1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the MACH3V2.1-L CNC Engraving Machine Breakout Board Adapter. This board is designed to process signals from a host computer's LPT port, interfacing with MACH3 CNC system software to control various peripheral machine dynamics. It is suitable for a wide range of CNC equipment, including engraving machines, lathes, plasma cutting machines, laser engraving machines, CNC milling machines, and machining centers, offering a cost-effective CNC system solution.
2. Product Overview
2.1 Features
- High-Speed Signal Processing: Utilizes a special high-speed chip for input/output (I/O) signal processing, ensuring stable machine operation by correcting, enlarging, and filtering out disturbance signals.
- Isolated Power Supply: The computer's LPT port power supply is isolated from other parts of the board, enhancing data security and system stability.
- 5 Optically Isolated Input Signals: Communicates with the host computer via 5 input signals, isolated by optical coupling. P11 and P12 are high-speed inputs suitable for main shaft encoders or hand wheel A/B signals.
- Power Output Interfaces: Includes 12V-OUT and 5V-OUT power outputs for necessary components like Hall sensor switches and proximity switches.
- Configurable Input Ports: The 5 input ports can be configured for functions such as limit switches, origin, tool setter, start, stop, spindle speed input, or MPG input.
- 12 Output Signals: Supports control output for up to 6-axis linkage. Some output ports have reusable functionality, but each port can only be used for one function at a time.
- 3 Programmable Relays: Features P2, P3, and P4 relays controllable via MACH3 software programming. Each relay has an indicating lamp for intuitive status monitoring. These relays can control liquid coolant, mist coolant, or electromagnetic valve devices. P2 is typically for the spindle, P3 for cooling liquid, and P4 is user-definable.
- Spindle Speed Control: High-speed optical coupling isolation controls spindle rotational speed. Parallel port P1 outputs a PWM signal (up to 2.5KHz). A built-in D/A circuit converts PWM to a 0-10V analog output, compatible with inverters that support analog speed control. Note: PWM output and 0-10V output cannot be used simultaneously.
- Stepper/Servo Drive Compatibility: Can connect to stepper drives or servo drives (if they support digital signals) with a 5V output level.
- Wide Input Voltage: Operates with a 15-32VDC power supply, featuring reverse connection protection.
- Dual Output Voltages: Provides 5V and 12V output voltages with a 100mA output capacity.
2.2 Package Contents
- 1 x MACH3V2.1-L Breakout Board
2.3 Visual Guide




3. Specifications
| Feature | Description |
|---|---|
| Model | MACH3V2.1-L |
| USB Interface | Type B |
| Dimensions (L*W*H) | 11 cm * 7.5 cm * 2.4 cm (4.3 in * 2.95 in * 0.9 in) |
| Input Voltage | 15-32VDC (with reverse connection protection) |
| Output Voltage (Capacity) | 5V and 12V (100mA capacity) |
| Input Ports (5 total) | P10 (Emergency Stop), P11 (Reserved), P12 (Reserved), P13 (3-axis Limit), P15 (Reserved) |
| Output Ports (11 total) | P4 (X Pulse), P5 (X Direction), P6 (Y Pulse), P7 (Y Direction), P8 (Z Pulse), P9 (Z Direction), P16 (4th Axis Pulse), P17 (4th Axis Direction), P2 (Relay Port), P3 (Relay Port), P14 (Charge Pump) |
| Relays | 3 (P2, P3, P4) with indicating lamps, programmable via MACH3 |
| Spindle Speed Control | PWM output (P1, up to 2.5KHz) or 0-10V analog output (via D/A circuit) |
| Compatibility | MACH3 CNC system software, Stepper/Servo drives (5V level output) |
4. Setup Instructions
Before connecting, ensure all power is off. Refer to Figure 5 for a detailed connection diagram. Proper wiring is crucial for safe and correct operation.

4.1 Power Supply Connection
- Connect a 15-32VDC power supply to the designated 'power supply +' and 'power supply -' terminals. Ensure correct polarity to utilize the reverse connection protection feature.
- The board provides 5V and 12V output terminals for powering external sensors or components.
4.2 LPT Port Connection
- Connect the DB25 parallel port connector on the breakout board to the LPT port of your host computer.
4.3 Input Signal Connections
The board has 5 input signal terminals (P10, P11, P12, P13, P15). These are optically isolated for noise immunity.
- Emergency Stop (P10): Connect your emergency stop button to P10.
- Limit Switches (P13): Connect limit switches for 3 axes to P13.
- High-Speed Inputs (P11, P12): These can be used for connecting a main shaft encoder or other high-demand signals like hand wheel A/B.
- Configurable Inputs: The input ports can be configured within MACH3 software for functions such as origin, tool setter, start, stop, spindle speed input, or MPG input.
- Common Negative Terminal: For common negative (GND) connections, use the designated GND terminals.
4.4 Output Signal Connections (Stepper/Servo Drives)
The board provides 11 output signal terminals for controlling stepper or servo drives. The output level is 5V.
- X-axis: P4 (Pulse), P5 (Direction)
- Y-axis: P6 (Pulse), P7 (Direction)
- Z-axis: P8 (Pulse), P9 (Direction)
- 4th Axis: P16 (Pulse), P17 (Direction)
- Connect the pulse and direction signals from the breakout board to the corresponding inputs on your stepper or servo motor drivers.
4.5 Relay Connections
The board features three relays (P2, P3, P4) for controlling external devices.
- P2 Relay: Typically used for spindle control (e.g., ON/OFF).
- P3 Relay: Typically used for cooling liquid control (e.g., coolant pump ON/OFF).
- P4 Relay: User-definable, can be used for mist coolant, electromagnetic valves, or other auxiliary functions.
- Connect the devices to be controlled by the relays to the respective relay terminals. Each relay has an indicating lamp to show its status.
4.6 Spindle Speed Control Connection
The board offers two options for spindle speed control:
- PWM Output (P1): Connect P1 to an inverter that accepts PWM signals for speed control. The PWM signal is within 2.5KHz.
- 0-10V Analog Output: Use the 0-10V output terminals to control inverters that require an analog voltage signal for speed control.
- Important: Only one of these spindle speed control methods (PWM or 0-10V) can be used at a time. Do not connect both simultaneously.
4.7 Charge Pump Jumper (P14)
- The P14 terminal can be configured as a charge pump function. Refer to the diagram for the jumper settings (ON: PUMP-P14-ON, Cancel: PUMP-CANCEL).
5. Operating Instructions
This breakout board is designed to work seamlessly with MACH3 CNC system software. After completing the physical connections, configure MACH3 according to your specific machine setup.
5.1 MACH3 Software Configuration
- Install MACH3 CNC software on your host computer.
- Open MACH3 and navigate to the 'Config' menu, then 'Ports and Pins'.
- Configure the 'Motor Outputs' tab to assign the correct LPT port pins (P4-P9, P16-P17) for pulse and direction signals for each axis.
- In the 'Input Signals' tab, enable and assign the pins for emergency stop (P10), limit switches (P13), and any other configured inputs (P11, P12, P15).
- In the 'Output Signals' tab, configure the relay pins (P2, P3, P4) for spindle control, coolant, and auxiliary functions as needed.
- For spindle speed control, configure the 'Spindle Setup' tab. If using PWM, select the appropriate PWM output pin (P1) and set the base frequency. If using 0-10V analog, ensure the D/A circuit is enabled and configured correctly.
- Save your MACH3 configuration.
5.2 Basic Operation
- Power on the breakout board (15-32VDC).
- Launch MACH3 software on your computer.
- Ensure all emergency stops are disengaged and limit switches are not triggered.
- Test axis movement using MACH3's jogging controls.
- Test relay functions (spindle, coolant) through MACH3's M-codes or manual controls.
- Verify spindle speed control functionality.
- Load your G-code program and begin machining operations.
6. Maintenance
To ensure the longevity and reliable performance of your MACH3V2.1-L breakout board, follow these maintenance guidelines:
- Keep Clean: Regularly clean the board to prevent dust and debris accumulation, which can lead to overheating or short circuits. Use a soft, dry brush or compressed air.
- Environmental Conditions: Operate the board in a clean, dry environment, free from excessive moisture, extreme temperatures, and corrosive substances.
- Secure Connections: Periodically check all terminal connections to ensure they are tight and secure. Loose connections can cause intermittent operation or damage.
- Power Off Before Handling: Always disconnect power to the board and any connected components before performing any maintenance or making wiring changes.
- Visual Inspection: Inspect the board for any signs of physical damage, burnt components, or bulging capacitors. If any damage is found, discontinue use and seek professional assistance.
7. Troubleshooting
If you encounter issues with your breakout board, refer to the following common troubleshooting steps:
7.1 No Power / Board Not Responding
- Check Power Supply: Ensure the 15-32VDC power supply is correctly connected and providing the specified voltage. Verify polarity.
- Power Indicator: Check if any power indicator LEDs on the board are lit.
- Connections: Ensure all power connections are secure.
7.2 Motors Not Moving / Incorrect Movement
- MACH3 Configuration: Double-check your 'Ports and Pins' settings in MACH3 for motor outputs (pulse and direction pins).
- Driver Connections: Verify that the pulse and direction signals from the breakout board are correctly wired to your stepper/servo drivers.
- Driver Power: Ensure your motor drivers are powered correctly and enabled.
- Emergency Stop/Limits: Check if an emergency stop is active or if a limit switch is triggered, preventing movement.
- Motor Wiring: Confirm motor wiring to drivers is correct.
7.3 Relays Not Activating
- MACH3 Configuration: Verify the 'Output Signals' configuration in MACH3 for the relay pins (P2, P3, P4).
- M-Codes: Ensure you are using the correct M-codes or manual controls in MACH3 to activate the relays.
- External Device: Check the external device connected to the relay (e.g., coolant pump) for proper functionality and power.
- Relay Indicator: Observe the relay's indicating lamp. If it lights up but the device doesn't activate, the issue might be with the external device or its wiring.
7.4 Spindle Speed Control Issues
- MACH3 Configuration: Review the 'Spindle Setup' in MACH3.
- PWM/0-10V Selection: Ensure only one method (PWM or 0-10V) is connected and configured.
- Inverter Settings: Check your inverter's settings to ensure it's configured to accept PWM or 0-10V input for speed control.
- Wiring: Verify the wiring between the breakout board and the inverter.
8. User Tips
- Grounding: Proper grounding of your CNC machine and all electronic components is essential to minimize electrical noise and ensure stable operation.
- Cable Management: Use shielded cables for signal lines, especially for pulse and direction, to prevent interference. Keep power and signal cables separated where possible.
- Software Backup: Regularly back up your MACH3 configuration files and G-code programs.
- Start Simple: When setting up for the first time, test one axis at a time before attempting multi-axis movements.
- Documentation: Keep a record of your MACH3 settings and wiring diagrams for future reference or troubleshooting.
9. Warranty and Support
This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.