1. Introduction and Safety Information
1.1. Preface
Thank you for purchasing this product, which is a dual band/dual display/dual watch radio. This easy-to-use radio will deliver secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use. The information presented herein will help you to derive maximum performance from your radio.
1.2. Safety Warnings
WARNING! European Users:
Operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU.
ATTENTION! Programming:
When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. You can use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.
ATTENTION! RF Energy Exposure:
Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.
Illegal Frequencies:
You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.
1.3. Precautions for Portable Terminals
Operating Prohibitions
To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips
To help you make better use of the product, be sure to observe the following instructions:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
1.4. Precautions for Batteries
Charging Prohibitions
To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charge.
- Do not charge your battery suffering deformation, leakage and overheat.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge shall always be prohibited for it may shorten the life of your battery.
2. Package Contents
The UV-5R Mini package typically includes the following items. Charger and power adapter are subject to the final configuration of the dealer.
| Item | Quantity (PCS) | Item | Quantity (PCS) |
|---|---|---|---|
| Radio | 1 | Lanyard | 1 |
| Battery | 1 | Operation Manual | 1 |
| Antenna | 1 | Belt Clip | 1 |
Please understand that the charging instructions in this manual may not be appropriate if Type-C charging method is used with a different adapter.

3. Product Overview

3.1. Key Function Display
- PTT-A Button
- PTT-B Button
- SK1-Customized Function Keys/Monitor Button
- Antenna
- Flashlight
- Volume/Power Knob
- Screen
- Microphone
- Search/Flashlight Button
- V/M-VFO/MR
- A/B
- Up Button/Down Button
- OK/Menu Button
- Cance/Back Button
- Numeric Keypad
- Accessory Port
- Battery Latch
- Type-C Charging Port
- Type-C Charging Indicator Light
4. Basic Operations
4.1. Turning Your Radio On and Off
- To turn your radio ON, turn the [Volume/Power] rotary knob clockwise.
- To turn your radio OFF, turn the [Volume/Power] rotary knob counterclockwise.
4.2. Setting the Volume
- Increase volume by turning the [Volume/Power] rotary knob clockwise.
- To decrease volume, turn the [Volume/Power] rotary knob counterclockwise.
- Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.
4.3. Locking or Unlocking Keypad
To avoid accidentally changing radio settings:
- Press and hold the [*] key to lock the keypad until the screen displays the "" icon.
- In lock mode, you can turn the intercom on and off, adjust the volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
- In lock mode, press and hold the [*] key to unlock the keypad until the "" icon is no longer displayed to unlock the radio.
5. Advanced Operations
5.1. Keypad Entry
You can enter radio aliases, channel aliases, numbers, etc. using the radio's numeric keypad.
- To switch between input methods, press [# ↑ ] key.
- Press 1 to enter a special character (except in numeric input mode, where the number 1 is entered).
- Press 0 to enter a space (except in the numeric input mode, in which special characters are entered).
5.2. Select a Channel
The channel is the channel through which the signal is transmitted. Press the [V/M] button to toggle between VFO and channel mode to select channel mode.
- Press the ▲/▼ buttons or the rotary encoder to select the desired channel.
- Enter the channel number using the keypad. For example, to switch to channel 64, enter 064 totaling 3 digits to switch to channel 64.
5.3. Channel Memory
In Frequency and in Standby mode, you can store frequencies and parameters.
- Press [MENU] [3] [MENU] [1] [5], the screen will display “MEMCH”.
- Press [MENU] to enter the function. Press the ▲/▼ buttons to select the channel, then press [MENU] to store it. A sound tone will confirm that the storing succeeded. Press [EXIT] to exit to return to standby mode.
NOTE:
If you want to set CTCSS tones, DCS codes or the frequency offset, you have to do it before storing the channel. Stored channels are displayed as CH-, other channels have no CH- display.
5.4. Delete a Channel (DEL-CH)
VFO mode and in standby mode, press [MENU] [3] [MENU] [1] [6], the screen will display “DELCH”.
- Press [MENU] to enter the function. Press the ▲/▼ buttons or rotate the encoder to select the channel you want to delete, then press [MENU] to confirm.
- To return to the standby mode press [EXIT] key.
NOTE: Channel 1 cannot be deleted.
5.5. Main Band/Sub Band Switch
In standby mode, press the [A/B] key to toggle between the A and B bands to switch between the main/sub bands. The main band is the highlighted band. The darker displayed band is the sub-band.
5.6. VFO/Channel Switch
- Press the [V/M] button to switch between VFO and channel display.
- VFO mode will display the ‘VFO' icon. MR mode will display the channel serial number.
5.7. Setting the VFO Frequency
- Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.
- Operation 1: Input the VFO frequency directly with the keypad.
- Operation 2: Press the ▲/▼ button or rotary encoder to adjust the VFO frequency in the set frequency step.
5.8. Call Service
All radios in the group must be set to the same channel and sub-code to communicate.
To ensure optimal reception volume, keep the distance between the microphone and your mouth at 2.5 cm to 5 cm when transmitting.
- Initiate a call: Select a channel, press and hold the [PTT-A] key, the radio transmits on segment A (upper screen) and the red indicator light is always on. Then speak into the microphone with normal voice tone. Press and hold the [PTT-B] key, the radio transmits on the B segment (lower screen), and the red indicator light is always on. Then speak into the microphone in a normal voice tone.
- Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light is always on.
5.9. Emergency Alarm
Emergency alarm means that the terminal can initiate an emergency alarm to seek help from the companion or the control center when it encounters an emergency.
- In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.
5.10. Flashlight
- In standby mode, press the preset " key to turn the flashlight on or off.
5.11. FM Radio Function
Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1.
Turn on the radio and press the SK1 key [FM Radio] to enter radio mode and the screen displays the tuning frequency. The following operations can be performed:
- Press ▲/▼ key to search for radio channels at the preset step frequency.
- Press the [# ↑ ] key to search for radio channels automatically, the screen displays 'SEEK...'
- Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
- Press SK1 key [FM Radio] to exit radio mode.
5.12. Monitor
Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. You can also listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. Release the [Monitor] key to exit the monitor mode.
5.13. Frequency Search
Press the pre-programmed [SEARCH] key or press and hold " key, the radio enters into frequency search state, the screen displays "SEARCH...". Press [# ↑ ] key to switch the searching band, such as VHF/UHF, etc. The frequency and CTCSS/DCS code will be displayed after searching is completed. Press [MENU] to save the channel.
5.14. Reverse Frequency Function
Short press the [*] key in relay mode can invert the receive frequency and transmit frequency, the screen shows 'R' icon. This function is often used in repeater channels, and is effective when there is a frequency difference between the receive frequency and the transmit frequency.
5.15. Talk Around Function
In repeater mode, press [*] to switch between Talkaround Mode and Repeater Mode, the screen displays between ‘T' icon and 'R' icon. In Talkaround mode, the receive frequency is equal to the transmit frequency.
5.16. Repeater Activation Tone
Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.
5.17. Voice-activated transmit (VOX)
Enable VOX function, you don't need to press PTT key to transmit, through the voice of normal speech automatically transmit, after the speech stops, it will stop transmitting automatically and wait for receiving. VOX function is enabled:
- Standby status, press [MENU][2][MENU][4] to enter Vox Switch;
- Press [MENU][2][MENU][5] to enter Vox Level, press ▲/▼ to select VOX level (level 1-9);
- Open VOX, select VOX level 1 level-9, the smaller the value, the higher the sensitivity, the 'V' icon is displayed at the top of the screen. Default is off.
- Turn off VOX, select OFF OFF, V icon disappears.
- Press [MENU] key to save the setting and return to the upper menu.
- Repeat the above operation and select OFF to turn off the VOX function.
5.18. Dual Watch
When in Dual watch mode, the radio can receive the frequency set for channel A or B. Operation is as follows:
- Press [MENU] [2] to enter Radio Set.
- Press [MENU] + ▲/▼ to select "15 Dual Watch".
- Press [MENU] key to enter Dual Watch Setting, press ▲/▼ key to select “On”.
- Press [MENU] key to save and return to the upper menu. The dual watch function will be turned on, and the icon 'D' will be displayed on the first line of the screen.
- Repeat the above operation and select "Off”, the Dual Watch function is turned off and the icon 'D' disappears from the first line of the screen. The sub-band displays the " icon.
5.19. Stopwatch Function
Press and hold the [MENU] key to enable the stopwatch function. The stopwatch timing operates as follows:
- Press the [MENU] key to start the stopwatch.
- Press the [MENU] key again to stop the stopwatch.
- Press the [EXIT] key to exit the stopwatch function.
5.20. Weather Radio/Scan Weather Channel
Your radio has a NOAA Weather Radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA Weather Scan function, to enable the user to scan all 10 channels of the NOAA Weather Radio.
- To turn the NOAA Weather Scan on, press and hold the [0] key for 3 seconds, " icon appears. The radio will go to Weather band mode.
- Press and hold the [# ↑ ] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the [# ↑ ] key for 3 seconds during a NOAA weather scan will stop the scan.
- After stopping NOAA weather scan, it is allowed to manually select the weather channel by press the ▲ or ▼ key.
- To exit the Weather Radio broadcast mode, press the " key or [PTT] key.
Weather Channel Frequencies and Names
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| CH-01 | 162.550 | CH-06 | 162.500 |
| CH-02 | 162.400 | CH-07 | 162.525 |
| CH-03 | 162.475 | CH-08 | 161.650 |
| CH-04 | 162.425 | CH-09 | 161.775 |
| CH-05 | 162.450 | CH-10 | 163.275 |
NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
7. Wireless Programming
You can program the radio wirelessly. Before programming the radio wirelessly, you need to install the APP program. Download at scan:

7.1. Wireless Program Radio Operation
The radio operates as follows:
- Press [MENU] + [4] to enter Wireless CPS.
- Press [MENU] + ▲/▼ to select "On"; The " icon will be displayed on the first line of the screen.
7.2. Download Radio APP
You can program the terminal through the radio APP. Download and install radio APP on your Android phone. After the APP is opened, allow the Bluetooth of the cell phone and open the location function, select the walkie-talkie model 5Rmini Series, connect the radio, click Walkie-talkie. prompt the connection success and return to the home page.
7.3. Programming Functions
- Read the radio data: After finishing the frequency reading, click the program to enter the program details. In the program details interface you can program channel information, frequency mode, optional functions.
- Save Profile: The programmed profile allows you to save the profile as a new profile and name the new profile. If you select Replace Program, click Replace Program and save.
- Write data to radio: click home page, select program, click 'Write' to enter write frequency, the radio will restart automatically when finish writing frequency.
8. Technical Specifications
8.1. General Specifications
| Attribute | Value |
|---|---|
| Receiver Frequency | FM 76-108 MHz; VHF 136-174MHz, UHF 400-520MHz, 350-390MHz |
| Transmission Frequency | VHF 144-148MHz, UHF 420-450MHz |
| Channel Spacing | 25.0KHz(Wide)/12.5KHz(Narr) |
| Memory Channel | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Dimensions | 108mm×52mm×37mm (No antenna) |
| Weight | 200g (Battery pack included) |
| Transmission current | ≤1600mA |
| Receive Sensitivity | 0.25μV (12dB SINAD) |
| Rated Audio Power Output | 1W @16 ohms |
| Receive current | ≤380mA |
| Connection for accessories | 2 pin Kenwood jack |
| Antenna impedance | 50 Ohm |
| Output Power(w) | 5w-10w |
| Battery Capacity(mAh) | 1600mAh |
| Waterproof / Water-Resistant | IP45 |
| Battery Included | Yes |
| Material | Plastic |
| Is_Display | Yes |
| Maximum Range | 3km-5km |
| Certification | CE,Dot,EAC,EPA,FCC,GMP,RoHS,TGA,UL,KC,pse,weee |
NOTE: All specifications may be modified without prior notice or liability. Thank you.
9. Maintenance
9.1. General Maintenance
Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years.
- Do not attempt to open the radio for any reason! The radio's precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
- Do not store the Radio under the sunshine or in hot areas.
- High temperatures can shorten the life of electronic devices, and warp or melt certain plastics.
- Do not store the radio in dusty and dirty areas.
- Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
- If it appears that the Radio diffuses peculiar smell or smoke, please shut off its power immediately and take off the charger or battery from the radio.
- Do not transmit without antenna.
9.2. Battery Maintenance Instructions
To help your battery work normally or prolong its life, be sure to observe the following instructions:
- Accumulated dust on charging connector may affect normal charging. Please use a clean and dry cloth to wipe it on a regular basis.
- It is recommended to charge the battery under 5°C~40°C. Violation of the said limit may cause battery life reduction or even battery leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.
- Do not squeeze and penetrate the battery, nor remove its housing.
10. Troubleshooting
This section provides solutions to common issues you might encounter with your UV-5R Mini radio.
- No Power: Ensure the battery is fully charged and properly installed. Check the volume/power knob is turned clockwise to the ON position.
- Cannot Transmit/Receive: Verify the radio is on the correct channel and frequency. Check if the antenna is securely attached. Ensure the PTT button is pressed correctly. If using VOX, ensure it's configured correctly.
- Poor Audio Quality: Check antenna connection. Ensure you are within range of other radios. Adjust squelch level if receiving weak signals.
- Keypad Locked: If the keypad is unresponsive, press and hold the [*] key to unlock it.
- Radio Not Charging: Ensure the Type-C cable and charger are properly connected. Check the charging indicator light. If the battery is wet or damaged, do not attempt to charge it.
- Interference: Move away from other electronic devices or sources of strong RF signals.
11. User Tips
- Efficient Programming: Utilize the Bluetooth APP programming feature for quick and easy frequency management and channel editing directly from your smartphone. This simplifies the traditional programming process.
- Quick Frequency Copy: Use the one-touch copy frequency function to quickly align your radio with another, making group communication setup effortless without complex manual settings.
- Battery Life Extension: To maximize battery life, consider enabling the 'Power Save' function in the menu. Also, ensure charging is done within the recommended temperature range (5°C~40°C).
- Optimal Communication: For clear transmissions, hold the microphone 2.5 cm to 5 cm from your mouth. Experiment with the High/Low power settings to balance range and battery consumption.
- Flashlight Use: The built-in flashlight is a handy feature for dark environments. Remember it can be quickly toggled on/off from standby mode using the preset button.
12. Warranty and Support
12.1. Warranty Information
We promise to carefully 100% INSPECT quality, specification and quantity of the items before delivery.
- We offer ONE YEAR WARRANTY for radio body.
- THREE MONTHS for battery, charger and other accessories.
12.2. Item Guides & Documents
A PDF version of the user manual is available for download: User manual (PDF)
13. Regulatory Compliance
13.1. EU Regulatory Conformance
As certified by the qualified laboratory, the product is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC (2014/53/EU). All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, 2012/19/EU). Please note that the above information is applicable to EU countries only.
13.2. FCC Part 15/IC Compliance
FCC Part 15 Compliance
This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Avis de conformité à la FCC : Ce dispositif a été testé et s'avère conforme à l'article 15 des règlements de la Commission fédérale des communications (FCC). Ce dispositif est soumis aux conditions suivantes: 1) Ce dispositif ne doit pas causer d'interférences nuisibles et; 2) Il doit pouvoir supporter les parasites qu'il reçoit, incluant les parasites pouvant nuire à son fonctionnement.
Tout changement ou modification non approuvé expressément par la partie responsable pourrait annuler le droit à l'utilisateur de faire fonctionner cet équipement.
IC Compliance
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Cet appareil est conforme aux normes RSS exemptes de licences d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférences nuisibles et (2), il doit pouvoir accepter les interférences, incluant celles pouvant nuire à son fonctionnement normal.
Tout changement ou modification non approuvé expressément par la partie responsable pourrait annuler le droit à l'utilisateur de faire fonctionner cet équipement.
13.3. FCC RF Exposure
WARNING! It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the following:
- Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result.
- Please contact your local dealer for a replacement antenna.
Hand-Held Operation (Held-to-Face)
This device was evaluated for typical hand-held (held-to-face) operations with a 1 inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face in order to comply with FCC RF exposure requirements.
Body-Worn Operation
This device was evaluated for body-worn operations with the supplied belt-clip accessory. (All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.
For body worn operation, this device has been tested and meets the Industry Canada RF exposure guidelines when used with our company accessories supplied or designated for this product. Use of other accessories may not ensure compliance with Industry Canada RF exposure guidelines.
Fonctionnement de l'appareil, lorsque porté sur le corps. Cet appareil a été testé et s'est avéré conforme aux normes d'Industrie Canada et approuvé pour le port sur le corps à l'aide des accessoires notre société inclus et conçus pour cet appareil. L'utilisation d'accessoires ne respectant pas les exigences d'exposition RF d'Industrie Canada doit être évitée.
