1. Safety Information
To avert fire, electric shock, and potentially dangerous situations, please leave servicing and installation to only qualified personnel.
- Use only in cars with a 12-volt negative ground. Ensure the unit is grounded to a negative 12V DC power supply. Do not connect the unit to DC 24V.
- If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you might cause a short circuit, which could potentially start a fire. Always connect those wires to the power source running through the fuse box.
- For safety, make sure to insulate any loose wires with electrical tape.
- Using the head unit for a long time with the engine off can drain the battery.
- Do not watch or fix your gaze on the unit's display whilst driving for any extended period. Don't listen to loud music whilst driving. Excessive volume levels that mask sounds such as emergency vehicle sirens or road warning signals can be dangerous and may lead to an accident.
- Do not install the unit in a spot exposed to humidity or water.
- Never leave any metal items (like coins or metal tools) or liquid inside the unit. If this occurs, please turn off the car ignition to prevent short circuits or fire and consult your mechanic or XTRONS customer support.
- If you hear strange noises, smell strange odours, and/or detect smoke from the product, immediately turn the car ignition off and unplug the product to avoid short circuits or fire, and consult your mechanic or XTRONS customer support.
- Do not disassemble or modify the product in any way. Doing so may result in fire. If you experience problems during installation, consult your mechanic or XTRONS customer support.
- Do not block vents or heat dissipation panels. Doing so may cause heat to build up inside and may result in fire.
- Please bear in mind that whilst the navigation system / parking / reversing sensors are designed to make your driving simpler and safer, they do not replace the driver's attention and judgement. The driver always has the responsibility to ensure the car is being driven safely, at a suitable speed, maintaining a proper distance from other vehicles, and in line with the current traffic rules and regulations.
- Please keep the manual in a secure location, near the product for future reference.
2. General Warnings
Congratulations on your new XTRONS product. With over 19 years of expertise in In-Car Entertainment, XTRONS has been persistently striving to introduce the newest technology and concepts to your driving experience. Our aim is to create durable, high-quality products accompanied by superb customer service, leading the aftermarket in-car entertainment industry.
- The head unit is not a toy. Do not allow children to play with, on, or around the product. Close supervision of children is always necessary.
- Turn off this unit in locations where inflammable gas or strong magnetic fields are present (for example a petrol station) as it may cause an accident.
- Do not place heavy or dangerous objects on the screen.
- To avoid electric shock, fire, serious injury, or product damage, do not expose the product to humidity or splash water directly onto the product.
- If the unit has a CD/DVD drive, it can play 120mm (5 inch) discs only, please do not insert any discs of different sizes into the disc slot.
- To ensure safety, the wiring and installation of this unit requires technical skill and experience. If your car has airbags or any other shock-absorbing safety equipment, please contact the professional car electrician or dealer from whom you purchased this unit before installation.
- Under no circumstances will XTRONS be held responsible for any incidental, indirect or consequential damages or any other damages including, but not limited to, loss of profits, or personal injury.
- When navigating, carefully compare information displayed on the navigation system with all available navigation sources, including information from street signs, visual sightings, and maps. Always operate the vehicle in a safe manner. Ensure to not become distracted by the navigation system whilst driving. For safety, always resolve any issues or distractions before driving. XTRONS shall not be liable for problems or accidents resulting from failure to observe the driving conditions.
- XTRONS' navigation system can be utilised when the ignition key is turned to ON or ACC. To conserve the battery, it should be operated with the engine running whenever possible. Using the navigation system for an extended period with the engine switched off can lead to battery drainage.
3. Setup
3.1 Wiring Harness Diagram
Below are typical wiring harness diagrams for Double Din and Single Din units. Always refer to the specific diagram provided with your product for accurate connections.

Double Din RCA Connections:
- A: AMP-12V, AUX-R-IN, AUX-L-IN, RCA_SIM_DATA, RCA_SIM_DET, RCA_SIM_CLK, RCA SIM RST, RCA_SIM_VDD, FCCD-V, MIC-, GND, RCA-FL, RCA-FR, GND, GND, GND, NC, RCA_SUB, AUX-V-IN, MIC+
- B: TV-IR, TV-LIN, TV-RIN, TV-VIN, TV-ACC, TV-12V, NC, GND, GND, GND, GND, GND
- C: GND, RCA-RL, CAN-TX, NC, NC, RCA-RR, CAN-RX, NC
- D: USB-5V, GND, USB1-D+, USB1-D-
- E: DC-5V, GND, USB3-D-, USB2-D+, USB2-D-, USB3-D+
Double Din Power Connections (PWR):
- GND, B+, ACC, ILLUMI, BACK, SW-KEY2, SW-KEY1, ANT-12V, FR-, RL-, FR+, FL+, FL-, RR+, FL+, RR-
- Power Source: DC 12V, Max Consume Current: 10A
- Power Consumption: 4X45W
Single Din RCA Connections:
- A: AMP-12V, AUX-R-IN, AUX-L-IN, RCA SIM DATA, RCA_SIM_DET, RCA_SIM_CLK, RCA SIM RST, RCA_SIM_VDD, FCCD-V, MIC-, GND, RCA-FL, RCA-FR, GND, GND, GND, NC, RCA_SUB, AUX-V-IN, MIC+
- B: L-AUTO, GND, GND, R-AUTO, GND, F VIEW, 360-5V, R VIEW, REAR VIEW, 360-5V
- C: GND, RCA-RL, CAN-TX, NC, NC, RCA-RR, CAN-RX, NC
- D: USB-5V, GND, USB1-D+, USB1-D-
- E: DC-5V, GND, USB3-D-, USB2-D+, USB2-D-, USB3-D+
Single Din Power Connections (PWR):
- GND, B+, ACC, ILLUMI, BACK, SW-KEY2, SW-KEY1, ANT-12V, FR-, RL-, FR+, FL+, FL-, RR+, FL+, RR-
- Power Source: DC 12V, Max Consume Current: 10A
- Power Consumption: 4X45W
3.2 Basic Operations
3.2.1 Main Screen Introduction
The main screen of your XTRONS unit provides quick access to various functions. The layout typically includes:
- Top Bar: Icons for Home, Time, Volume, Screenshot, Screen Off, Recent Apps, Back, Navigation, Zlink, Bluetooth, Radio, Settings.
- Central Display: Shows current time, navigation speed (Km/h or mph), and active media (e.g., Music, Radio).
3.2.2 Touch Screen Gestures
The Android system allows operation via touchscreen. Common gestures include:
- Clicking: Tap an icon or option to select it.
- Dragging: Slide a finger across the screen or use scroll bars for navigation (e.g., browsing contact lists).
- Zooming: Pinch or spread two fingers on the screen to zoom in or out (available in certain apps like Chrome).
3.2.3 Change Launcher
To switch the user interface (UI) theme:
- Navigate to the "Theme" option in the Home Screen.
- Select one of the available theme options (e.g., THEME1, THEME2, THEME3, THEME4) and press "INSTALL".
Note: For devices with a rotating screen, only one UI set is available.
3.3 Internet Connectivity
3.3.1 Wi-Fi Connection
To use Wi-Fi internet:
- From the Home screen, tap "Settings" > "Network" > "More" > "Network & internet" > "Internet".
- Toggle Wi-Fi ON.
- In the list of available WLANs, click on the desired network. If it's encrypted, enter the password.
- Alternatively, scroll down and click "Add network" to manually enter network name and password.
Once connected, a Wi-Fi icon will appear in the status bar.
3.3.2 4G Network Connection
To use 4G internet, you need a 4G LTE USB Dongle (EE/CPT/4GDONG001 or EE/CPT/4GDONGUSA). Please note that the 4G function supports most frequencies in South and North America, Asia, Europe, the Middle East, and Australia, but some bands may not be supported.

SIM Card Installation:
- Turn the machine off.
- For Type A SIM slot: Find the SIM cable, push right to open the lid, push the clip up, insert the SIM card in the correct direction, close and push the clip down to lock, then close the lid and push left to lock.
- For Type B SIM slot: Find the SIM cable, push up to open the lid, push down and lift the clip to open, insert the SIM card in the correct direction, close and push the clip up to lock, then close the lid and press to lock.
- Check the signal mark in the upper right corner of the display. If normal, you can surf the internet.
Note: SIM card slot design may vary. SIM card is not included and accepts Micro-SIM card (15mm*12mm) ONLY. Do not plug or unplug the SIM card while the machine is running. Ensure correct SIM card direction to avoid damage.

3.4 USB Tethering
To set up USB Tethering with your phone:
3.4.1 For Android Devices
- Connect your Android mobile device to your XTRONS unit via USB cable.
- Open your phone's settings and go to "Network & Internet" > "Hotspot & Tethering".
- Enable "USB tethering".
Successful tethering is indicated by the appearance of the "< - >" icon on the XTRONS' status bar.
3.4.2 For iOS Devices
- Enable the iPhone network settings in the XTRONS unit: Go to "Settings" > "More" > "Factory Setting" > Input password: 0000 > "App" > Enable "USBMUXD".
- Go to your iPhone's on-screen Settings. Look for "Personal Hotspot". Tap on "Personal Hotspot" and then slide the switch to ON.
- Connect the iPhone to your XTRONS using a USB cable. If prompted "Do you want to trust this device?", tap "Trust".
- When the XTRONS device is connected to your iPhone, a blue band will appear in the status bar at the top of the iPhone screen.
4. Operating
4.1 Radio
To listen to the Radio, touch the Radio icon in the APPs menu.
- Radio Region Setting: If your radio is set to a different region/country, you can change it in: Settings > Radio > Radio area.
- Search Radio Manually: Touch the left or right arrow to change frequencies. Press the search icon to automatically find the nearest working frequency.
- Auto Search: Press the search icon for automatic search from low to high frequency. The radio app will find and save the strongest signals. Press the icon again to stop.
- Save Station: To manually save a station, find the desired frequency and press and hold a number button for 2 seconds. You can save up to 18 FM and 12 AM stations.
- AF (Alternative Frequencies): Automatically selects the best frequency for the set radio station (for FM radio).
- TP (Traffic Program) / TA (Traffic Announcement): TP finds stations broadcasting traffic bulletins. TA stops other media to play traffic announcements.
- PTY (Program Type): Scans for pre-defined program types like rock, news, jazz.
- Band: Choose between different FM and AM brands.
- Mono/Stereo: Switch between Mono and Stereo FM reception. Mono can improve reception for unstable signals. "ST" symbol indicates stereo.
- LOC (Local): Receive only close-range and local signals. Default is DX (foreign and local).
- Settings: Touch the gear icon to access settings for LOC, ST, AF, TA, and PTY.
4.2 Navigation
Press the Setting icon, select "Navi" to find the Navi Setting.
- Navi App Select: Choose your preferred navigation application.
- Automatic Entry Navigation: Unit can automatically enter navigation 3 seconds after startup.
- Navi Prompt Mode: Choose between sound mix and sound switch.
- Navigation Mix Ratio: Set the navigation mix ratio from -5 to 5 in mixing sound.
- Online Maps: Google Maps is preinstalled. Download online maps when connected to the internet.
- Offline Maps: Save specific areas from Google Maps or download 'HERE WE GO' offline maps from Google Play.
- Purchase GPS Maps Card: Install a CPS card with maps via SD card (if device has a slot).
4.3 Bluetooth
Press the BT icon to enter the Bluetooth menu.
- Device Name: Your unit's Bluetooth name (e.g., XTRONS).
- Pair Password: Default is 0000.
- Auto Answer: Automatically answers incoming calls.
- Auto Connect: Automatically connects to a previously paired device.
4.3.1 Bluetooth Connection
While driving, do not perform complicated operations such as dialing numbers or using the phone book. Stop your car in a safe place first.
- Turn on Bluetooth on your phone.
- Touch the name of the device you want to connect.
- Your phone will appear in the connected devices list.
- Use the fast switch icon (connect/disconnect) to manage connections.
4.3.2 Hands-Free
For your safety, do not use a mobile phone while driving, even if it's fully hands-free.
- Dial Pad: Use the on-screen dial pad to make calls.
- Make a Call: Tap the green phone icon.
- Delete: Tap the trash can icon to delete numbers.
- Microphone: Tap the microphone icon to turn it on/off.
4.3.3 Phone Book
- Make a Call: Tap the phone icon next to a contact.
- Delete Contact: Tap the trash can icon.
- Transfer Phone Book: Tap the sync icon to transfer contacts from your smartphone. Grant permission to access contacts.
Note: If the Phonebook contains more than 1000 entries, data may not transfer. Transfer may also depend on Bluetooth version or if it contains image data.
4.3.4 Call History
View answered, missed, and dialed calls. Options to dial a call, make a call, delete one entry, or delete all entries.
4.3.5 Bluetooth Music
Play music from your connected Bluetooth device. Controls include Previous, Play/Pause, and Forward.
Note: Using other phone functions during Bluetooth audio may cause noise. Audio may pause during Bluetooth pairing.
4.4 Split Screen
View two apps side by side on the same screen.
- Click the split screen icon from the status bar.
- Click the app icon you wish to use, and from the dropdown menu, choose "Split screen".
- Tap another app to use simultaneously.
Note: Split screen is not available on devices with 5-inch and 6.2-inch screens. Compatibility varies by application.
4.5 Multimedia
4.5.1 Music Audio
Play audio files from USB / SD. Insert a USB drive / SD card with music files and tap the music icon to open the player.
- Controls: Content list, Previous, Play/Pause, Next, Loop Mode.
4.5.2 Video Playback
Play video files from USB / SD. Insert a USB drive / SD card with video files and tap the video icon to open the player.
- Mini Player: Watch video in mini player mode.
- Screen Ratio: Change screen ratio (Center, Best Fit, Fit Horizontal/Vertical, Full Screen, 16:9, 4:3).
- Playback Modes: Random, File Repeat, Repeat All.
- Controls: Previous, Play/Pause, Next, Content list.
Note: Video playback while driving is prohibited. Factory settings prevent this. You can change this in Settings > Display > Brake. Not all devices have an SD card slot.
4.6 DSP (Digital Sound Processor)
Tap the DSP EQ icon to open the DSP setting menu.
4.6.1 Sound Effect
Select from Standard, Soft, Rock, Pop, Normal, Lobby, Cinema, Classical, Jazz, Custom1, Custom2, and Custom3.
4.6.2 EQ (Equalizer)
After choosing a sound effect, tap the EQ icon to set frequencies. Adjust sliders for 30Hz to 16000Hz.
4.6.3 Sound Stage Center
Adjust the sound field to gather in the center of the stage. Select a position (front left, front right, rear mode, center position) or drag the cross point. Only one position can be chosen as center.
4.6.4 Loudness
Set the boost level for low and high tones. Adjust Gain from 0dB to 12dB. Set FC (Frequency Cut) to off, 54Hz, 68Hz, 86Hz, 108Hz, 134Hz, 172Hz, or 214Hz.
4.7 Steering Wheel Control
To use this feature, you may need to adjust settings on the XTRONS unit. A special adapter (not included) might be required for your car.
Note: For vehicles with a digital steering wheel control system (CAN bus), this feature may not be available due to CAN bus protocol limitations.
Setup Steps:
- From the Home screen, go to "Settings" > "Steering wheel".
- Reset: Resets all settings before new setup.
- Save: Saves settings after new setup.
- Touch the desired function key on the screen, then press the same function button on the steering wheel. Repeat for all relevant functions.
4.8 CarAutoPlay / Android Auto
This head unit supports wireless CarPlay and wired/wireless Android Auto.
Please be aware that the system will automatically disable Bluetooth and Wi-Fi when using wireless CarPlay or Android Auto.
4.8.1 For iOS Devices (Wireless CarPlay)
- Go to Settings > Bluetooth, turn Bluetooth ON.
- Select the head unit's Bluetooth name, enter password 0000.
- When iPhone connects for the first time, click "Use CarPlay" in the dialog box.
- CarAutoPlay will load after 4-5 seconds.
Note: iPhone must have iOS 12.0 or above for wireless CarPlay.
4.8.2 For Android Devices (Wired Android Auto)
- Install the "Android Auto" APP on your Android Smartphone.
- Open CarAutoPlay, plug your Android Smartphone's USB cable into the unit. CarAutoPlay will automatically load.
4.8.3 For Android Devices (Wireless Android Auto)
- Turn on Bluetooth and Wi-Fi on your phone and Android Head Unit.
- Select the head unit's Bluetooth name, enter password 0000.
- Pair your phone's Bluetooth with the head unit. Wi-Fi will automatically connect the hotspot.
- Open the CarAutoPlay APP to load.
Note: Android smartphone must be able to install Google services, Google APPS and Android Auto application.
4.9 Gyroscope (Available on Specific Models)
The gyroscope provides vehicle orientation and tilt data, useful for off-road navigation.
- Reset Button: When parked on a flat surface, press Reset to calibrate.
- Settings: Customize display interface.
- Level Meter Direction: Change display direction for horizontal position.
- Incline Meter Direction: Adjust display direction for vertical angles.
4.10 Connect to Other External Devices
4.10.1 Audio/Video Input (CBVS signal compatible)
Connect an external device to the AV-IN input terminal. Select AV-IN as the source and start playing media on the connected device.
4.10.2 OBD02 (Dongle is optional)
Retrieve real-time information and error codes from your vehicle's computer using an OBD-II dongle.
Connection Guide:
- Plug the OBD dongle into your vehicle's OBD port.
- Tap to search for OBDII in Bluetooth mode of the XTRONS unit and pair.
- Tap the OBD app "Torque" icon in the main menu.
- Tap > Settings > OBD2 Adapter Settings, select connection type (Bluetooth, Wi-Fi, USB) and the OBD2 device.
Note: OBD2 dongle is optional and sold separately. No password needed. Connect by Bluetooth, USB, or Wi-Fi. OBD connector port location varies. Some OBD data may not be correctly read due to different ECU systems.
4.10.3 USB DAB (Dongle is optional)
To listen to DAB source, use the preinstalled DAB app when the DAB dongle is connected via USB. The DAB dongle must be Android-compatible.
4.10.4 DVR (Dash Cam, optional)
A DVR (e.g., ICE/SS/DVR025S) connected to the unit records your journey. Access files from the unit. Refer to the DVR Dashboard Camera instruction manual for details.


4.10.5 TPMS (Tyre Pressure Monitoring System, optional)
Use the TPMS app to view tyre pressure and temperature. Sensors automatically monitor and transmit real-time statistics. Only works with Android-compatible TPMS systems.
5. Settings
5.1 General
- Auto Play: Choose to automatically play music when inserting an SD card or USB storage device.
- Show Screenshot Button: Turn the screenshot button on or off.
- USB-TV Out: Enable/disable USB-TV out functionality. Auto Start option available.
- Size Setting: Fine-tune display dimensions.
- Colour Setting: Adjust colour settings.
- CANbus type classification selection: Click "Modify" to select CANbus company, car company, car model, and car configuration.
5.2 Display
- Night Brightness Control: Choose off, by headlight, or by time.
- Night Brightness: Adjust slider for night brightness.
- Panel Colour Setting: Set panel colour and mode.
- Panel Colour Power: Choose from by light, by ACC, by light and ACC, by power, and by light and power.
- Brake: Choose whether to receive a warning when playing video whilst driving. CAUTION: For safety, video images cannot be viewed while vehicle is in motion. Apply parking brake to view.
- Brightness: Adjust slider for screen brightness.
- Wallpaper: Choose from gallery, live wallpapers, or wallpapers.
- Exit Sleep Show Boot Logo: Display boot logo when exiting sleep mode.
5.3 Network
- Internet: Turn Wi-Fi on/off. Tap a listed network and enter password.
- Airplane Mode: Enable/disable.
- Hotspot & Tethering: Turn Wi-Fi hotspot on/off. Set up Wi-Fi hotspot.
- Data Saver: Enable/disable.
- VPN: Add VPN details, connect with username and password.
- Private DNS: Select Off, Automatic, or enter hostname.
- WiFi Switch: Turn Wi-Fi on/off. Choose a network and enter password.
5.4 Navi
- Navi App Select: Choose navigation application.
- Automatic Entry Navigation: Enter navigation automatically 3 seconds after starting up.
- Navi Prompt Mode: Choose between sound mix and sound switch.
- Navigation Mix Ratio: Set mix ratio from -5 to 5.
5.5 Reverse
- Mirror Rearview Camera Images: Normal (as captured) or Mirror (flipped horizontally).
- Mute during Backwards: Choose no delay, or delay from 1 to 10 seconds, or mute.
5.6 Sound
- Keypress Beep: Enable/disable beep tone when pressing keys.
- Power on Volume Limit: Set volume level when system powers on.
- Power on Volume: Adjust slider for power on volume.
- Power on BT Volume: Adjust slider for Bluetooth volume.
- Media Volume: Adjust slider for media volume.
5.7 Radio
- Radio Area: Choose preferred radio frequency range (e.g., Asia 1, Europe, USA 1).
- Radio Auto Antenna: Enable/disable auto antenna.
- RDS Enable: Toggle RDS functionality on/off.
- Power Off Memory: Save last radio settings when powered off.
5.8 Steering Wheel
Allows use of vehicle's steering wheel controls.
5.9 About
View device information: device name, model, CPU, memory, flash, Android version, IP address, Wi-Fi MAC address, Bluetooth MAC address, Bluetooth version, AUTH version, Android ID, MCU version, APP version, and LCD ARG.
5.10 More
- System Setting:
- Network & Internet: Detailed network connectivity options.
- Apps: View and manage recently accessed and installed applications.
- Storage: View storage space, free up space.
- Sound & Vibration: Media Volume, Live Caption, Default Notification Sound, Default Alarm Sound, Always Show Icon When in Vibrate Mode.
- Display: Brightness level, Screen Timeout (never, 15s, 30s, 1m, 3m, 5m, 10m), Dark Theme, Auto-rotate screen, Screen Saver, Wallpaper.
- System: Languages, Keyboard (On-screen keyboard, Spell checker, Personal dictionary, Pointer speed), Date & time, System Update, About Device.
- System Update: Options include restore factory, MCU update, CANbus update, app online upgrade, etc.
- Factory Setting: Enter password 0000 to access.
6. Troubleshooting
Q: The unit does not turn on.
- Reset the unit and reconnect.
- Check connections: ground (black), constant 12V (yellow), and accessory 12V (red) wires for correct voltage and good ground.
- Check if the fuse has blown.
- Check your vehicle wiring diagram for correct connections.
Q: Radio Auto searching does not stop.
A: Switch off AF & TA.
Q: Bluetooth pairing constantly connects and disconnects.
- Poor Bluetooth reception: Move phone closer to unit, remove obstacles.
- Some phones may connect/disconnect during calls; this is not a malfunction.
- Bluetooth connection may deactivate automatically as a power-saving feature on some phones; this is not a malfunction.
- Disconnect Wireless CarPlay or Wireless Android Auto.
- Remove all other paired Bluetooth devices from the XTRONS pairing list.
- If your phone has other saved Bluetooth devices, reset the connection and reconnect from scratch.
- Restart the XTRONS device and the Bluetooth device you want to connect.
Q: No sound?
A: Check speaker wire connections. Positive (+) terminal of speaker should connect to positive terminal of other components. Connect amplifier control wire (REM) from car to amplifier control wire (AMP wire) of XTRONS unit.
Q: SIM card cannot be detected. / No Internet connection.
- Check SIM card status.
- Check the signal status.
- Enable Mobile data.
- Check APN settings.
Q: GPS no signal / poor signal.
A: Check if the GPS antenna is connected properly. Mount the GPS antenna on the dash or rear deck, with a clear path to the sky, not too close to A-pillars or a 2-way antenna. Consider mounting externally if you have a wired rear defroster, metallic window tint, solar reflective window, or windscreen-mounted radio antenna.
Q: Touch screen not responding.
- Remove plastic touch screen protector sheet if too thick.
- Calibrate the touch screen (contact XTRONS support).
- Reset the unit.
Q: Radio reception is poor.
- Extend the car antenna fully.
- Check if vehicle has an active car antenna and if it needs phantom power.
- Check the radio region in unit settings.
- Try a different radio antenna.
Q: How to change the language on the unit?
A: Settings > More > System setting > System > Languages > System Languages.
Q: How to change the Date and Time?
A: Settings > More > System setting > System > Data & time.
Q: How to change the display wallpaper?
A: Press and hold any blank area of the lower screen area to access the wallpaper setting menu.
Q: How to change Speed Unit.
A: Press the speed unit from the Home screen to switch the unit.
Q: Reversing camera image is reversed.
A: Check settings and change the “mirrored” setting: Settings > Reverse > Mirror rearview camera images.
Q: Reversing camera has no video signal.
- If original reversing camera, contact XTRONS customer service with vehicle model and year.
- If aftermarket reversing:
- Ensure camera is properly connected to head unit. Check all wiring connections, especially reversing control wire and video input cable.
- Check video cable for damage.
- Verify standard of reversing camera.
- Inspect rear camera for integrity.
Q: Poor image quality of reversing cameras (Fuzzy, flashing, grainy, black and white static, etc).
- Check for dirt on the camera.
- Add a Power Filter Rec.
- Use a camera that supports your car's video system or use a converter.
Q: OBD fails to connect to ECU.
- Remove and re-plug OBD02, ensure it's fully seated.
- Reset unit, clear all phone connections in Bluetooth.
- Try OBD02 in a different car.
- Disconnect OBD2 dongle from phone before connecting to unit.
Q: Why can't third-party launchers be installed? / Why can't third-party launchers be permanently saved?
A: For devices with rotatable screens, third-party launchers are often not optimized for this functionality and may not be compatible or save permanently.
7. Specifications
| Attribute Name | Attribute Value |
|---|---|
| Brand Name | XTRONS |
| Item Type | Cables, Adapters & Sockets |
| Model Name | Accessories |
| IS It With PCB | No |
| High-concerned chemical | none |
| Origin | Mainland China |
| 1080P Camera Car DVR Video Recorder | ICE/SS/DVR025S |
| Universal Fit for Front view Camera | ICE/SS/CAM001F |
| 4G LTE Dongle FOR USA ONLY | EE/CPT/4GDONGUSA |
| Universal Car Rear Reverse Parking Camera | ICE/SS/CAMBMT004 |
| Universal Car Stereo FM Radio Antenna | EC/ARL/RANT01 |
| DSP Cable | ICE/ACS/BMWDSP01 |
| 4G LTE USB Dongle | EE/CPT/4GDONG001 |
| Optical Fiber Decoder Box for BMW E39 / E46 / E53 / E90 / E91 / E92 / E93 | AK/BMW01/FOBB05 |
| Wireless HDTV Cable Adapter | EE/ACS/HDTV05 |
| Radio Antenna Cable for BMW Vehicles | ICE/ACS/ANT001 |
| Car FM AM Radio Signal Amplifier | EC/ARL/RAMP02 |
| MOST Fibre Optic Loop Female Connector | ICE/ACS/Fiberloop |
| MOST Fibre Optic Extension Cable Male to Male | ICE/ACS/FEXL009 |
7.1 Accessory Details
Here are some specific details for the listed accessories:
- ICE/SS/CAM001F (Universal Fit Front View Camera): Wide Angle, Waterproof, Dustproof.
- ICE/SS/CAMBMT004 (Universal Car Rear Reverse Parking Camera): Specially designed for BMW Old 5 Series / 3 Series / X5. Features CMOS Camera, 160° Wide Angle Lens, Waterproof, Dust-proof.
- EC/ARL/RANT01 (Universal Car Stereo FM Radio Antenna):
- ICE/ACS/BMWDSP01 (DSP Cable):
- AK/BMW01/FOBB05 (Optical Fiber Decoder Box for BMW): Designed for BMW E39/E46/E53/E90/E91/E92/E93.
- EE/ACS/HDTV05 (Wireless Screen Mirroring Adapter): For Smart Phone to HD Monitor. Features 4K UHD Output, WiFi, Airplay, Miracast.
- ICE/ACS/ANT001 (Extra Long 6 Meters Radio Antenna Cable): Fit for BMW Vehicles. If your BMW vehicle's radio antenna port is in the car's trunk, you need to order this radio antenna extension cable to finish the installation.
- EC/ARL/RAMP02 (12V Car FM/AM Radio Signal Amplifier): Reception Booster with FAKRA II Connector. This item is used for increasing the signal reception; if the antenna reception is poor or there is no signal, it will not work.
- ICE/ACS/Fiberloop (MOST Fibre Optic Loop Female Connector): For use with BMW, VW, Audi, Porsche, Mercedes Media Systems. Used when retrofitting media orientated systems or to loop MOST ring due to faulty component. Features Female Connector, Plug & Play, Compact Design, Protective sleeving.
- ICE/ACS/FEXL009 (5m MOST Fibre Optic Extension Cable Male to Male): For use with BMW, VW, Audi, Porsche, Mercedes Media Systems. Used when retrofitting media orientated systems or to extend MOST cables. Features Male to Male Connector, Plug & Play, Compact Design, Protective sleeving.












8. User Tips
- Pre-Purchase Compatibility Check: Before purchasing any accessory, it is highly recommended to take a photo of your car's existing options or wiring and consult with XTRONS customer service to ensure full compatibility.
- Customer Service: XTRONS customer service representatives are known to be friendly and helpful. Do not hesitate to reach out for any installation or operational queries.
- Initial Setup: After installation, perform a system reset and check all connections to ensure optimal performance.
9. Warranty & Support
For more information, installation guides, and technical advice, please visit the official XTRONS websites and social media channels:
- Official Website: www.xtrons.com
- Community Forum: bbs.xtrons.com
- Facebook: https://www.facebook.com/xtrons/
- Facebook Group: https://www.facebook.com/groups/1037383397682256/
- Twitter: https://twitter.com/xtrons_ug
- YouTube: https://www.youtube.com/user/ourxtrons/
A user manual in PDF format is also available for download: User manual (PDF)
© XTRONS CORPORATION. All rights reserved.