Douk Audio P7

Contents

Douk Audio P7 HiFi Phono Stage Tube Preamp

User Manual

1. Introduction

The Douk Audio P7 is a versatile HiFi phono stage and tube preamplifier designed to enhance your audio experience. It features both MM Phono and RCA inputs, allowing connection to turntables, phones, TVs, and CD players. With a true balanced XLR output, it ensures pristine audio quality by reducing noise and improving dynamic range. The P7 incorporates a high-pass filter for clearer vinyl playback and utilizes PSVANE ECC83 tubes for warm, rich sound. Precise tone controls with a bypass option allow for customized sound profiles or pure, unaltered audio.

2. Features

  • MM Phono/RCA Input Flexibility: Functions as both a phono preamp and tube preamp, compatible with turntables, phones, TVs, and CD players. Enhances sound clarity with a warm tone.
  • XLR Output for Pristine Audio: Offers true balanced XLR output in addition to standard RCA, reducing noise and improving dynamic range for crystal-clear, immersive sound with a wider soundstage.
  • Clearer Vinyl Playback with HPF: Integrated high-pass filter (active only in phono input mode) cuts subsonic noise below 20Hz, reducing distortion and rumble for cleaner playback.
  • True Tube Amplification: Powered by brand-new PSVANE ECC83 tubes, driven at 180V, delivering warmth and rich harmonic depth. Tubes are swappable for sound customization.
  • Precise Tone Control with Bypass: Fine-tune bass and treble (±6dB range) or engage bypass mode for a pure, unaltered signal path.

3. Package Contents

Please check the package for the following items:

  • 1* P7 Preamp
  • 2* PSVANE ECC83 Tubes
  • 1* DC 12V Power Adapter
  • 1* User Manual
Douk Audio P7 packing list showing the preamp, tubes, power adapter, and user manual.
Figure 3.1: P7 Preamp and included accessories.

4. Setup

Follow these steps to set up your Douk Audio P7 preamplifier:

  1. Tube Installation: Carefully insert the two PSVANE ECC83 tubes into their respective sockets on the top of the P7 preamp. Ensure they are seated firmly but do not force them.
  2. Power Connection: Connect the DC 12V power adapter to the 'DC 12V IN' port on the rear panel of the P7. Plug the adapter into a suitable power outlet. Ensure the power supply meets the DC 12V/≥2A requirement.
  3. Input Connection:
    • For Turntables (MM Phono): Connect your turntable's RCA output cables to the 'PHONO' RCA inputs on the rear panel. Connect the turntable's ground wire to the 'GND' terminal on the P7. If your turntable has a built-in phono preamp, use the standard 'RCA' inputs instead to avoid signal issues.
    • For Other Audio Sources (RCA): Connect devices like CD players, phones, or TVs to the 'RCA' inputs on the rear panel using RCA cables.
  4. Output Connection:
    • To Amplifier/Active Speakers (RCA): Connect the 'RCA' outputs on the rear panel of the P7 to the RCA inputs of your amplifier or active speakers.
    • To Amplifier/Active Speakers (XLR): For a balanced connection, use XLR cables to connect the 'XLR' outputs on the rear panel of the P7 to the XLR inputs of your amplifier or active speakers.
Diagram showing the front panel controls and rear panel input/output connections of the Douk Audio P7 preamp.
Figure 4.1: Front and Rear Panel Overview with Connection Points.

5. Operation

Once the P7 is set up, follow these instructions for operation:

  1. Power On/Off: Use the 'OFF' switch on the front panel to power the unit on or off. The power indicator will illuminate when on.
  2. Input Selection: Use the 'PHONO / RCA' switch on the front panel to select between your turntable (PHONO) or other audio sources (RCA).
  3. Volume Control: Adjust the 'VOLUME' knob on the front panel to control the overall output level.
  4. Tone Control:
    • Use the 'BASS' and 'TREBLE' knobs to fine-tune the low and high frequencies to your preference.
    • To bypass the tone control circuit for a pure, unaltered signal, set the 'TONE / BYPASS' switch to 'BYPASS'.
  5. High-Pass Filter (HPF):
    • The 'HPF/20Hz' switch on the rear panel is only active when 'PHONO' input is selected.
    • Set the switch to 'HPF/20Hz' to activate the high-pass filter, which removes subsonic noise below 20Hz.
    • Set the switch to 'FLAT' to deactivate the high-pass filter.
Image showing the Douk Audio P7 preamp with its bass, treble, and volume knobs, and a tone/bypass switch.
Figure 5.1: Tone Control and Bypass Functionality.
Close-up of the High-pass filter switch on the Douk Audio P7, showing HPF/20Hz and FLAT settings.
Figure 5.2: High-Pass Filter Switch.

6. Maintenance

Proper maintenance ensures the longevity and optimal performance of your P7 preamp.

  • Cleaning: Use a soft, dry cloth to clean the exterior of the unit. Avoid using liquid cleaners or solvents.
  • Tube Replacement (Tube Rolling):
    • The P7 supports swapping for PSVANE 12AX7-S, Shuguang 12AX7B, 7025, or 12AX7 tubes.
    • Always power off the unit and disconnect it from the power supply before replacing tubes. Allow tubes to cool down before handling.
    • Gently pull the old tubes straight up from their sockets. Align the pins of the new tubes with the socket holes and push them gently but firmly into place.
  • Op-Amp Replacement (Op-Amp Rolling):
    • The P7 features 3 pluggable NE5532 op-amps, which can be replaced with other dual op-amps such as 2604, 2134, or MUSES02.
    • High voltage is present inside the unit. Ensure the unit is powered off and disconnected from the power supply before attempting to replace op-amps.
    • Carefully remove the existing op-amps using an IC extractor tool. Ensure the new op-amps are correctly oriented (pin 1 alignment) and properly installed before powering on the unit. Improper installation can cause damage.
Close-up of two PSVANE ECC83 vacuum tubes.
Figure 6.1: PSVANE ECC83 Tubes for replacement.

7. Troubleshooting

Q: What is the input voltage of the P7?
A: The P7 operates at DC 12V/≥2A. Using over voltage can cause damage, while insufficient current may affect normal operation.
Q: Can I connect a turntable directly to the P7?
A: Before connecting, please check if your turntable has a built-in phono preamp. If so, use the RCA input to avoid unwanted noise. Only use the PHONO input if your turntable does NOT have a built-in preamp.
Q: Can the RCA and XLR outputs be used at the same time?
A: Yes, both RCA and XLR outputs can be used simultaneously. Their volume and tone are controlled together.
Q: Is the high-pass filter active in RCA input mode?
A: No. The high-pass filter is only available in phono input mode.
Q: Can I swap op-amps in the P7?
A: Yes, the P7 features 3 pluggable NE5532 op-amps, which can be replaced with other dual op-amps such as 2604, 2134, or MUSES02. Due to high voltage inside, please make sure the op-amp is properly installed before powering on. Always power off and disconnect the unit before attempting replacement.
Q: Can I replace the tubes in the P7?
A: Yes, the P7 supports swapping for PSVANE 12AX7-S, Shuguang 12AX7B, 7025, or 12AX7 tubes. Please replace tubes only when the unit is powered off and disconnected from the power supply.

8. Specifications

Parameter Value
Brand Douk Audio
Model P7
Audio Input MM Phono / RCA
Audio Output RCA / XLR
Input Sensitivity (Phono) 5mV
Input Sensitivity (RCA) 0.775V
Rated Output Level (Phono to RCA) 0.5V
Rated Output Level (Phono to XLR) 1V
Rated Output Level (RCA to RCA) 2V
Rated Output Level (RCA to XLR) 4V
THD+N (RCA Input) 0.1%
THD+N (Phono Input) 0.03%
SNR (RCA Input) ≥109dB
SNR (Phono Input) ≥82dB
Frequency Response (RCA Input) 20Hz-20KHz (±0.8dB)
Frequency Response (Phono Input) Conforms to RIAA characteristics
Treble/Bass Range ±6dB
High-Pass Filter Cut-off Frequency 20Hz
Input Voltage DC 12V≥2A (5.5*2.1mm)
Dimensions (W*D*H) 155*124*42mm / 6.10*4.88*1.65in
Net Weight 707g / 1.56lb
Package Weight 1.10kg / 2.43lb

9. User Tips

  • Experiment with Tube Rolling: The swappable PSVANE ECC83 tubes allow for customization of your sound. Try different compatible tubes (e.g., 12AX7-S, Shuguang 12AX7B, 7025, 12AX7) to find the sonic signature that best suits your preferences. Remember to power off the unit before swapping.
  • Op-Amp Customization: For advanced users, the pluggable NE5532 op-amps can be replaced with other dual op-amps like 2604, 2134, or MUSES02 to further tailor the sound. Exercise caution and ensure correct installation due to high internal voltage.
  • Optimal Power Supply: Always use a DC 12V power adapter with at least 2A output. An insufficient current supply can lead to operational issues.
  • Turntable Preamp Check: If your turntable has a built-in phono preamp, connect it to the P7's standard RCA input, not the PHONO input, to prevent signal overload and unwanted noise.
  • Utilize Balanced Outputs: For the best signal integrity and noise reduction, use the XLR outputs when connecting to compatible amplifiers or active speakers.

10. Warranty and Support

The Douk Audio P7 HiFi Phono Stage Tube Preamp comes with a 2-year warranty, as indicated by the product imagery. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the Douk Audio customer service directly. Refer to the contact information provided at the point of purchase for the most efficient support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.