure: Do not place the fishing reel directly in sand or submerge it in water. Sand or water entering the reel can cause malfunctions.
• Children: Keep the fishing reel out of reach of children to prevent unexpected accidents.
• Drag System: Ensure the drag system is correctly set before casting. Double-check that the drag knob works properly. An improperly set drag can cause injury if an accident occurs.
• Intended Use: Use the fishing reel only for its intended purpose of fishing.
• Lubrication: Be aware that lubricating oil is applied to rotating parts. Handle with care to avoid staining clothing.
• Storage: When storing or moving the reel, pay particular attention not to throw it arbitrarily. Store it separately from other hard items to prevent scratches or breakage.

3. Main Components

Familiarize yourself with the main components of your SAMOLLA TX800 fishing reel:

• Body: The main housing of the reel.
• Handle: Used to retrieve the line.
• Bail: The wire arm that guides the line onto the spool (for spinning reels, though this is a baitcaster, the term might be used generically for line guide).
• Drag Knob: Adjusts the tension on the line to control how easily line can be pulled from the spool.
• Spool: The cylinder around which fishing line is wound.
• Rotor: The rotating part of the reel that holds the bail.
• Line Roller: Guides the line smoothly onto the spool.
• E-Line Counter: Digital display for line length and depth.
• Cast Control Knob: Adjusts casting performance.
• Magnetic Brake System: Provides casting control.
• Ceramic Outlet Hole: Guides the line smoothly during casting and retrieval.
• Star Drag: Fine-tunes drag settings.

Figure 2: Exploded view diagram of a typical fishing reel. Refer to this diagram for identification of internal components.

4. Setup Instructions

4.1. Handle Installation (Left/Right Hand)

The TX800 reel is available in both Left Hand (TX800L) and Right Hand (TX800R) models. Ensure you have the correct model for your preference.

For Screw-in Type Handle:

1. Screw off the handle cap.
2. Move the handle backward and screw it off. (Keep the Anti-reverse knob "ON" if it has one).
3. Screw on the handle in its opposite side and move forward. You can hold the rotor during this process to ensure the handle is installed correctly.
4. Screw on the handle cap.

For Plug-in Type Handle:

1. Screw off the handle cap anticlockwise.
2. Pull the handle out and plug it into the opposite side.
3. Screw on the handle cap.

4.2. Spool Installation and Unloading

Unloading Method: Turn the drag knob counterclockwise until the spool automatically comes off.

Installation Method: Put the spool on the rotor seat and rotate it left and right until it is fixed well. Turn and screw the drag knob clockwise until tight.

4.3. Line Winding

1. Install the fishing reel onto your fishing rod.
2. Adjust the drag knob to a suitable setting.
3. Connect the fishing line directly to the spool through the rod guides. The junction should be fixed by tape or similar means.
4. Erect the spool with the line wound on it, and start reeling the line while maintaining tension.
5. Make a mark at every 1/3 point of the full line capacity. For example, if the line capacity is 150 meters, mark at 50 meters, 100 meters, and 150 meters.

4.4. Reel Installation on Rod

Slide the reel foot into the reel seat on your fishing rod and tighten the reel seat nut securely.

4.5. Adjustment of Line Shape on Spool

The reel allows for adjustment of the line shape on the spool to optimize casting performance. This is typically done using washers under the spool.

• If the line is winding with a concave shape (more line on edges than center), add a washer.
• If the line is winding with a convex shape (more line in center than edges), remove a washer.
• Aim for a flat, even line lay for normal use.

5. Operating Instructions

5.1. Power ON/OFF (E-Line Counter)

Figure 3: E-Line Counter display with ON/OFF and SET buttons.

• To Turn On: Long press the left button.
• To Turn Off: Long press the left button for 2 seconds.
• Automatic Shut-off: The reel will automatically turn off within 30 minutes if no operation is performed while powered on.

5.2. Spool Type Setting (L1/L2)

Figure 4: Spool type selection display (L1 for standard, L2 for deep).

• While powered on, long press the right SET button for 2 seconds to enter the thread cup (spool) setting state.
• Short press the left button to cycle through display options: L1 (standard spool) or L2 (deep spool).
• Long press the right SET button for 2 seconds to automatically save the selected spool type.

5.3. PE Line Number Setting

Figure 5: PE line number setting display.

• While powered on, long press the right SET button for 2 seconds to enter the fish line number setting state. The default display is PE line 1.0.
• Short press the left button to cycle through PE line numbers: 0.8 → 1.0 → 1.2 → 1.5 → 2.0 → 3.0 → 4.0.
• Select your desired line number, then long press the right SET button for 2 seconds to automatically save the selection.

5.4. Wire Wrap Mode / Zeroing Operation

Figure 6: Display during wire wrap mode.

• In wire wrap mode, short press the left button to perform a zeroing operation, which facilitates re-winding.
• During the winding process, the top line of numbers on the screen will display the actual wound wire length.
• After wrapping the line, press and hold the right SET button for 2 seconds to automatically save the length of the wrapped line and switch back to normal working mode.

5.5. Line Collection/Discharge & Clearing Data

Figure 7: Display showing outgoing line distance.

• When casting bait, the screen will display the outgoing line distance.
• To clear the outgoing line length data in normal working condition, double-click the left switch button.

5.6. Alarm Flashing Device (Fish Hook-up Flash Function)

Figure 8: Alarm Flashing Device in action.

• Click the right button to turn on the alarm function. The screen number will flash to indicate it's active.
• When a fish pulls the fishing line, the screen will start flashing and emit an alarm sound.
• The screen will flash for approximately 5 seconds and then automatically recover.
• Press the right button again to turn off the alarm.

5.7. Depth Positioning Function

Figure 9: Depth Positioning Function display.

• Press the left button to activate the depth positioning alarm. The positioning depth will be displayed, and the meter will start flashing.
• This function is useful for recording the water depth where specific fish are found and for ensuring your bait reaches the desired depth.

5.8. Magnetic Brake System Adjustment

Figure 10: Magnetic Brake System with 0-12 adjustment dial and internal magnetic beans.

The TX800 features a new generation micro magnetic brake system with 10 magnetic beans for accurate casting control. Adjust the dial from 0-12 based on your casting needs:

• 0-4 Pin: For super long casting with heavy bait.
• 4-8 Pin: General purpose casting.
• 8-12 Pin: For beginners or light bait.

5.9. Drag System Adjustment

The drag system protects your fishing line when the spool reverses due to a sudden bite from a fish. Adjust the power of the drag using the drag knob.

• Turn the drag knob to the right to reinforce drag power.
• Turn the drag knob to the left to weaken drag power.
• Ensure the drag is set appropriately for the fish you are targeting to prevent line breakage or damage to the reel.

5.10. Long Casting Method

1. Keep the line with your index finger.
2. Ensure the bail is in the correct position.
3. Raise the rod over your head, then cast.

6. Maintenance

Proper maintenance will extend the life of your SAMOLLA TX800 reel and ensure smooth operation. To prevent rust and salt damage, follow these recommendations:

6.1. Cleaning

1. Unload from Rod: Always unload your reel from the fishing rod after use.
2. Wash with Clean Water: Use a shower or sprayer to wash the reel with clean water. This helps remove salt, sand, and other debris.
3. Avoid Hot Water: Do not use hot water, as it can wash out the lubricating oil.
4. Do Not Submerge: Do not submerge the entire reel in water.

6.2. Air Drying

1. After washing, wipe off excess water from the reel.
2. Place the reel in the shade to air dry.
3. Loosen the drag knob and remove any covers on maintenance ports to facilitate quicker drying.
4. Avoid Direct Sunlight/Heat: Do not use a hair dryer or place the reel in direct sunlight, as high temperatures can damage the reel.

6.3. Storage

• Always unload the reel from the rod before storing.
• Store the reel in a dry and shaded place.
• If the reel is stored in a high-humidity or sealed environment (e.g., car trunk) with residual water, it may rust quickly.
• Keep the reel clean and dry for a longer service life.

6.4. USB Charge Port

Figure 11: USB charging port with waterproof plug.

The reel is equipped with a USB charging port for convenient charging. Ensure the waterproof plug is securely in place when not charging to prevent water ingress.

7. Troubleshooting

This section addresses common issues you might encounter with your SAMOLLA TX800 reel.

• Low Voltage Alarm:
  

  Figure 12: Low voltage indicator on the E-Line Counter.

  If the display shows 'LIGHT' with a flashing battery icon, or if the screen figures appear blurred and power is less than 1/4, it indicates a low voltage. Charge or replace the battery promptly.
• Reel Not Powering On: Ensure the battery is charged. Long press the left button for a few seconds to power on.
• Inaccurate Line Counter: Verify that the correct PE line number and spool type (L1/L2) are set in the reel's settings. Perform a zeroing operation if re-winding line.
• Casting Issues: Adjust the magnetic brake system (0-12 Pin) according to bait weight and casting distance desired. Ensure the line is wound evenly on the spool.
• Drag Not Holding: Check the drag knob adjustment. Ensure it is tightened sufficiently for the target fish. Clean the drag washers if they are slipping excessively.

8. Specifications

Figure 13: Parameter table for SAMOLLA TX800.

Figure 14: Dimensions of the SAMOLLA TX800 fishing reel and spool.

9. User Tips

• Line Counter Accuracy: For best accuracy with the E-Line Counter, ensure you correctly set the PE line number and spool type (L1/L2) before fishing.
• Battery Life: Keep an eye on the low voltage alarm. Charging the battery before each trip can prevent interruptions.
• Casting Practice: Experiment with the magnetic brake system settings (0-12 Pin) to find the optimal balance for different bait weights and wind conditions.
• Depth Memory: Utilize the depth positioning function to mark productive depths, especially when targeting specific species or structures.
• Smooth Operation: Regular cleaning and proper storage will maintain the reel's smooth performance and extend its lifespan.

10. Warranty and Support

For any questions, technical support, or warranty inquiries regarding your SAMOLLA TX800 fishing reel, please contact your retailer or the manufacturer directly. Additional information and guides may be available in the official user manual PDF, which can be found at this link.