Road Top 12.3" Car Multimedia Radio Linux Touch Screen For Audi Q5 2018-2019

Contents

Road Top 12.3" Car Multimedia Radio Linux Touch Screen for Audi Q5 2018-2019 User Manual

Model: 12.3" Car Multimedia Radio Linux Touch Screen For Audi Q5 2018-2019

1. Introduction

This manual provides detailed instructions for the installation, setup, operation, and troubleshooting of your new Road Top 12.3" Car Multimedia Radio Linux Touch Screen. This unit is designed to enhance your driving experience by integrating advanced multimedia features, including Wireless CarPlay and Android Auto, into your Audi Q5 (2018-2019 MIB/MIB2 Version).

For a comprehensive visual guide, please refer to the official PDF user manual available at: User manual (PDF).

2. Safety Information

Please read all instructions carefully before installation and use. Improper installation or operation may cause damage to the product, vehicle, or personal injury.

  • Ensure the vehicle's ignition is fully turned off before beginning installation. Operating or installing the unit with power on may cause permanent damage to the car audio system.
  • If you lack relevant installation experience, professional assistance is recommended.
  • Do not attempt to modify or disassemble the unit.
  • Always prioritize safe driving. Do not operate the device in a way that distracts you from the road.

3. Product Content

The package includes the following items:

  • Multimedia Smart Touchscreen (x1)
  • Screen Bracket (x1) - Note: The bracket varies depending on the vehicle model (A3, A4/A5, A6/A7, Q5).
  • Power Cable (x1)
  • AMI Cable / Screw Set (x1)
Contents of the product package including the touchscreen, bracket, power cable, and AMI cable.
Figure 3.1: Product Content Overview

4. Installation Instructions

Before proceeding, ensure the vehicle's ignition is fully turned off. For detailed visual guidance, refer to the installation videos accessible via QR codes mentioned below or in the full PDF manual.

4.1 Cable Connection Chart

This diagram illustrates the main cable connections for the head unit:

  • Head unit power cable
  • LVDS cable
  • USB cables (to be placed in the glove box)
  • Camera cable
Diagram showing the head unit with connections for power, LVDS, USB, and camera cables.
Figure 4.1: Cable Connection Chart

4.2 Head Unit Power Cable Connection

  1. Disconnect the original power cable from the head unit.
  2. Attach the original power cable to the new wiring harness.
  3. Connect the new harness to the head unit's power port.
Diagram illustrating the connection of the new power cable harness to the head unit, replacing the original OEM power cable.
Figure 4.2: Head Unit Power Cable Connection

4.3 LVDS Cable Connection

  1. Disconnect the original LVDS cable from the OEM screen.
  2. Connect it to the new Linux-compatible screen.
  3. No other cables from behind the OEM screen are required; please leave them disconnected.

Refer to the full PDF manual for a visual diagram of the LVDS cable connection.

4.4 AMI Cable Connection (For Equipped Vehicles)

If your vehicle is equipped with an AMI port, connect the provided AMI cable to enable CarPlay audio through the vehicle's AMI/AUX system.

  1. Connect the AMI cable to your car's AMI port.
  2. Ensure there is no other connection to the AMI port.

Common locations for the AMI port include the glove box, central console box, or behind media interface doors.

Diagram showing how to connect the AMI cable and images indicating common locations for the AMI port in a car.
Figure 4.3: AMI Cable Connection and Port Locations

5. Basic Setup

After installation, complete the following basic settings for proper OEM system function.

5.1 OEM System Resolution Setup

If you experience screen distortion or icon misalignment when switching to the OEM interface, adjust the resolution:

  1. Navigate to: Setup > Car Settings > Original Car's Screen Resolution.
  2. Select the corresponding resolution based on your original car's screen size:
    • 5.8 inches: MIB / MMI 3G 400X240
    • 7 or 8 inches: MIB / MMI 3G 800x480
    • 8.3 inches: MIB 1024X480
  3. To measure your original car's screen size, refer to the illustration and measure the diagonal length of the active display area.
Screenshots showing correct and incorrect OEM system resolution displays, along with a guide on how to measure the car's original screen size.
Figure 5.1: OEM System Resolution Setup and Screen Measurement

For a video guide on setting the original car's screen resolution, scan the QR code in the full PDF manual.

5.2 Sound Setup

This unit supports two audio output modes: AMI/AUX Mode and Original Bluetooth Mode. Only one mode can be active at a time.

5.2.1 AUX Audio Output Mode

  1. Disconnect any existing Bluetooth connection between your phone and the vehicle.
  2. In the Setup > System menu, set the "Use Car's BT Channel" function to OFF.
  3. Switch to OEM MIB System, navigate to Media, and select "External audio player" to set the sound input to AUX.
  4. Once "The external audio player is selected" is shown, touch the screen to return to the Linux interface. CarPlay/Android Auto sound will now play.

For a video guide on setting the AUX Audio Output Mode, scan the QR code in the full PDF manual.

5.2.2 AMI Audio Output Mode (for vehicles with AMI function)

If your vehicle has an AMI port and you have connected the AMI cable (as per Section 4.4):

  1. Disconnect any existing Bluetooth connection between your phone and the vehicle.
  2. In the Setup > System menu, set the "Use Car's BT Channel" function to OFF.
  3. Switch to OEM MIB System, navigate to Media, and select "External audio player" to set the sound input to AMI.
  4. Touch the screen to return to the Linux interface. CarPlay/Android Auto sound will now play.

For a video guide on setting the AMI Audio Output Mode, scan the QR code in the full PDF manual.

5.2.3 Original Bluetooth Mode (for vehicles with factory Bluetooth audio)

Note: This mode supports CarPlay and Android Auto only. It does not support audio from USB play, AirPlay, or Autolink.

  1. In the Setup > System menu, set the "Use Car's BT Channel" function to ON.
  2. Switch to OEM MIB System, navigate to Media, and pair your phone with the car's original Bluetooth.
  3. After pairing, leave the OEM MIB system on the Bluetooth audio screen. Then, touch the screen to return to the Linux interface. CarPlay/Android Auto sound will now play.

For a video guide on setting the Original Bluetooth Mode, scan the QR code in the full PDF manual.

5.3 Reverse Camera Setup

Note: The OEM 360° surround view is exclusively available through the OEM system and is not supported by this new system. Compatibility with aftermarket 360° cameras is also not available.

5.3.1 OEM Camera

For automatic transmission vehicles with an original factory (OEM) camera:

  1. Select "Original Camera" in the Setup > Car Settings > Reversing Settings menu.

For manual transmission vehicles with an original factory (OEM) camera:

  1. You will need to prepare a long electric wire to connect the vehicle's reversing light (12V+) to the "BACK" wire on the unit's power harness.
  2. Navigate to Setup > Car Settings > Reversing Settings.
  3. Set Camera Type to "Original Camera".
  4. Set the "Reverse Line Detection" function to ON.

Refer to the full PDF manual for specific wiring diagrams for OEM cameras.

5.3.2 Aftermarket Camera

Specification Note: Maximum supported resolution is AHD720P. 1080P is not compatible.

For automatic transmission vehicles with an aftermarket camera:

  1. In Setup > Car Settings > Reversing Settings, select "Aftermarket Camera".
  2. Connect the camera by following the provided wiring diagram (refer to the full PDF manual for the diagram). The diagram typically shows connections for Rear-Camera, Rear Camera PWR, Red (Connection), GND 12V- (No Connection).

For manual transmission vehicles with an aftermarket camera:

  1. You will need to prepare a long electric wire to connect the vehicle's reversing light (12V+) to the power extension cable of the aftermarket camera.
  2. Navigate to Setup > Car Settings > Reversing Settings.
  3. Set Camera Type to "Aftermarket Camera".
  4. Set the "Reverse Line Detection" function to ON.

Refer to the full PDF manual for specific wiring diagrams for aftermarket cameras.

Display showing the rear camera function with parking lines on the screen.
Figure 5.2: Rear Camera Function Display

6. Operating Instructions

6.1 CarPlay / Android Auto

Before using CarPlay/Android Auto, disconnect any existing Bluetooth connection between your phone and the vehicle. Then, navigate to Setup > Smart Phone > Smart Phone List and ensure the corresponding CarPlay and Android Auto functions are turned ON.

6.1.1 Wireless CarPlay / Android Auto Connection Steps:

  1. Turn on your phone's WiFi.
  2. Turn on your phone's Bluetooth.
  3. Search for and pair with the device Bluetooth named "CAR-XXXX".
  4. Confirm the Bluetooth pairing request on your phone.
  5. Allow CarPlay / Android Auto sync to your phone.
  6. Click "Connect" to use CarPlay / Android Auto function.
Screenshot of the CarPlay interface on the car's multimedia screen.
Figure 6.1: Wireless/Wired CarPlay Interface
Screenshot of the Android Auto interface on the car's multimedia screen.
Figure 6.2: Wireless/Wired Android Auto Interface

For a video guide on connecting Wireless CarPlay/Android Auto, scan the QR code in the full PDF manual.

6.1.2 Wired CarPlay / Android Auto Connection Steps:

  1. Connect your phone to this device via a high-quality data cable.
  2. Confirm the authorization request on your phone.

Before using AirPlay/AutoLink, navigate to Setup > Smart Phone > Smart Phone List and ensure the corresponding AirPlay and AutoLink functions are turned ON.

6.2.1 AirPlay Connection Steps (for iOS phones):

  1. Use your iPhone to search for the device WiFi name "CAR-XXXX" and connect to it.
  2. If a password is required, enter "66668888".
  3. Select "AirPlay" in Screen Mirroring from your iPhone.

For a video guide on connecting Wireless AirPlay, scan the QR code in the full PDF manual.

If your Android phone does not have AutoLink, you may need to download the "Autolink Pro" APP by scanning the QR code in the full PDF manual.

  1. Open the "Autolink Pro" app from your phone.
  2. Search for the WiFi "CAR-XXXX" and connect it.
  3. Allow "Autolink Pro" to use the mirror link function.
Comparison of AirPlay for iOS and AutoLink for Android, showing phone screens mirrored to the car display.
Figure 6.3: AirPlay / AutoLink Mirror Link Function

6.3 Other Features

  • Hands-Free Phone Call: Make calls, return missed calls, and listen to voice mail directly from the screen.
  • Screenshot of the hands-free phone call interface on the car's multimedia screen.
    Figure 6.4: Hands-Free Phone Call Interface
  • Navigation & Maps: Support all kinds of mainstream map applications, allowing you to travel one step faster.
  • Screenshot of the navigation and maps interface on the car's multimedia screen, showing various map app icons.
    Figure 6.5: Navigation & Maps Interface
  • Mobile Music Play: Download different music apps and link them to the homescreen menu for playback.
  • Screenshot of the mobile music playback interface on the car's multimedia screen, showing various music app icons.
    Figure 6.6: Mobile Music Play Interface
  • Siri & Google Voice Control: Keep your eyes on the road and hands on the steering wheel by using voice commands to get help finding routes, playing music, checking news, or weather.
  • Screenshot of Siri and Google Voice Control interfaces on the car's multimedia screen.
    Figure 6.7: Siri & Google Voice Control
  • Support Original Car Settings: The unit retains various OEM factory system functions, including the original system, CD/DVD player, steering wheel control, speaker sound output, reversing system, and iDrive rotation button.
  • Images showing various retained OEM car functions like factory system, CD/DVD player, steering wheel control, speaker output, reversing system, and iDrive button.
    Figure 6.8: Retained OEM Factory System Features

7. Specifications

Attribute Value
Brand NameRoad Top
Display Size12.3''
Resolution1920*720
Operating SystemLinux
Special Featureswifi function, Support 4G Network, Support Can-Bus, Support steering wheel control, Built-In Speaker/Microphone, Built-in GPS, Mobile Phone, MP3 players
Digital Media FormatMp3, MP4, WMA, JPEG
OSD LanguageFrench, Spanish, Portuguese, German, Italian, English, Russian, Hebrew
Voltage12 V
Item Weight2.7 kg
Max External MemoryOther
DinOne Din
InterfaceStandard
MaterialPlastic&ABS
For Vehicle Brands/ModelAudi
CertificationCE
OriginMainland China

8. Troubleshooting (FAQ)

Q: My OEM system screen cannot be displayed normally.

A: Please set the correct resolution in Setup > Settings > Car Settings > Original Screen Resolution. If the issue continues, scan the QR code in the full PDF manual for detailed troubleshooting video steps.

Q: My car has no sound.

A: Make sure you have properly configured either Bluetooth Audio or AMI/AUX. Only one mode can be active at a time; using both may cause no sound. For step-by-step guidance, scan the QR code in the full PDF manual for a video on sound setup.

Q: My reverse camera isn't functioning.

A: First, identify if it's an OEM or aftermarket camera, and if your vehicle has automatic or manual transmission. Then, go to Section 5.3 "Reverse Camera Setup" in this user manual and follow the corresponding setup steps.

Q: During calls, the other party reports hearing an echo.

A: Please go to Setup > Audio > Call Echo Cancellation and select "Start Auto AEC" to perform echo cancellation. For optimal call quality, ensure the vehicle interior remains quiet during this process.

A: Ensure the corresponding function is turned ON in the Setup > Smart Phone > Smart Phone List menu. If you are still unsure, scan the QR code in the full PDF manual to watch the video guide.

Q: My CarPlay / Android Auto connection keeps dropping.

A: Please try changing to a new WiFi channel in Setup > WiFi > Channel.

Q: Which steering wheel controls are compatible with this product?

A: The steering wheel supports volume adjustment, track skip, phone call answering, and voice control keys. Compatible only with vehicles equipped with a multi-function steering wheel.

Q: Does the product work with the original car microphone?

A: Yes, the original car microphone is supported via original Bluetooth Audio mode. Please scan the QR code in the full PDF manual for video instructions on sound setup.

9. User Tips

  • This unit is designed to upgrade your existing Audi Q5 system, adding features like CarPlay and Android Auto even if your original system did not have them. It's a screen replacement that enhances functionality.
  • Always ensure your phone's Bluetooth and WiFi are properly configured and disconnected from other devices before attempting to connect to the multimedia unit for CarPlay or Android Auto.
  • For optimal performance, use high-quality data cables for wired connections.

10. Warranty & Support

For support, contact us via your purchase platform, email, or WhatsApp. Please include the following information for faster resolution:

  1. Order ID
  2. Vehicle model and year
  3. Detailed issue description. A video (preferably showing wiring) or photos are highly recommended.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.