Cytron SHIELD-MDD10

Contents

Cytron SHIELD-MDD10 DC Motor Driver Shield for Arduino

User Manual

1. Introduction

The Cytron SHIELD-MDD10 is a high-power, 2-channel DC motor driver shield designed for use with Arduino boards. It enables control of two brushed DC motors or a single bipolar/unipolar stepper motor, operating within a voltage range of 7V to 30V. Featuring a discrete NMOS H-Bridge design, this motor driver can continuously supply up to 10 Amperes per channel without requiring an additional heatsink.

The shield integrates a buck regulator that provides a stable 5V output, capable of powering the Arduino mainboard directly, eliminating the need for a separate power supply for the Arduino. It also includes onboard test buttons and motor output LEDs for convenient functional testing.

For enhanced flexibility, the Arduino pins used for PWM and DIR inputs are configurable via jumpers, allowing adaptation to various application requirements where specific pins might already be in use.

Cytron SHIELD-MDD10 Motor Driver Shield

Figure 1: Overview of the Cytron SHIELD-MDD10 Motor Driver Shield.

SHIELD-MDD10 integrated into a mobile robot

Figure 2: The SHIELD-MDD10 controlling motors in a mobile robot application.

2. Features

  • Shield for Arduino form factor.
  • Bidirectional control for two brushed DC motors.
  • Control for one unipolar/bipolar stepper motor.
  • Operating Voltage: DC 7V to 30V.
  • Maximum Motor Current: 10A continuous, 30A peak per channel.
  • Integrated buck regulator to produce 5V output (500mA max) for Arduino power.
  • Onboard buttons for quick functional testing.
  • LED indicators for motor output state.
  • Selectable Arduino pins for PWM/DIR inputs via jumpers.
  • PWM/DIR inputs compatible with 1.8V, 3.3V, and 5V logic levels.
  • PWM frequency support up to 20kHz (output frequency matches input frequency).
  • Overcurrent protection with active current limiting.
  • Temperature protection.
  • Undervoltage shutdown.

Key features of SHIELD-MDD10: Arduino Shield, no jumpers, no extra power

Figure 3: Visual representation of key features including Arduino compatibility and simplified setup.

3. Specifications

Parameter Value
Operating Voltage DC 7V to 30V
Maximum Motor Current 10A continuous, 30A peak per channel
Buck Regulator Output 5V (500mA max)
PWM Frequency Up to 20kHz
Logic Compatibility 1.8V, 3.3V, 5V
Dimensions (L x W) 82.80mm x 59.18mm
Mounting Hole Diameter 3.0mm (x2)

SHIELD-MDD10 Interface Diagram with Dimensions

Figure 4: Detailed interface diagram showing pin labels and physical dimensions of the SHIELD-MDD10.

4. Setup

4.1 Physical Connection to Arduino

  1. Align the SHIELD-MDD10 with the header pins on your Arduino board.
  2. Gently press the shield onto the Arduino until it is fully seated. No additional jumpers are required for basic connection to the Arduino.
  3. The integrated buck regulator will power the Arduino, so no separate power supply is needed for the Arduino itself.

4.2 Power Supply Connection

  1. Connect your DC power supply (7V to 30V) to the power input terminals (V+ and V-) on the SHIELD-MDD10.
  2. Important: Ensure correct polarity. The power input does not have reverse-voltage protection. Connecting the battery in reverse polarity will damage the motor driver instantaneously.

4.3 Motor Connection

  1. Connect your brushed DC motors to the motor output terminals (MOTOR1 and MOTOR2). Each motor has two terminals (e.g., M1A, M1B for Motor 1).
  2. For stepper motors, refer to the specific wiring diagram for your stepper motor type (bipolar/unipolar) and connect to the appropriate terminals.

Wiring diagram for SHIELD-MDD10 with two DC motors and battery

Figure 5: Wiring diagram illustrating connections for two DC motors and a DC 7V-30V power source to the SHIELD-MDD10.

5. Operation

5.1 Control Inputs (PWM and DIR)

The SHIELD-MDD10 is controlled using Pulse Width Modulation (PWM) and Direction (DIR) signals from your Arduino. The specific Arduino pins for these inputs can be configured using the onboard jumpers if the default pins are already in use.

  • **PWM (Pulse Width Modulation):** Controls the speed of the motor. A higher duty cycle results in higher motor speed.
  • **DIR (Direction):** Controls the direction of the motor.

5.2 Motor Control Logic

The following table outlines the control logic for brushed DC motors:

PWMx DIRx Output A (MxA) Output B (MxB) Motor x
Low X (Don't Care) Low Low Brake
High Low High Low Forward*
High High Low High Backward*

*Actual motor direction depends on the motor connection. Swapping the connection (MA & MB) will reverse the direction.

5.3 Testing with Onboard Buttons and LEDs

The SHIELD-MDD10 includes test buttons and motor output LEDs for quick verification of motor driver functionality without needing to write code. Consult the board's silkscreen for button locations and corresponding motor outputs.

6. Protection Features

The SHIELD-MDD10 incorporates several protection mechanisms to ensure reliable and safe operation:

  • **Overcurrent Protection:** Prevents damage to the motor driver if the motor stalls or an oversized motor is connected. The motor current will be limited at a maximum threshold.
  • **Temperature Protection:** The maximum current limiting threshold is dynamically adjusted based on the board's temperature. Higher board temperatures result in a lower current limiting threshold, preventing MOSFET damage.
  • **Undervoltage Shutdown:** The driver will shut down if the input voltage drops below a safe operating level, protecting both the driver and connected components.

Multi-protection design icons: Over Current, Temperature, Undervoltage Protection

Figure 6: Icons representing the multi-protection design features of the SHIELD-MDD10.

7. Maintenance

The SHIELD-MDD10 is designed for robust operation and generally requires minimal maintenance. However, consider the following for optimal performance and longevity:

  • **Keep Clean:** Ensure the board is free from dust, debris, and moisture. Use a soft, dry brush or compressed air for cleaning.
  • **Environmental Conditions:** Operate the shield within its specified temperature and humidity ranges to prevent damage.
  • **Connections:** Periodically check all power and motor connections to ensure they are secure and free from corrosion.
  • **Heat Management:** While designed for continuous 10A without a heatsink, in enclosed spaces or high ambient temperatures, ensure adequate airflow to prevent the temperature protection from triggering frequently.

8. User Tips

  • **Start with Low Power:** When first testing a new motor setup, begin with a lower PWM duty cycle to ensure all connections are correct and the motor behaves as expected.
  • **Verify Motor Current:** Always ensure your motors' continuous and peak current requirements do not exceed the SHIELD-MDD10's capabilities (10A continuous, 30A peak per channel) to avoid triggering overcurrent protection or damaging the board.
  • **Jumper Configuration:** Take advantage of the configurable PWM/DIR pins. If you encounter conflicts with other Arduino shields or components, reconfigure the jumpers to use alternative pins.
  • **Reverse Polarity Caution:** Double-check your power supply connections every time. The lack of reverse-voltage protection means incorrect polarity will instantly damage the board.

9. Troubleshooting

  • **Motor Not Moving:**
    • Verify the power supply is connected correctly and within the 7V-30V range.
    • Check all motor connections for looseness or incorrect wiring.
    • Ensure your Arduino is sending appropriate PWM and DIR signals.
    • Check if the overcurrent or temperature protection has been triggered (the board might temporarily shut down or limit current).
    • Use the onboard test buttons to quickly check if the motor driver itself is functional.
  • **Motor Moving in Wrong Direction:**
    • Swap the two motor leads (MA and MB) for the affected motor.
    • Verify the DIR signal logic in your Arduino code matches the desired direction.
  • **Arduino Not Powering On:**
    • Ensure the main power supply to the SHIELD-MDD10 is active and within the specified voltage range.
    • Check the 5V output from the buck regulator on the SHIELD-MDD10.
  • **Intermittent Motor Operation:**
    • This could indicate the temperature protection or overcurrent protection is being triggered. Reduce motor load, improve ventilation, or check for short circuits.
    • Ensure stable power supply. Voltage drops under load can cause issues.

10. Warranty and Support

For detailed warranty information and technical support, please refer to the official Cytron Technologies website or contact your point of purchase. Ensure you have your product model (SHIELD-MDD10) and any relevant purchase details available when seeking support.

Disclaimer: For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.