Lishui Controller X863-AA024

Contents

Ebike Brushless Motor Controller X863-AA024 User Manual

Model: X863-AA024

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your Lishui Controller X863-AA024 Brushless Motor Controller. This controller is designed for use with electric bicycles, electric scooters, fat bikes, and mountain bikes (MTB).

Important Note: This controller is specifically designed for use with 2HAO protocol display meters. Incompatible display protocols will result in errors and improper functionality. Always verify the model number of your controller and ensure compatibility with your display meter before installation. If you are unsure, please consult customer service with photos of your controller's label and connectors.

Important note on controller model verification
Figure 1: Important note regarding model number verification for compatibility.

Product Overview Video

Video 1: A brief overview of the Ebike Brushless Motor Controller X863-AA024, showcasing its physical appearance and various connectors.

2. Specifications

The Lishui Controller X863-AA024 is a robust brushless motor controller with the following technical specifications:

AttributeValue
ModelX863-AA024
TypeController
OriginMainland China
Dimensions (L x W x H)83mm x 51mm x 29mm
Battery Voltage36V/48V
Current Limit12A
Product Weight170g
Compatible Display Meter2HAO Protocol
High-Concerned ChemicalNone
Ingress Protection (IP) RatingIPX5 (Water jet resistant)
Product dimensions of the controller
Figure 2: Dimensions of the X863-AA024 Brushless Motor Controller.
Top view of the controller showing the model label
Figure 3: Top view of the controller, highlighting the model label with specifications.

3. Setup and Installation

Proper installation is crucial for the safe and efficient operation of your ebike or electric scooter. Refer to the wiring diagram below for connecting the controller to your system components.

Wiring diagram for the brushless motor controller
Figure 4: Detailed wiring diagram for the X863-AA024 Brushless Motor Controller.

Wiring Connections:

  1. Power Supply (Main): Connect the primary power input from your battery.
  2. Motor Hall / Tachometer Signal: Connect to the motor's Hall sensors and tachometer signal for speed feedback.
  3. Assistance (PAS Sensor): Connect to the Pedal Assist System (PAS) sensor.
  4. Throttle & Brake & Display: This bundle typically includes connections for the throttle, brake levers (often with cut-off switches), and the 2HAO display meter.
  5. Power Supply (Auxiliary): Secondary power input, if applicable.
  6. Tail Light: Connect to the vehicle's tail light.
  7. Reserved Interface: For future expansion or specific accessories.
  8. Motor Cables (8, 9, 10): Connect these three cables to the corresponding motor phase wires. Ensure correct phase matching for smooth motor operation.

Ensure all connections are secure and insulated to prevent short circuits. Incorrect wiring can damage the controller and other components.

4. Operating Instructions

The Lishui Controller X863-AA024 manages the power delivery to your ebike or electric scooter motor based on inputs from the throttle, pedal assist sensor, and brake levers. It is designed to work seamlessly with 2HAO protocol display meters.

Basic Operation:

  • Power On/Off: Typically controlled via your 2HAO display meter. Refer to your display meter's manual for specific power procedures.
  • Throttle Control: Apply throttle to engage the motor and control speed.
  • Pedal Assist System (PAS): When pedaling, the PAS sensor detects your pedaling input and the controller provides motor assistance. The level of assistance is usually adjustable via your display meter.
  • Brake Function: Engaging the brake levers will cut off motor power, ensuring safe stopping.
  • Display Meter Functions: Your 2HAO display meter will show essential information such as speed, battery level, and potentially allow adjustment of PAS levels and light control.

Advanced Features (Lishui Controller Technology):

  • Hall-Sensorless Motor Technology: This controller utilizes advanced hall-sensorless technology, which can lead to lower maintenance costs and reduced interference compared to traditional hall-sensor systems. It supports zero-start functionality even under heavy loads.
  • OTA Functions Compatibility: Lishui controllers can be programmed to be compatible with various IoT devices, including Battery Management Systems (BMS) and Bluetooth data exchange.
  • Longer Driving Distance: Features like regeneration braking and precise adjustments contribute to extended mileage and protection against overheating.
  • Customization Software: Lishui Controller offers software for customization, allowing users to adjust parameters to match different pedals, displays, torque sensors, and motors.

5. Maintenance

To ensure the longevity and optimal performance of your X863-AA024 controller, follow these general maintenance guidelines:

  • Keep Dry: Protect the controller from water and excessive moisture. While rated IPX5, prolonged exposure to water can cause damage.
  • Cleanliness: Periodically clean the exterior of the controller with a dry or slightly damp cloth. Avoid using harsh chemicals.
  • Inspect Connections: Regularly check all wiring connections for tightness and signs of corrosion or damage. Loose connections can lead to intermittent operation or component failure.
  • Avoid Physical Damage: Protect the controller from impacts and vibrations. Mount it securely in a protected location on your vehicle.
  • Temperature Management: Ensure the controller is mounted in a location with adequate airflow to prevent overheating, especially during prolonged use or high loads.

6. Troubleshooting

If you encounter issues with your X863-AA024 controller, consider the following troubleshooting steps:

  • No Power/No Response:
    • Check battery connections and ensure the battery is charged.
    • Verify all power supply wires (1 and 5 in the wiring diagram) are securely connected.
    • Ensure the display meter is powered on and functioning.
  • Motor Not Engaging/Intermittent Power:
    • Confirm that the display meter is of the 2HAO protocol. Incompatible protocols will prevent proper operation.
    • Check throttle and PAS sensor connections (part of bundle 4 and connection 3).
    • Inspect motor cables (8, 9, 10) for secure connections and damage.
    • Ensure brake levers are not engaged, as they cut motor power.
  • Error Codes on Display:
    • Refer to your 2HAO display meter's manual for specific error code interpretations and solutions.
    • Common issues often relate to sensor malfunctions, motor connection problems, or battery voltage irregularities.
  • Overheating:
    • Reduce load or speed.
    • Ensure the controller has adequate ventilation.
    • Check for any obstructions around the controller that might impede airflow.

If the problem persists after performing these checks, please contact customer support for further assistance.

7. User Tips

  • Always double-check the model number and display protocol compatibility before purchasing and installing a new controller to avoid operational issues.
  • For optimal performance and longevity, ensure all electrical connections are clean, tight, and properly insulated.
  • Consider using the customization software (if available and accessible) to fine-tune controller parameters for your specific ebike setup and riding preferences.

8. Warranty and Support

Lishui Controller is committed to providing reliable products and excellent customer service. Your X863-AA024 controller is backed by our service commitments.

Service Commitments:

  • Free Returns: Enjoy free returns within 90 days of purchase.
  • Fast Delivery & Refunds for Issues:
    • Refund if package is lost.
    • Refund if items are damaged upon arrival.
    • Refund if no delivery within 30 days.
  • Security & Privacy: We ensure safe payments and secure personal details, not sharing them with third parties without your consent.

Contact Information:

For technical support, warranty claims, or any inquiries, please contact Lishui Controller through the following channels:

  • Nanjing Lishui Electronics Research Institute Co., Ltd (Headquarters):
    • Address: No.9 Shuibao Road, Yongyang Town, Lishui District, Nanjing, 211200, P.R.China
    • Tel: +86-25-5720-2368 / +86-25-5720-7820
    • Fax: +86-25-5721-2368
    • Email: sales@lsdzs.com
  • EU R&D Center:
    • Address: Am Bahnhof 21, 53757 Sankt Augustin, Germany
    • Mobile: +49 15221467527
    • Tel: +49-2241-9454576
    • Fax: +49-2241-9454577
    • Email: info@lsee.eu
  • Taiwan Office:
    • Address: No.450, Fuxing Rd., Taoyuan Dist., Taoyuan City 330, Taiwan
    • Tel: +886 3-333 2298
    • Fax: +886 3-333 3843

You can also visit our website: www.lsdzs.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.