1. Introduction
This manual provides comprehensive instructions for the JIKONG V19 4.3-inch Smart Touch Screen Display. This display is designed to perfectly integrate with JIKONG V19 Energy Storage BMS (Battery Management System) units, offering a clear and convenient interface for monitoring and managing your battery system. Please read this manual carefully before installation and operation to ensure safe and efficient use of the product.

2. Safety Information
Always observe the following safety precautions to prevent injury or damage to the product:
- Ensure the power supply voltage is within the specified range (9-36V).
- Do not expose the display to extreme temperatures or humidity outside the operating limits.
- Avoid physical impact or dropping the device.
- Do not attempt to disassemble or repair the display yourself. Contact qualified personnel for service.
- Ensure all connections are secure and correct before powering on the system.
- This display is intended for use with JIKONG V19 BMS systems only.
3. Package Contents
Verify that all items are present in the package:
- 1 x JIKONG V19 4.3-inch Smart Touch Screen Display
- 1 x Display Cable (0.5 meters, customizable length)
4. Product Features
- Wide Power Supply Range: Supports 9-36V DC input (default).
- Comprehensive Display Content: Shows battery total voltage, battery power, and single series voltage.
- TTL Level Support: Default baud rate of 115200bps.
- Multi-language Support: Chinese, English, Thai, and Vietnamese options.
- Customizable Interface: Allows for language, logo, and general interface customization.
- Display Type: TFT LCD.
- High Resolution: 480*272 pixels on a 4.3-inch screen.
- Active Balanced BMS: Features active balancing for optimal battery health.
- Multiple Protections: Includes overcharge, over-discharge, overcurrent, and short circuit protection.
5. Specifications
| Parameter | Specification |
|---|---|
| Brand Name | JIKONG |
| Model | V19 4.3 Inch Smart Touch Screen Display (LCD-4.3-TTL-P) |
| Type | LIFEPO4 Battery BMS Display |
| Handware or Smart | SMART BMS |
| Balance Function | Active Balanced BMS |
| Charging Current | 300A (BMS dependent) |
| Charge and Discharge Port | Common Port BMS |
| Function | Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection |
| Usage Scenario | Power BMS, Energy Storage BMS, 3C Digital BMS |
| Certification | CE |
| Display Category | TFT |
| Display Size | 4.3 inch |
| Resolution | 480*272 |
| Backlight Type/Brightness | LED/300nit |
| Viewing Angle L/R/U/D | 85°/85°/85°/85° |
| Supply Voltage (with reverse protection) | 9V (Min) to 36V (Max) |
| Power Dissipation | 1.32W (12V@110mA) |
| Operating Temperature | -20°C to +70°C |
| Storage Temperature | -30°C to +80°C |
| Operating Humidity | 10% to 90% RH (at 25°C) |
| Standard Cable Length | 0.5 meters (customizable) |
6. Setup Instructions
6.1. Connecting the Display to the BMS
The JIKONG V19 4.3-inch Touch Screen Display connects to the JIKONG V19 PB Serial BMS via a UART connector. Ensure the BMS is powered off before making any connections.

6.2. External Interfaces and Pin Definitions
The display features two main external interfaces:
- User Interface: Uses a HY2.0mm-6P vertical stick socket for power supply and serial port signal connection.
- Key Extension Interface: Uses an A1254WF-6A vertical sticker socket to control BMS startup and shutdown.

Pin Definitions for HY2.0mm-6P Vertical Mount:
| Number | Name | Definition |
|---|---|---|
| 1 | K- | Activation signal negative electrode |
| 2 | K+ | Activation signal positive electrode |
| 3 | GND | Negative terminal (Power) |
| 4 | TTL-RX | UART RX, 5V |
| 5 | TTL-TX | UART TX, 5V |
| 6 | VCC | Display power output |
6.3. APP Configuration
To ensure proper communication between the display and the BMS, configure the JIKONG BMS APP:
- Open the JIKONG BMS APP.
- Navigate to the "Parameter Setting" page.
- Change the "Serial port 3 protocol" to "015-JK BMS PBxx SERIES LCD Protocol V1.0".

7. Operating Instructions
The 4.3-inch touch screen display provides a clear and convenient interface for monitoring your battery system. Navigation is typically done via touch input.

7.1. Battery Group Interface
This interface displays real-time information about the entire battery string:
- Current total voltage (Vtg.)
- Current (Cur.)
- Battery capacity (Bat-Capacity) and remaining capacity (Rem-Capacity)
- Maximum and minimum cell voltages (Max.Cell, Min.Cell)
- Temperature (Temp)
- Power (Pwr)
- Alarm status (Alarm)
- Charge (CHG) and Discharge (DCH) status
- Number of online battery packs (Packs)

7.2. Battery Pack Interface (Parallel Mode)
In parallel mode, you can select individual battery packs to view detailed information. The display can show the status of up to 16 battery packs, including:
- Design capacity and remaining capacity for each pack.
- Charge and discharge status of each pack.
- Individual cell voltages within the selected pack.

7.3. Protocol Selection Interface
This interface allows you to select the appropriate RS485 and CAN communication protocols for your specific setup. This ensures compatibility and proper data exchange with other devices in your system.

7.4. Product Overview Video
8. Maintenance
- Cleaning: Use a soft, dry cloth to clean the display screen. Avoid abrasive cleaners or solvents that could damage the screen surface.
- Storage: If storing the display for an extended period, ensure it is kept within the specified storage temperature and humidity ranges.
- Inspection: Periodically check the display cable and connectors for any signs of wear or damage.
9. Troubleshooting
- Display not turning on: Check the power supply connection and ensure the voltage is within the 9-36V range. Verify the display cable is securely connected to both the display and the BMS.
- No data displayed: Confirm that the BMS is powered on and functioning correctly. Check the APP configuration to ensure the correct serial port protocol is selected (015-JK BMS PBxx SERIES LCD Protocol V1.0).
- Incorrect readings: Ensure all BMS cell voltage wires are correctly connected and balanced.
- Touch screen unresponsive: Gently clean the screen surface. If the issue persists, power cycle the device.
10. User Tips
- The display is a screen module without a case. Consider appropriate housing or mounting for protection in your application.
- Ensure the supplied cable is used for connection to the JIKONG BMS for proper functionality.
- Always double-check connections before powering on to prevent damage.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
12. Frequently Asked Questions (FAQ)
- Q: Is this display compatible with other BMS brands?
- A: No, this display is specifically designed to be perfectly matched with JIKONG V19 Energy Storage BMS units.
- Q: What is the maximum number of battery packs it can monitor in parallel mode?
- A: The display can show the status of up to 16 battery packs in parallel mode.
- Q: Can I change the display language?
- A: Yes, the display supports Chinese, English, Thai, and Vietnamese languages, which can be switched via the interface.
- Q: What should I do if the screen is blank?
- A: First, check the power supply to the display and the BMS. Ensure all cables are securely connected. Then, verify the APP protocol settings as described in the setup section.