Mestek DM100

Contents

Mestek DM100 Digital Multimeter User Manual

Model: DM100

Brand: Mestek

1. Introduction

The Mestek DM100 is a high-precision 10000-count digital multimeter designed for a wide range of electrical measurements in household and professional settings. It features True RMS, auto and manual ranging, and advanced safety features to ensure accurate and reliable operation. This manual provides detailed instructions for safe and effective use of your DM100 multimeter.

Mestek DM100 Digital Multimeter with test leads
Figure 1: Mestek DM100 Digital Multimeter with test leads.

2. Safety Information

WARNING: To avoid possible electric shock, fire, or personal injury, please read all safety information before you use the product.

  • Always ensure the multimeter is set to the correct function and range before making any measurements.
  • Do not exceed the maximum input values for any range.
  • Always disconnect power to the circuit under test before connecting or disconnecting test leads, especially when measuring current.
  • Use caution when working with voltages above 30V AC RMS, 42V peak, or 60V DC. These voltages pose a shock hazard.
  • Inspect test leads for damaged insulation or exposed metal. Replace if damaged.
  • Ensure the battery cover is closed and secured before operation.
  • The device features overload protection (less than 250V) and will display 'LUSE' with a buzzer alarm for wrong test lead insertion or 'FUSE' for a blown fuse. Always heed these warnings.

3. Product Features

The Mestek DM100 Digital Multimeter offers a comprehensive set of features for various electrical testing needs:

  • 10000 Counts Display: Provides high resolution and accuracy for measurements.
  • True RMS: Accurate measurement of AC voltage and current for non-sinusoidal waveforms (up to 1kHz).
  • High-Speed Sampling: Measures at 10 times per second for quick and responsive readings.
  • Auto and Manual Ranging: Automatically selects the appropriate range or allows manual selection for specific measurements (DM100C model supports both).
  • Non-Contact Voltage (NCV) Detection: Safely detects AC voltage without direct contact, with audible and visual alarms.
  • Live Wire Identification (LIVE): Helps identify live wires in a circuit.
  • Contact Temperature Measurement: (Available on DM100C model) Measures temperature using a dedicated probe.
  • Diode and Continuity Test: For checking diodes and circuit continuity.
  • Data Retention (HOLD): Freezes the current reading on the display.
  • Flashlight/LED Lighting: Built-in light for working in dimly lit areas.
  • Automatic Shut-down: Conserves battery life by powering off after a period of inactivity.
  • Smart Chip + Dual Fuse: Enhanced overload protection to prevent damage to the meter from misoperation.
  • Anti-drop Rubber Protective Sleeve: Provides durability and protection against accidental drops.
  • HD Digital Display Screen: Features a reverse display AV screen with analog bar and digital readings for clear data at a glance.
  • Low Battery Indicator: Alerts when battery replacement is needed.
Multiple advantages of the Mestek DM100 multimeter
Figure 2: Overview of the DM100's multiple advantages including high-speed measurement, fuse reminder, HD display, 10000 count, shell drop protection, NCV, pure copper leads, temperature/humidity, and LED lighting.

4. Components Overview

Familiarize yourself with the main components of your Mestek DM100 multimeter:

Mestek DM100 product information diagram
Figure 3: Diagram showing the various parts of the DM100 multimeter, including NCV non-contact voltage detection, indicator light, data retention, switch/select, soft leather case, current input, flashlight, reverse VA screen, lighting switch, variable frequency voltage, gear wheel, measurement input, and public (COM) terminal.
  • Display Screen: Shows measurement readings, units, and function indicators.
  • Function Rotary Switch: Used to select the desired measurement function (e.g., Voltage, Current, Resistance).
  • Input Jacks:
    • VΩHz: Input for voltage, resistance, frequency, capacitance, diode, and continuity measurements.
    • mA: Input for milliampere current measurements.
    • 10A: Input for high current (up to 10A) measurements.
    • COM: Common (negative) input for all measurements.
  • Buttons:
    • SEL: Selects sub-functions within a rotary switch position (e.g., AC/DC, Diode/Continuity, Temperature/Humidity display).
    • HOLD: Freezes the current display reading.
    • V.F.C: Variable Frequency Control (specific function, refer to advanced usage).
  • Flashlight: Located at the top of the meter, activated by a dedicated switch.
  • Test Lead Storage: The anti-drop rubber protective sleeve on the back provides storage for test pens.

5. Setup

5.1 Battery Installation

  1. Ensure the multimeter is turned off.
  2. Locate the battery compartment on the back of the device.
  3. Open the battery cover.
  4. Insert 2 AA batteries, observing the correct polarity (+/-).
  5. Close and secure the battery cover.

5.2 Test Lead Connection

The DM100 comes with safe test leads featuring 92 pure copper cores and double-layer insulated soft silicone injection molding for durability and safety.

Safe test lead construction
Figure 4: Illustration of the safe test lead construction with pure copper cores and double-layer insulation.
  1. Always connect the black test lead to the 'COM' (common) input jack.
  2. For most measurements (voltage, resistance, capacitance, frequency, diode, continuity), connect the red test lead to the 'VΩHz' input jack.
  3. For current measurements up to 600mA, connect the red test lead to the 'mA' input jack.
  4. For current measurements up to 10A, connect the red test lead to the '10A' input jack.
  5. Ensure test leads are fully inserted into the correct jacks. The multimeter will alarm if leads are inserted incorrectly for the selected function.

6. Operating Instructions

6.1 General Measurement Principles

Turn the rotary switch to the desired function. The DM100C model supports both auto and manual ranging. The DM100 model primarily uses manual ranging, requiring you to select the appropriate range for your measurement.

Auto and manual range selection on DM100C
Figure 5: The rotary switch highlighting automatic and manual range selections for different measurement types on the DM100C model.

6.2 Specific Measurement Modes

  • Voltage Measurement (AC/DC):
    Turn the rotary switch to V~ (AC Voltage) or V- (DC Voltage). Connect the test leads in parallel with the circuit or component to be measured.
  • Current Measurement (AC/DC):
    Turn the rotary switch to A~ (AC Current) or A- (DC Current). Connect the test leads in series with the circuit. Ensure the red lead is in the correct current input jack (mA or 10A).
  • Resistance Measurement:
    Turn the rotary switch to Ω. Connect the test leads across the component. Ensure the circuit is de-energized.
  • Capacitance Measurement:
    Turn the rotary switch to F. Connect the test leads across the capacitor. Ensure the capacitor is discharged before testing. The DM100 offers fast capacitance measurement, as shown in the video below.
  • Video 1: Demonstration of the DM100's fast capacitance measurement speed compared to another meter.
  • Frequency Measurement:
    Turn the rotary switch to Hz. Connect the test leads to the signal source.
  • Diode Test:
    Turn the rotary switch to the diode symbol. Connect the test leads across the diode.
  • Continuity Test:
    Turn the rotary switch to the buzzer symbol. Connect the test leads across the circuit. An audible beep indicates continuity.
  • NCV (Non-Contact Voltage) Detection:
    Turn the rotary switch to NCV. Hold the top of the multimeter near the suspected voltage source. The device will provide audible and visual alarms if AC voltage is detected.
  • Non-Contact Voltage Testing with DM100
    Figure 6: The DM100 performing Non-Contact Voltage (NCV) testing, indicating safe design with audial and visual alarms.
  • Live Wire Identification (LIVE):
    Turn the rotary switch to LIVE. Use the red test lead to touch the conductor. The display will indicate 'LIVE' if a live wire is detected.
  • Live Wire Identification with DM100
    Figure 7: The DM100 performing Live Wire Identification in a circuit breaker box.
  • Temperature Measurement (DM100C only):
    Turn the rotary switch to °C/°F. Connect the temperature probe (if included) to the appropriate input jacks.
  • Contact temperature measurement with DM100C
    Figure 8: The DM100C model performing contact temperature measurement using a probe.
  • Ambient Temperature/Humidity Display:
    When the rotary switch is set to voltage, current, resistance, or capacitance, the ambient temperature and humidity can be displayed. Tap the SEL button to switch between temperature and humidity display.
  • Ambient temperature and humidity display on DM100
    Figure 9: The DM100 display showing ambient temperature and humidity, with instructions to tap the SEL button to switch views.

6.3 Additional Functions

  • Data Hold (HOLD): Press the 'HOLD' button to freeze the current reading on the display. Press again to release.
  • Flashlight: Use the dedicated lighting switch to turn the high-intensity LED flashlight on or off for improved visibility in dark environments.
  • Bright LED lighting on DM100
    Figure 10: The DM100 with its bright LED lighting activated, useful for night use.
  • Automatic Shut-down: The multimeter will automatically power off after a period of inactivity to save battery life.

7. Maintenance

7.1 General Care

  • Keep the multimeter clean and dry. Use a soft, damp cloth for cleaning; do not use abrasives or solvents.
  • Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
  • The anti-drop rubber protective sleeve helps protect the device from impacts. Ensure it is properly fitted.

7.2 Battery Replacement

When the low battery indicator appears on the display, replace the batteries promptly to ensure accurate readings.

  1. Turn off the multimeter.
  2. Open the battery compartment cover on the back.
  3. Remove the old 2 AA batteries.
  4. Insert new 2 AA batteries, ensuring correct polarity.
  5. Close the battery compartment cover securely.

7.3 Fuse Replacement

The DM100 is equipped with dual fuses (600mA/10A) for overload protection. If the 'FUSE' alarm is displayed or a current measurement fails, the fuse may need replacement.

Smart chip and double fuse protection
Figure 11: Internal view showing the smart chip and dual fuses for overload protection.
  1. Turn off the multimeter and disconnect all test leads.
  2. Open the battery compartment cover.
  3. Carefully remove the old fuse(s).
  4. Replace with new fuses of the correct type and rating (600mA and 10A).
  5. Close the battery compartment cover securely.

8. Troubleshooting

  • Multimeter does not turn on or display is dim: Check battery installation and replace batteries if necessary.
  • Incorrect or erratic readings: Ensure the correct function and range are selected. Check test lead connections and ensure they are not damaged. Verify the circuit is de-energized for resistance/continuity tests.
  • 'LEAD' alarm: Indicates incorrect test lead insertion for the selected function. Re-insert leads into the correct jacks.
  • Wrong plug and fuse blown alarms
    Figure 12: The DM100 displaying 'LEAD' for incorrect test lead insertion and 'FUSE' for a blown fuse, indicating double protection against damage.
  • 'FUSE' alarm: Indicates a blown fuse, typically during current measurement. Replace the fuse as described in the Maintenance section.
  • No NCV detection: Ensure the NCV function is selected and the meter is held close enough to the AC voltage source.

9. Specifications

AttributeDM100DM100C
Operating ModeManual rangeAuto and manual range
Display Count10000 count
DC Voltage Range0~999.9mV/9.999V/99.99V/999.9V
AC Voltage Range0~999.9mV/9.999V/99.99V/750V
DC Current Range0~99.99uA/999.9mA/600mA/10.00A
AC Current Range0~99.99mA/600mA/10.00A
Resistance Range0~999.9ohm/9.999Kohm/99.99Kohm/999.9Kohm/9.999Mohm/99.99Mohm
Capacitance RangeNO0~99.99mF
Frequency RangeNO0~9.999MHz
Temperature ProbeNoHave
Temperature Range--20℃~1000℃ (-4℉~1832℉)
DiodeSupport
On-off BeepSupport
Screen DisplayVA reverse display screen
Ambient Temperature0℃~60℃
True Effective Value1kHz
V.F.CSupport
Fuse AlarmSupport
Wrong Plug AlarmSupport
Data RetentionHave
Flashlight LightingHave
Automatic Shut-downSupport
NCVSupport
LIVESupport
Input Resistance10MΩ
Overload Protectionless than 250V
Undervoltage WarningSupport
Battery2 AA batteries
Security LevelCAT IV 600V/CAT III 1000V
Size185*85*40mm
WeightAbout 500g
Technical specifications table for DM100 and DM100C
Figure 13: Detailed technical specifications comparing DM100 and DM100C models.

10. User Tips

No specific user tips were available from provided reviews or Q&A content.

11. Warranty & Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.