1. Introduction
The JDiag M100 Pro Moto Scanner is a new generation handheld motorcycle diagnostic tool designed to assist technicians in diagnosing problems and performing repairs faster. It covers diagnostic functions for virtually all major motorcycle manufacturers. This tool allows for factory service procedures such as resetting service lights, unlocking immobilizers, configuring alarms, making injection adjustments (CO Trimmer), adjusting throttle valve position sensors (TPS), resetting auto-adaptive parameters, and making idling adjustments.
The M100 Pro displays live data, ECU data, reads stored faults (history), and live data parameters like RPM, battery voltage, and throttle angle.
Video: JDiag M100 Pro Product Demonstration. This video showcases the device's interface, navigation, and various diagnostic functions in action.
2. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the scan tool, read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the tool while driving a vehicle. This can cause driver distraction and could lead to a fatal accident.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area. Exhaust gases are poisonous.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
- Put the transmission in P (for A/T) or N (M/T) and ensure the parking brake is engaged.
- Do not connect or disconnect any test equipment while the ignition is ON or the engine is running.
- Keep the tool dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the scan tool when necessary.
3. Package Contents
The JDiag M100 Pro comes with various cables and accessories to support a wide range of motorcycles. Depending on the version (Standard or OBD), the contents may vary.
Standard Version (23 Cables)

Image: JDiag M100 Pro Standard Version. This image displays the main unit, carrying case, and a comprehensive set of 23 diagnostic cables for various motorcycle brands.
- M100 Pro Main Unit
- Main Test Cable (01)
- OBD-16P Cable (02)
- Generation/IV-6P (03)
- APRILIA-3P/HONDA-4P (04-05)
- SUZUKI-4P (06)
- SUZUKI-4P (07)
- SUZUKI-6P (08)
- SYM-3P (09)
- KYMCO-3P (10)
- PGO-6P (11)
- AEON/BENELLI-6P (12)
- KAWASAKI-8P (13)
- YAMAHA-3P/4P (14)
- USB Cable (15)
- Power Clamp/Battery Test (16-17)
- Universal Line
OBD Version (5 Cables)

Image: JDiag M100 Pro OBD Version. This image shows the main unit, carrying case, and the 5 essential cables for OBD diagnostics.
- M100 Pro Main Unit
- USB Cable (15)
- OBD-16P Cable (02)
- Power Clamp/Battery Test (16-17)
- Multiline
- Main Test Cable (01)
4. Setup and Initial Use
4.1 Tool Description
- Probe Tip: Connects to the circuit or component to be tested.
- Head Lights: Illuminates dark work areas.
- Red/Green Polarity Indicator: Identifies positive (Red), negative (Green), or open circuits.
- LCD Display: Shows test results.
- Power Switch: Conducts positive or negative battery current to the tip for activating and testing components.
- Mode Button: Selects work mode (AC voltage, DC voltage, Resistance, Tone).
- Speaker: Emits audio tones (beeps).
- Auxiliary Ground Lead: Assists as a ground lead.
- Adapter: Connects to the battery.
4.2 Powering the Tool
The M100 Pro is powered via the vehicle's battery. Connect the RED battery clamp to the positive terminal of the vehicle's battery, and the BLACK clamp to the negative terminal. When first connected, the tool will sound a beep, and the headlights will turn on to illuminate the probe tip's test area.
4.3 Quick Self-Test
Before testing any circuit or component, perform a quick self-test to ensure the tool is in good working order:
- With the tool connected to the battery, press the power switch forward (positive marking). The Red LED should light, and the LCD will display battery voltage. If the tone feature is on, a high-pitched tone will sound. Release the switch to turn off the LED and tone.
- Press the power switch rearward (negative marking). The Green LED should light, and the LCD will display '0.0V' (ground). If the tone feature is on, a low-pitched tone will sound. Release the switch to turn off the LED and tone.
If these steps are successful, your tool is working correctly.
IMPORTANT:
- When powering up components, you can increase the life of the power switch by first pressing the switch, then contacting the tip to the component. This ensures arcing occurs at the tip, not the switch contacts.
- The tool has automatic short circuit protection. Its internal overload protection system will automatically break the circuit and restart it if an overload or short circuit occurs. A restart screen will appear without damaging the unit.
4.4 Language Selection
The M100 Pro supports multiple languages. Navigate to the 'Setup' menu to select your preferred language. Supported languages include English, Chinese, Thai, Indonesian, Vietnamese, Spanish, Turkish, French, and Cambodian.

Image: JDiag M100 Pro Multi-Language Support. This image shows the device displaying the language selection menu with flags representing supported languages.
5. Operating the Diagnostic Tool
The M100 Pro offers various diagnostic functions and work modes. You can cycle through the work modes by pressing the Mode button.
5.1 Main Diagnostic Functions

Image: JDiag M100 Pro Motor Diagnosis Functions. This image lists the core diagnostic capabilities of the device.
- Read System Information
- Read Data Stream
- Read Fault Code
- Erase Fault Code
- Freeze Data
- Battery Life Detection
- Actuators Test
- CO Idle Speed Adjustment
- Troubleshooting Guidance
- ABS System Test
5.2 Work Modes
There are four modes to diagnose electrical systems, accessed by depressing the Mode button:
- DC Voltage: Contact the probe tip to a circuit; the LCD will display the DC voltage with a resolution of 0.1 volt.
- AC Voltage: Contact the probe tip to a circuit; the LCD will display Max. voltage, Min. voltage, Frequency, and Duty Cycle.
- Resistance: Contact the probe tip to a circuit; the LCD will display the resistance between the tip and the auxiliary ground lead.
- Tone On/Off: Quickly press the Mode button to toggle the audio tone on or off. A short high beep indicates tone ON, a short low beep indicates tone OFF.
5.3 Battery Test Modes
The M100 Pro includes multiple battery test modes for professional testing of motorcycle batteries.

Image: JDiag M100 Pro Multiple Battery Test Modes. This image highlights the various battery testing options available on the device.
- Quick Test
- Standard Test
- Start Test
- Charge Test
- Wave Test
5.4 Test Applications
- Voltage & Polarity Testing: In DC voltage mode, contact the probe tip to a circuit. Red LED/high tone for positive, Green LED/low tone for negative. No LED/tone for open circuits.
- Continuity Testing: In Resistance mode, use the probe tip with chassis ground or the auxiliary ground lead to test continuity on wires and components.
- Signal Circuit Testing: For sensor circuits (e.g., MAP sensor), use AC voltage mode with chassis ground. Observe LCD readings (should be a sine wave) while applying/releasing vacuum.
- Activating Components: In DC voltage mode, connect the auxiliary ground lead to the component's negative terminal. Contact the probe tip to the positive terminal. Quickly press and release the power switch to activate.
- Testing Trailer Lights: In DC voltage mode, clip the auxiliary ground lead to the trailer ground. Probe contacts at the jack and apply voltage to the probe tip to check function and orientation.
- Checking for Bad Ground Contacts: Probe the suspected ground wire. If the Green LED lights then goes out when the power switch is pressed, it's not a true ground. If the circuit breaker trips, it's likely a good ground.
- Following & Locating Short Circuits: Remove the blown fuse. Use the probe tip to energize each fuse contact. The contact that trips the circuit breaker is the shorted circuit. Follow the wire along the harness.
6. Maintenance
- Keep the tool dry, clean, and free from oil, water, or grease.
- Use a mild detergent on a clean cloth to clean the outside of the scan tool when necessary.
- Store the device in its carrying case in a cool, dry place when not in use.
- Ensure all cables are properly coiled and stored to prevent damage.
7. Troubleshooting
- Tool Not Powering On: Ensure battery clamps are securely connected to the correct terminals (Red to positive, Black to negative) and the vehicle battery has sufficient charge.
- Circuit Breaker Trips Frequently: This indicates an overload or short circuit. Check the component or circuit you are testing for faults. The circuit breaker will reset after approximately 15 seconds.
- Inaccurate Readings: Ensure all connections are clean and secure. Check the tool's self-test function to confirm proper operation.
- Display Issues: If the LCD is not clear or responsive, try restarting the device by disconnecting and reconnecting power.
8. Specifications
| Parameter | Value |
|---|---|
| Power | DC10-15V |
| Operating Current | 250mA |
| Storage Temperature | -10°C to 85°C (14°F to 185°F) |
| Operating Temperature | 0°C to 70°C (32°F to 158°F) |
| Humidity | <90% |
| Display | 3.5-inch TFT Color Display (160*128 dpi) |
| Upgrade Ports | USB port |
| Communication Ports | COM port |
| DC Voltage Range | 0-65V ±1 digit |
| Resistance Range | 0 – 200 KΩ |
| Tone Frequency Response | 0Hz to 10Khz |
| Circuit Breaker Rating | 1 – 10 Amp |
| Item Weight | 2.7kg |
| Item Dimensions (L x W x H) | 10inch x 10inch x 10inch (Approximate) |
9. Supported Motorcycle Models
The JDiag M100 Pro supports a wide range of EFI (Electronic Fuel Injection) motorcycles from various manufacturers:

Image: JDiag M100 Pro List of Supported EFI Motorcycles. This image displays a grid of motorcycle brand logos indicating compatibility.
- For OBD II
- For ADIVA
- For AEON
- For APRILIA
- For ARCTIC CAT
- For BAJAJ
- For BENELLI
- For BMW
- For BRIXTON
- For BOMBARDIER
- For HARTFORD
- For HONDA
- For HYOSUNG
- For HERO
- For INDIAN
- For KAWASAKI
- For KTM
- For KYMCO
- For MODENAS
- For PGO
- For PIAGGIO
- For ROYAL ENFIELD
- For SUZUKI
- For SYM
- For TVS
- For TRIUMPH
- For VESPA
- For YAMAHA
- For YIBEN
10. User Tips
- KTM Compatibility: This tester is designed to work with various KTM models. For specific models like KTM MX (crosser) SX 125cc, ensure you have the correct adapter cable (if not included in the OBD version, it would be in the Standard/Full version). Always check the connection port on your motorcycle against the available cables.
- Software Updates: Regularly check the JDiag website (www.jdiag.org) for software updates to ensure compatibility with the latest motorcycle models and to access new features. Updates can be performed via the USB port.
- Cable Management: Keep all diagnostic cables organized and free from kinks or damage. Damaged cables can lead to inaccurate readings or connection issues.
11. Warranty and Support
11.1 Limited One-Year Warranty
JDiag warrants to its customers that this product will be free from all defects in materials and workmanship for a period of one year from the date of original purchase, subject to the following terms and conditions:
- The sole responsibility of JDiag under the warranty is limited to either the repair or, at the option of JDiag, replacement of the test tool at no charge with proof of purchase. The sales receipt may be used for this purpose.
- This warranty does not apply to damages caused by improper use, accident, flood, lightning, or if the product was altered or repaired by anyone other than the manufacturer's service center.
- JDiag shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the test tool.
11.2 Service Procedures
If you have any questions, please contact your local store, distributor, or visit the official website at www.jdiag.org.
If it becomes necessary to return the tool for repair, contact your local distributor for more information.