SONGGER PT-506

Contents

SONGGER PT-506 Pressure Sensor Transducer

Instruction Manual

1. Introduction

The SONGGER PT-506 Pressure Sensor Transducer is a high-accuracy industrial device designed for reliable pressure monitoring in various applications. It provides a standard 4-20mA output signal and operates on a 24VDC power supply. This manual provides essential information for the proper installation, operation, and maintenance of your PT-506 sensor.

PT-506 Pressure Sensor with key specifications
Figure 1: PT-506 Pressure Sensor with key specifications including model, pressure range, signal, voltage, thread, cable length, and operating temperature.

2. Specifications

The PT-506 Pressure Sensor Transducer offers robust performance and precise measurements. Below are the detailed technical specifications:

ParameterSpecification
Pressure Range0–1.0MPa / 0–1.6MPa / 0–2.5MPa (equivalent to 0-10 bar / 0-16 bar / 0-25 bar)
Output Signal4–20mA
Thread ConnectionG1/4 (default), G1/2, M20×1.5 (customizable)
Power Supply24VDC (10–36VDC)
Overload Pressure200%FS
Accuracy±0.5%FS
Operating Temperature–40 to +85℃
Temperature Drift±0.03%FS/°C
Waterproof RatingIP67
Electrical ConnectionLead wire
Display Unitbar
MaterialStainless Steel
Table of PT-506 Pressure Sensor specifications
Figure 2: Detailed parameter and specification table for the PT-506 sensor.

3. Key Features

  • High Accuracy Pressure Sensing: Delivers ±0.5%FS precision for reliable monitoring.
  • Waterproof & Dustproof (IP67): Equipped with O-ring seal and built-in gasket for moisture resistance, ensuring durability in harsh environments.
  • Anti-mistake Plug Design: Features a foolproof slot to prevent reverse insertion and potential sensor damage during connection.
  • Enhanced Signal Transmission: Uses 22AWG tinned shielded wire for anti-interference and signal integrity, crucial for stable readings.
  • Multiple Cable Lengths Available: Standard 2m cable; 5m and 10m options are available for different installation needs.
  • Flexible Thread Options: G1/4 (13mm) is standard; G1/2 (20mm) and M20×1.5 are available upon request for broader compatibility.

4. Setup and Installation

Proper installation is crucial for the accurate and reliable operation of the PT-506 pressure sensor. Follow these guidelines:

4.1. Choosing the Sensor Model and Cable Length

The PT-506 is available in an elbow type (default) and a straight type. Standard cable length is 2 meters, with 5m and 10m options available for longer distances.

PT-506 sensor with coiled cable showing 2m, 5m, and 10m cable length options
Figure 3: PT-506 sensor illustrating available cable length options: 2m (standard), 5m, and 10m.

4.2. Thread Connection

The default thread size is G1/4 (Ø13mm). G1/2 (Ø20mm) and M20×1.5 threads are available for specific applications. Ensure the chosen thread matches your system's port.

Three PT-506 elbow model sensors
Figure 4: Multiple PT-506 sensors in the elbow configuration, demonstrating the standard form factor.

4.3. Electrical Connection (Wiring)

The sensor requires a 24VDC power supply and provides a 4-20mA output signal. The lead wire connection consists of two wires:

  • Red Wire: Connect to the 24VDC input terminal (positive).
  • Black Wire: Connect to the signal output terminal.

Ensure correct polarity to prevent damage to the sensor or connected equipment. The anti-mistake plug design helps prevent incorrect insertion.

Wiring diagram for PT-506 pressure sensor
Figure 5: Wiring diagram showing the two-wire aviation lead connection: Red for 24V input, Black for signal output. The sensor is made of all 304 stainless steel with a 13mm thread diameter.

5. Operation

Once installed and wired correctly, the PT-506 sensor will continuously measure pressure and output a corresponding 4-20mA current signal. This signal can be read by a PLC, data logger, or other industrial control systems.

  • 4mA: Represents the minimum pressure in the configured range (e.g., 0 MPa).
  • 20mA: Represents the maximum pressure in the configured range (e.g., 1.0 MPa, 1.6 MPa, or 2.5 MPa).

Ensure your receiving device is calibrated to interpret the 4-20mA signal correctly based on the sensor's pressure range.

6. Maintenance

The PT-506 pressure sensor is designed for low maintenance. However, regular checks can ensure its longevity and accuracy:

  • Periodic Inspection: Visually inspect the sensor and cable for any signs of physical damage, corrosion, or wear.
  • Connection Integrity: Ensure all electrical and threaded connections remain secure.
  • Cleaning: If installed in a dusty or dirty environment, gently clean the sensor body with a soft, damp cloth. Avoid using harsh chemicals.
  • Media Compatibility: Ensure the sensor is only exposed to non-corrosive media as specified (water, air, machine oil).

7. Troubleshooting

Here are some common issues and their potential solutions:

  • No Output/Incorrect Reading:
    • Check power supply (24VDC) and ensure it's within the 10-36VDC range.
    • Verify wiring connections (Red to positive, Black to signal output).
    • Ensure the sensor's pressure range matches the expected pressure in the system.
    • Check for physical damage to the sensor or cable.
  • Sensor Not Fitting Thread:
    • Confirm the thread size of your system (G1/4, G1/2, M20×1.5). The default sensor is G1/4. Contact support if a different thread is required.
  • Incompatible Media:
    • The sensor is designed for non-corrosive media such as water, air, and machine oil. Using it with corrosive substances may lead to damage and inaccurate readings.

8. User Tips

  • Customization: If your application requires a specific thread size (e.g., G1/2, M20×1.5) or a longer cable (5m or 10m), these options are available. Please specify your requirements when ordering or contact customer support for assistance.
  • Media Compatibility: Always ensure the media being measured is non-corrosive to stainless steel, such as water, air, or common machine oils, to prevent sensor damage and ensure accurate readings.

9. Applications

The PT-506 Pressure Sensor Transducer is versatile and suitable for a wide range of industrial and commercial applications, including:

  • Industrial automation systems
  • Hydraulic systems
  • Air compressors
  • Water pumps and water treatment
  • Liquid level monitoring
  • Oil pressure monitoring
PT-506 sensor held in hand
Figure 6: PT-506 sensor, demonstrating its compact size and robust construction.

10. Warranty and Support

For technical consultations, bulk orders, or any support inquiries, please contact us directly:

  • WhatsApp: +86-13311678550
  • Email: miazhao008@gmali.com
Contact information for support
Figure 7: Contact details for technical support and inquiries.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.