SPATEC SMT-HSN-MD4-RD4

Contents

SPATEC SMT-HSN-MD4-RD4 Vacuum Element Integrated Vacuum Generator

Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the SPATEC SMT-HSN-MD4-RD4 Integrated Vacuum Generator. This device is designed to efficiently generate vacuum for various industrial applications, typically involving pneumatic systems and vacuum gripping.

Specifications

FeatureSpecification
ModelSMT-HSN-MD4-RD4
BrandSPATEC
TypeIntegrated Vacuum Generator
ColorRed/Gold
Solenoid Valve ModelDR100-5
Solenoid Voltage24V DC
Solenoid Power0.85W
Operating Pressure Range0 - 0.7 Mpa (0 - 7 kgf/cm²)
Battery IncludedNo
High-concerned chemicalNone
PackageNo (refers to retail packaging)
OriginMainland China
CertificationNone

Setup

The SPATEC SMT-HSN-MD4-RD4 is an integrated vacuum generator designed for easy integration into pneumatic systems. Proper setup is crucial for optimal performance and safety.

  1. Identify Ports: Locate the "EX" (Exhaust) and "V" (Vacuum) ports on the unit. The "EX" port is for expelling air, and the "V" port is where the vacuum is generated and connected to the application (e.g., vacuum cup).
    Close-up of EX and V ports on the vacuum generator

    Figure 1: Close-up view of the Exhaust (EX) and Vacuum (V) ports.

  2. Pneumatic Connections:
    • Connect your compressed air supply to the inlet port (not explicitly labeled but implied by the diagram and function). Ensure the air supply pressure is within the operating range of 0-0.7 Mpa.
    • Connect the "V" (Vacuum) port to your vacuum application, such as a vacuum cup or suction pad.
    • Ensure the "EX" (Exhaust) port is clear and unobstructed to allow for proper air expulsion.
    Top view of SPATEC vacuum generator with pneumatic diagram

    Figure 2: Top view showing the model number and an integrated pneumatic diagram. The diagram illustrates the internal valve, vacuum generation, and connections for air supply, vacuum, and exhaust.

  3. Electrical Connections: The unit features a DR100-5 solenoid valve for control.
    • Connect a 24V DC power supply to the terminals of the DR100-5 solenoid valve.
    • Ensure correct polarity if specified by the solenoid valve manufacturer (typically indicated on the valve itself).
    • The solenoid consumes 0.85W. Ensure your power supply can provide adequate current.
    Close-up of DR100-5 solenoid valve with electrical specifications

    Figure 3: Close-up of the DR100-5 solenoid valve, detailing its electrical requirements (24V DC, 0.85W) and pressure range.

  4. Mounting: Securely mount the vacuum generator in a stable position using appropriate fasteners through the mounting holes provided.

Operating Instructions

Once properly installed and connected, the SPATEC SMT-HSN-MD4-RD4 vacuum generator operates as follows:

  1. Power On: Ensure the compressed air supply is active and providing pressure within the specified range (0-0.7 Mpa).
  2. Activate Vacuum: Apply 24V DC power to the DR100-5 solenoid valve. This will actuate the internal valve, initiating vacuum generation at the "V" port.
  3. Deactivate Vacuum: Remove the 24V DC power from the DR100-5 solenoid valve. This will de-actuate the internal valve, stopping vacuum generation and typically releasing the vacuum at the "V" port.
  4. Monitoring: If your system includes a vacuum gauge, monitor the vacuum level to ensure it meets your application requirements.

Caution: Always ensure that all pneumatic and electrical connections are secure before operating the unit.

Maintenance

Regular maintenance helps ensure the longevity and reliable operation of your vacuum generator.

  • Cleanliness: Keep the unit clean and free from dust, debris, and moisture.
  • Air Quality: Ensure the compressed air supply is clean, dry, and filtered to prevent contaminants from entering the vacuum generator.
  • Connections: Periodically check all pneumatic and electrical connections for tightness and signs of wear. Replace any worn or damaged tubing or wiring.
  • Exhaust Port: Ensure the exhaust port ("EX") remains clear and unobstructed.

Troubleshooting

If you encounter issues with your SPATEC SMT-HSN-MD4-RD4, refer to the following common troubleshooting steps:

ProblemPossible CauseSolution
No vacuum generatedNo compressed air supply
Solenoid not receiving power
Blocked air inlet/exhaust
Leak in vacuum line
Check air supply and pressure
Verify 24V DC power to solenoid
Inspect and clear ports
Check all vacuum connections for leaks
Weak vacuumLow compressed air pressure
Partial blockage
Small leak in vacuum line
Increase air supply pressure (within limits)
Clean ports and internal passages
Inspect vacuum connections for minor leaks
Solenoid not actuatingNo 24V DC power
Incorrect wiring
Faulty solenoid
Check power supply and connections
Verify wiring according to diagram
Replace solenoid if faulty

User Tips

No specific user tips are available at this time. Always refer to the specifications and instructions for safe and effective use.

Warranty & Support

This product comes with a 60-day warranty for money back or exchange. For technical support or warranty claims, please use the contact information below.

60 Days Warranty badge for money back or exchange

Figure 4: Warranty information.

Contact Information:

  • WhatsApp: +86 18575513079
  • WeChat: 18575513079
  • Email: 357303203@qq.com

© 2023 SPATEC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.