Jonsbo ZA-420/140 Series

Contents

Jonsbo ZA-420/140 Series Computer Case Fan User Manual

Model: ZA-420/140 Series

Brand: Jonsbo

1. Product Overview

The Jonsbo ZA-420/140 series computer case fans are designed to provide efficient cooling and customizable ARGB lighting for your PC. These fans feature a unique DIY exchangeable fan blade design, allowing for both forward and reverse airflow configurations and different aesthetic effects. The ZA-140 is a single 140mm fan, while the ZA-420 is a triple 140mm fan unit.

Jonsbo ZA-420/140 fan with interchangeable blades and ARGB lighting

Image: Jonsbo ZA-420/140 fan showcasing its design with interchangeable blades and ARGB lighting.

2. Package Contents

Please verify that all components are present in your package:

  • Jonsbo ZA-420 (triple fan unit) or ZA-140 (single fan unit)
  • Two sets of interchangeable fan blades (for DIY customization)
  • Lubricating oil (for maintenance)
  • Mounting screws
  • User Manual (this document)

3. Setup and Installation

3.1 Fan Blade Exchange

The fan comes with two sets of fan blades, allowing you to customize the airflow direction (forward or reverse) and achieve different lighting effects. To exchange the fan blades:

  1. Carefully remove the existing fan blades from the motor hub.
  2. Align the desired set of fan blades with the motor hub and gently press them into place until secure.
Diagram showing fan blade exchange for a black fan unit

Image: Illustration of the fan blade exchange process for a black fan unit.

Diagram showing fan blade exchange for a white fan unit

Image: Illustration of the fan blade exchange process for a white fan unit.

3.2 Mounting the Fan

Mount the fan(s) securely into your computer case using the provided screws. Ensure proper orientation for desired airflow (refer to Section 4.1 for airflow direction).

3.3 Connecting the Fan

The Jonsbo ZA-420/140 fans utilize a single cable for both power and ARGB control, simplifying cable management within your chassis.

  • PWM 4PIN Connector: Connect the 4-pin PWM connector to an available fan header on your motherboard. This allows for speed control based on system temperature.
  • ARGB 3PIN (5V) Connector: Connect the 3-pin 5V ARGB connector to a compatible ARGB header on your motherboard or an external ARGB controller. This enables synchronization of lighting effects. The 5V ARGB plug features male and female designs, allowing for daisy-chaining with other ARGB devices.
Triple fan unit connected to motherboard with single cable

Image: Triple fan unit connected to the motherboard with a single cable for streamlined management.

ARGB connection diagram and software interface

Image: Diagram illustrating the 5V 3PIN ARGB connection to a motherboard and a software interface for controlling lighting effects.

4. Operating Instructions

4.1 Airflow Direction (Forward vs. Reverse)

The interchangeable fan blades allow you to configure the fan for either forward or reverse airflow. This is crucial for optimizing cooling within your PC case.

  • Forward Fan: Draws air into the case.
  • Reverse Fan: Pushes air out of the case.

Refer to the diagram below to understand the airflow direction based on the fan blade orientation.

Diagram illustrating Forward and Reverse airflow directions

Image: Visual representation of air inlet and outlet surfaces for both Forward and Reverse fan configurations.

4.2 Fan Speed Control (PWM)

The 4-pin PWM connector allows your motherboard to dynamically control the fan speed based on CPU or system temperatures. This ensures optimal cooling performance while minimizing noise when not under heavy load. You can typically configure fan curves in your motherboard's BIOS/UEFI settings or through manufacturer-provided software.

4.3 ARGB Lighting Control

The 5V 3-pin ARGB connector enables synchronization with compatible motherboard software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) or an external ARGB controller. This allows you to customize lighting effects, colors, and patterns across your system.

Integrated fan grille lighting effect

Image: Close-up view of the integrated fan grille lighting effect.

5. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your Jonsbo fans.

  • Cleaning: Periodically clean the fan blades and housing to remove dust buildup. Use compressed air or a soft brush. Ensure the fan is powered off before cleaning.
  • Lubrication: The fan comes with lubricating oil. If you notice increased noise or reduced performance over time, a small amount of lubricant can be applied to the fan bearing. Refer to the fan's design for the lubrication point, typically under a sticker on the fan hub.
  • Inspection: Check cables for any signs of wear or damage. Ensure all connections are secure.

6. Troubleshooting

If you encounter issues with your Jonsbo fan, try the following troubleshooting steps:

  • Fan Not Spinning:
    • Check if the 4-pin PWM connector is securely plugged into the motherboard fan header.
    • Ensure the fan header is enabled in your motherboard's BIOS/UEFI settings.
    • Verify that your power supply is providing adequate power.
    • Test the fan on a different fan header or with a fan controller if available.
  • ARGB Lights Not Working:
    • Ensure the 3-pin 5V ARGB connector is correctly plugged into a compatible ARGB header (not a 12V RGB header, which can damage the LEDs).
    • Check your motherboard's ARGB software or external controller settings to ensure lighting is enabled and configured.
    • Verify that the ARGB header on your motherboard is functioning correctly.
    • If daisy-chaining, ensure all connections are secure.
  • Excessive Noise:
    • Ensure the fan is securely mounted and not vibrating against the case.
    • Check for any cables or obstructions hitting the fan blades.
    • Clean any dust buildup on the fan blades.
    • Consider applying a small amount of lubricating oil to the fan bearing if it's an older fan.

7. Specifications

7.1 ZA-140 (Single Fan)

FeatureSpecification
Fan Size140mm (L) * 140mm (W) * 28mm (H)
Bearing TypeFluid Bearing (Hydraulic bearing)
Fan Speed700-1800 RPM (± 10%)
Airflow Volume33.70-73.82 CFM
Wind Pressure0.47-1.94 mmH2O
Noise Level18.3-32.2 dB(A)
Rated VoltageFAN DC12V, LED 5V
Rated CurrentFAN 0.13A, LED 0.64A
Power ConsumptionFAN 1.56W, LED 3.2W
MTTF (Lifetime)≥ 20000h (Room Temp: 25℃)
ConnectorPWM 4PIN, ARGB 3PIN
Blade Quantity7
Used ForCase
Product parameters table for the Forward fan (ZA-420)

Image: Detailed product parameters for the ZA-140 Forward fan.

7.2 ZA-420 (Triple Fan Unit)

FeatureSpecification
Fan Size422mm (L) * 143mm (W) * 28mm (H)
Bearing TypeFluid Bearing (Hydraulic bearing)
Fan Speed700-1500 RPM (± 10%)
Airflow Volume34.8-64.49 CFM
Wind Pressure0.45-1.33 mmH2O
Noise Level18.3-30.6 dB(A)
Rated VoltageFAN DC12V, LED 5V
Rated CurrentFAN 0.28A, LED 2.11A
Power ConsumptionFAN 3.36W, LED 10.55W
MTTF (Lifetime)≥ 20000h (Room Temp: 25℃)
ConnectorPWM 4PIN, ARGB 3PIN
Blade Quantity7
Used ForCase
Product parameters table for the Reverse fan (ZA-420)

Image: Detailed product parameters for the ZA-420 Reverse fan.

7.3 Noise and RPM Comparison

Noise and RPM comparison for Forward and Reverse fans

Image: Comparison table showing noise levels (dB(A)), RPM, and CFM for both Forward and Reverse fan configurations.

8. User Tips

  • Optimize Airflow: Plan your case fan layout carefully. Use forward fans for intake (bringing cool air in) and reverse fans for exhaust (pushing hot air out) to create a positive or negative pressure system as desired for optimal cooling.
  • ARGB Customization: Experiment with your motherboard's ARGB software to create unique lighting effects that match your build's aesthetic. The daisy-chaining feature allows for synchronized lighting across multiple fans and other ARGB components.
  • Cable Management: Utilize the single-cable design to keep your PC build clean and organized. Route cables behind the motherboard tray where possible.

9. Warranty and Support

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty validation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.