MESTEK CBF01

Contents

MESTEK CBF01 Circuit Breaker Finder & GFCI Outlet Tester User Manual

Model: CBF01 | Brand: MESTEK

1. Introduction

1.1 Product Overview

The MESTEK CBF01 is a digital circuit breaker finder kit, comprising a transmitter and a receiver. This device is designed to locate and control specific outlets or circuits by identifying the correct circuit breaker in a distribution panel. The transmitter injects a signal into the target circuit, which is then detected by the receiver to precisely locate the circuit breaker.

1.2 Safety Symbols

  • ⚠ Safety Warning: Indicates important information requiring attention to prevent electric shock or fatalities. Read the instruction manual carefully.
  • 📖 Read Manual: Please ensure you have read the user manual thoroughly before using the product.
  • ⚡ Electric Shock Hazard: Use electricity with caution and take appropriate protective measures.
  • ✅ ETL Certification: This device has passed rigorous testing and inspection by ETL, complying with relevant safety and quality standards.

1.3 General Safety Precautions

  • This device is intended for testing AC 120V power outlets in North America only. Do not use it to measure high voltage.
  • Before use, inspect the product for any damage during transportation. If damage is found, discontinue use.
  • Always test the unit on a known live and correctly wired circuit to verify its function before use.
  • When using the transmitter's "GFCI" function, ensure the tested line is correctly wired and a circuit breaker is installed. Turn off other electrical equipment on the line before testing to prevent hazards. Do not use this function if unsure of its purpose.
  • Before testing, remove other equipment or devices connected to the circuit to prevent interference.
  • If using accessories to connect to exposed wires, disconnect the circuit power before using the device. Ensure the circuit is not live when removing the transmitter.
  • If you lack professional electrical knowledge, consult a qualified electrician in complex situations.
  • Do not leave the product plugged into an outlet for extended periods. Remove it after use.
  • All appliances or equipment on the circuit being tested should be unplugged to help avoid erroneous readings.
  • This is a simple instrument to detect common improper wiring conditions, not a comprehensive diagnostic instrument.
  • Refer all indicated problems to a qualified electrician.
  • The device will not indicate the quality of the ground, detect two hot wires in a circuit, detect a combination of defects, or indicate reversal of grounded and grounding conductors.
  • Consult the GFCI manufacturer's installation instructions to ensure proper installation.
  • When testing GFCIs in 2-wire systems (no ground wire), the tester may give a false indication. Recheck GFCI operation using its test and reset buttons.

1.4 Intended Use and Environment

The circuit breaker finder kit is for indoor use, pollution degree 2, CAT II 135V 50/60Hz.

  • CAT I: Suitable for low-energy electrical connections (e.g., electronic devices).
  • CAT II: Suitable for household appliances, portable devices, and low-voltage circuits in buildings.
  • CAT III: Suitable for equipment connected to the distribution part of the power supply (e.g., distribution boxes).
  • CAT IV: Suitable for equipment connected to the main power source (e.g., indoor/outdoor distribution systems).

For a detailed user manual, please refer to the MESTEK CBF01 User Manual (PDF).

2. Product Appearance and Components

The MESTEK CBF01 consists of two main parts: the Transmitter (Outlet Tester) and the Receiver (Circuit Breaker Finder).

MESTEK CBF01 Dual-Purpose Circuit Breaker Finder with labeled parts and dimensions

Figure 2.1: MESTEK CBF01 Dual-Purpose Circuit Breaker Finder with labeled parts and dimensions. Transmitter (left) is 4.48in (114mm) tall and 2.20in (56mm) wide. Receiver (right) is 7.87in (200mm) tall and 1.18in (30mm) wide.

2.1 Transmitter Components

Diagram of MESTEK CBF01 Transmitter and Receiver with numbered parts

Figure 2.2: Detailed diagram of the MESTEK CBF01 Transmitter and Receiver with numbered components.

Transmitter Parts Description
No.Description
①Plug
②Display
③Power Switch, Reset Button
④GFCI Test Button
⑤Indicator Light (Green) Correct
⑥Indicator Light (Red) Fault
⑦Battery Cover

2.2 Receiver Components

Receiver Parts Description
No.Description
⑧Sensing Probe
⑨Detection Indicator Light (Green)
⑩Display
⑪Detection Signal Indicator Light (Red)
⑫Power Switch, Test Button
⑬Battery Cover

3. Technical Specifications

3.1 Symbols and Meanings

MESTEK CBF01 Display and Symbols Table

Figure 3.1: MESTEK CBF01 Receiver Display and table of symbols with their meanings.

Transmitter Display Symbols
SymbolMeaning
GFCICircuit breaker
HOLDHold indication
DBattery under-voltage indication
>Greater than
<Less than
⚡Live wire danger
SECSecond
VVoltage
ACAlternating current
CORRECT (Green)Correct wiring
OPEN NEU (Red)Neutral Wire Open
OPEN GRD (Red)Ground wire open
HOT/GRD REV (Red)Hot/ground wire reversed
HOT/NEU REV (Red)Hot/neutral wire reversed
OPEN HOT (Red)Hot wire Open
OPEN GRD NEU (Red)Ground/neutral wire open
Receiver Display Symbols
SymbolMeaning
ΠLow Battery Indicator
LearnLearn mode
ScanScan mode

3.2 Technical Parameters Table

MESTEK CBF01 Technical Parameters Table

Figure 3.2: Detailed technical parameters for the MESTEK CBF01 Transmitter and Receiver.

MESTEK CBF01 Technical Parameters
ParameterTransmitter (Outlet Tester)Receiver (Circuit Breaker Finder)
Product TypeCircuit Breaker FinderCircuit Breaker Finder
DisplayVA Negative DisplayVA Negative Display
Working Altitude2000m2000m
Alarm MethodScreen Display, Indicator Light, Buzzer AlarmScreen Display, Indicator Light, Buzzer Alarm
Operating VoltageAC 90V~135V / 50Hz/60HzAC 90V~135V / 50Hz/60Hz
Battery1.5V AAA × 21.5V AA × 2
Auto Power OffAbout 3 minutesAbout 15 minutes
Operating CurrentAbout 30mAAbout 40mA
GFCI Leakage CurrentAbout 6mA~9mAN/A
Working Environment32°F~122°F (0-50°C) / <75% RH32°F~122°F (0-50°C) / <75% RH
Storage Environment-4°F~122°F (-20°C~50°C) / 0%-75% RH (without battery)-4°F~122°F (-20°C~50°C) / 0%-75% RH (without battery)
Size114 × 56 × 30 mm (4.18 × 2.20 × 1.18 in)200 × 46 × 30 mm (7.87 × 1.81 × 1.18 in)
Weight (without battery)85 g (2.99 oz)96 g (3.35 oz)

4. Setup and Operation

4.1 Using the Outlet Tester (Transmitter)

The transmitter functions as an outlet tester to detect and identify common wiring faults.

MESTEK CBF01 Transmitter detecting common wire faults

Figure 4.1: MESTEK CBF01 Transmitter displaying various wiring fault types for North American 3-wire 120V electrical outlets.

4.1.1 Basic Functions

  • Power On/Off: Press and hold the power button (③) for about 1 second to turn the transmitter on or off.
  • Automatic Shutdown: The device will automatically shut down after approximately 3 minutes of inactivity. Press any button to reset this timer. This function is inactive during testing.
  • HOLD Function: After measurement, if the device is unplugged, the screen will display "HOLD" and the current measurement indicator will flash, locking the data for about 10 seconds. To quickly release the lock, plug the device back into the circuit or press the power button (③).

4.1.2 Wiring Fault Detection

Insert the transmitter into the outlet to be tested. The screen will display the current voltage and wiring status. If the circuit is not connected or the hot wire is open, the screen will display "OPEN HOT".

MESTEK CBF01 Transmitter showing correct and faulty wiring indications

Figure 4.2: MESTEK CBF01 Transmitter indicating correct wiring (green light) and wiring error (red light).

  • CORRECT Wiring: The screen displays the current voltage and "CORRECT", and the green indicator light (⑤) turns on.
  • OPEN NEU (Open Neutral): The screen displays "OPEN NEU" and the red indicator light (⑥) turns on. This indicates the voltage between the hot wire and the ground wire is greater than AC 30V.
  • OPEN GRD (Open Ground): The screen displays "OPEN GRD" and the red indicator light (⑥) turns on, indicating incorrect wiring.
  • HOT/NEU REV (Hot and Neutral Reversed): The screen displays "HOT/NEU REV" and the red indicator light (⑥) turns on, indicating incorrect wiring.
  • HOT/GRD REV (Hot and Ground Reversed): The screen displays "HOT/GRD REV" and the red indicator light (⑥) turns on, indicating incorrect wiring.
  • OPEN HOT (Open Hot Wire): The screen displays "OPEN HOT" and the red indicator light (⑥) turns on, indicating incorrect wiring.

4.1.3 GFCI Test Function

To test the GFCI function, press the "TEST" button (④). Ensure the circuit is correctly wired and a circuit breaker is installed before testing. If the screen shows a wiring error, do not proceed with the GFCI test. If the circuit breaker trips within approximately 3 seconds, the screen will display the trip time, indicating a normal circuit. If the circuit breaker does not trip (screen displays a time over 6 seconds), there may be a wiring error or a faulty circuit breaker. Consult a professional electrician.

4.2 Using the Circuit Breaker Finder (Receiver)

The receiver is used in conjunction with the transmitter to locate the correct circuit breaker in the distribution panel.

Video 4.1: A short demonstration of the MESTEK CBF01 in use, showing the transmitter plugged into an outlet and the receiver scanning a circuit breaker panel.

MESTEK CBF01 in use, showing transmitter in outlet and receiver scanning a circuit breaker panel

Figure 4.3: The MESTEK CBF01 in action, illustrating the transmitter connected to an electrical outlet and the receiver being used to scan the distribution panel to locate the correct breaker.

4.2.1 Basic Functions

  • Power On/Off: Press and hold the power button (⑫) for about 1 second to turn the receiver on or off.
  • Modes: When turned on, the screen displays "Learn" mode. Press the power button (⑫) to enter "Scan" mode. Press it again to reset the receiver and return to "Learn" mode.
  • Reset: Resetting the receiver clears previously stored scanning data in "Learn" mode. To reset, ensure the receiver is away from the circuit breaker panel to avoid detecting the transmitter's signal. Press the "RESET" button to clear learned data and restart the scanning and learning process.

4.2.2 Scanning Procedure

  1. Insert the transmitter into the power outlet of the circuit you wish to identify. Ensure the transmitter indicates the outlet is live and correctly wired. If incorrect wiring is indicated, stop the test and consult a professional electrician.
  2. Turn on the receiver. It will start in "Learn" mode, indicated by "Learn" on the screen and a green probe indicator (⑨) with a "pulse" sound.
  3. In "Learn" mode, place the sensing probe (⑧) vertically against each circuit breaker on the distribution panel. Slowly move the probe across all breakers to allow the receiver to learn the strongest signal emitted by the transmitter. Ignore the "pulse" sound and display indicators during this phase.
  4. After learning, press the power button (⑫) to stop the "pulse" sound and enter "Scan" mode. The LCD will show "Scan".
  5. Again, place the sensing probe (⑧) vertically against each circuit breaker on the panel. When the probe approaches the correct circuit breaker connected to the transmitter's circuit, the green probe indicator (⑨) will turn off, the red signal indicator (⑪) will turn on, the device will emit a "pulse" sound, and the analog signal on the screen will increase, indicating that the correct circuit breaker has been found.

5. Maintenance

5.1 Battery Replacement

To avoid incorrect measurements, replace the batteries immediately when the low battery symbol (D for transmitter, Π for receiver) appears on the screen. Always disconnect the device from the circuit before replacing batteries.

5.1.1 Transmitter Battery Replacement (1.5V AAA × 2)

  1. Loosen the screws of the battery cover (⑦) with a Phillips screwdriver.
  2. Open the battery cover and remove the old batteries.
  3. Insert two new AAA batteries into the battery compartment, ensuring correct polarity.
  4. Close the battery cover and tighten the screws.

5.1.2 Receiver Battery Replacement (1.5V AA × 2)

  1. Use a Phillips screwdriver to loosen the screws of the product battery cover (⑬).
  2. Open the battery cover and remove the old battery.
  3. Insert two new AA batteries into the device, ensuring correct polarity. Incorrect polarity may prevent the device from operating.
  4. Close the battery cover and tighten the fixing screws.

5.2 Daily Care and Cleaning

  • If dust or stains are present on the device surface, wipe it with a damp, dust-free cloth. Ensure the device is completely dry before use.
  • Do not use corrosive cleaning agents on the device surface.
  • Store the device in a dry, temperature-controlled environment, away from direct sunlight and moisture.
  • Keep the device away from strong electromagnetic fields, vibrations, and corrosive environments to prevent interference or damage.
  • If the device will not be used for an extended period, remove the batteries before storage to prevent leakage and corrosion.

6. Troubleshooting

  • Device not powering on: Check battery levels and ensure they are inserted with correct polarity. Replace batteries if low.
  • Inaccurate readings or inability to find breaker:
    • Ensure the transmitter is plugged into a live and correctly wired AC 120V outlet.
    • Verify the receiver probe is held vertically against the circuit breaker panel during both "Learn" and "Scan" modes.
    • Make sure all other appliances on the circuit are unplugged to avoid interference.
    • Reset the receiver to clear previous data and restart the learning/scanning process.
  • GFCI test fails to trip: If the GFCI tester fails to trip the GFCI, it suggests either a wiring problem with an operable GFCI or proper wiring with a faulty GFCI. Consult a qualified electrician to diagnose the issue.
  • Wiring error indicated: If the transmitter displays a wiring error, do not proceed with GFCI testing or further use until the wiring issue is resolved by a qualified electrician.
  • Device damage: If any damage is found on the device, discontinue use immediately.

7. User Tips

  • Voltage Compatibility: This device is specifically designed for North American AC 120V electrical outlets. It is not suitable for 220V systems.
  • Initial Check: Many users find the product to be reliable and work properly right out of the box. Always perform the initial test on a known good circuit as recommended in the manual to confirm functionality.
  • Patience with Scanning: When using the receiver, move the probe slowly and deliberately across each circuit breaker. Rushing the scan can lead to missed detections or inaccurate results.
  • Clear the Area: For best results, ensure the area around the circuit breaker panel is clear of obstructions and other electrical devices that might cause electromagnetic interference.

8. Warranty and Support Information

For warranty information, technical support, or service inquiries, please contact the seller or the manufacturer directly. Keep your purchase receipt as proof of purchase.

9. Disposal and Recovery

Please do not dispose of the device or its accessories in household trash. These items must be disposed of properly according to local regulations for electronic waste. For more information, please consult your local waste management authority or visit relevant environmental protection websites such as www.epa.gov or www.erecycle.org.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.