BAJETON BJ7700

Contents

BAJETON BJ7700 Multi-Band Walkie Talkie User Manual

Model: BJ7700

Brand: BAJETON

1. Introduction

Disclaimer

This manual has been compiled with the aim of ensuring the accuracy and completeness of its contents. However, our company assumes no responsibility for any errors or omissions that may occur. Due to continuous technological development, our company reserves the right to change product design and specifications without prior notice. This manual may not be reproduced, modified, translated, or distributed in any form without prior written authorization from our company. Third-party products and content mentioned in this manual are the property of their respective owners, and our company makes no guarantee as to their accuracy, validity, timeliness, legality, or completeness.

RF Radiation Information

This product is intended solely for professional use where RF energy radiation requirements can be met. Users must be fully aware of RF radiation hazards and take appropriate measures to comply with RF radiation limits.

RF Radiation Basics

RF (Radio Frequency) refers to electromagnetic frequencies that can radiate into space. It is a technology widely used in fields such as communications, medical, and food processing, and it generates a certain amount of RF radiation during use.

FCC Regulatory Requirements

In accordance with the regulations of the Federal Communications Commission (FCC) of the United States, this product must comply with FCC RF radiation limits to be sold in the U.S. market. Manufacturers are required to inform users of important safety precautions by labeling the product, thus enhancing user awareness of radiation protection.

RF Radiation Safety

To ensure the health and well-being of users, experts from the fields of science, engineering, medicine, health, and industry, along with relevant organizations, have jointly developed RF radiation standards and guidelines, as follows:

  • Title 47, Part 2, Subpart J of the Code of Federal Regulations (CFR) by the Federal Communications Commission (FCC) of the United States.
  • ANSI (American National Standards Institute) / IEEE (Institute of Electrical and Electronics Engineers) Standard C95.1-1992.
  • IEEE Standard C95.1-1999.
  • Standards issued in 1998 by the International Commission on Non-Ionizing Radiation Protection (ICNIRP).

RF Radiation Control and Operating Instructions

To ensure optimal performance and compliance with the radiation limits for occupational or controlled environments as specified in the standards, the transmission time should not exceed a duty cycle of 50% (i.e., a maximum of 50% transmission time). Adhere to the following instructions: RF energy radiation is only generated during transmission (talking), not during receiving (listening) or standby mode. Maintain a minimum distance of 2.5 centimeters between the device and the body during transmission.

2. Package Contents

The standard package for the BAJETON BJ7700 Walkie Talkie includes the following items:

  • 1 x Host (Radio Unit)
  • 1 x Battery
  • 1 x Back Clip
  • 1 x Type-C Charging Cable
  • 1 x Adapter
  • 1 x Hanging Rope
  • 1 x Instruction Manual
  • 1 x Antenna
Standard Package List for BAJETON BJ7700
Figure 2.1: Standard Package Contents for the BAJETON BJ7700 Walkie Talkie.

3. Product Overview and Features

The BAJETON BJ7700 is a multi-band walkie talkie designed for versatile communication. It offers a range of features including wide frequency coverage, optional Bluetooth programming, and intelligent noise reduction (for Bluetooth versions).

BAJETON BJ7700 Walkie Talkie with display showing frequency, spectrum analyzer, and key features
Figure 3.1: Overview of the BAJETON BJ7700 Walkie Talkie and its main features.
Multi-functional Walkie Talkie highlighting NOAA, HD Voice, Optional Bluetooth Phone APP Programming, Wireless Copy Frequency, Auto Power Save, VOX, Type-C Charger, Spectrum Analyzer
Figure 3.2: Multi-functional aspects of the BJ7700, including NOAA weather radio and HD Voice.

Key Features:

  • Bluetooth Phone Programming (Bluetooth version only): Allows swift input and adjustment of frequencies via a mobile app (iOS and Android compatible), eliminating complex cables.
  • Intelligent Noise Reduction (Bluetooth version only): Ensures clear voice communication even in noisy environments.
  • Spectrum Analyzer: Quickly identifies the strength of surrounding signals to avoid frequency collisions.
  • Full Band Coverage: Wide frequency ranges for both transmission and reception.
  • Wireless Copy Frequency: Enables easy and fast replication of frequencies between devices without manual programming.
  • NOAA Weather Radio: Supports timely reception of local and surrounding weather information.
  • Type-C Charging: Compatible with most Type-C chargers/power banks for fast and stable charging.
  • Customizable Side Keys: PF1, PF2, PF3 keys can be assigned to various functions.
  • Multiple Scanning Modes: Time Operation Mode (TO), Carrier Operating Mode (CO), Search Operation Mode (SE).
  • DTMF Encoding Transmission & PTT-ID Function: For advanced communication and identification.
  • VOX Function: Voice-operated transmission.
  • Wide/Narrow Bandwidth: Selectable for different communication needs.
  • 512 Channels: Ample storage for various frequencies.

Version Comparison: Standard vs. Bluetooth

The BAJETON BJ7700 is available in two versions: Standard and Bluetooth. Key differences are outlined below:

Comparison table of BJ7700 Standard Version vs. Bluetooth Version
Figure 3.3: Feature comparison between the Standard and Bluetooth versions of the BJ7700.
Table 3.1: Feature Comparison
Feature Standard Version Bluetooth Version
Bluetooth Phone APP Programming No Yes
Noise Reduction No Yes
Spectrum Analyzer Yes Yes
Frequency Range (TX/RX) 18-108MHz, 136-660MHz, 840-999MHz 18-108MHz, 136-580MHz, 760-999MHz
Frequency Range (RX only) 108-136MHz 108-136MHz
Power 5W 5W
Wireless Copy Frequency Yes Yes
Type-C Charger Yes Yes
NOAA Yes Yes
FM Radio Yes Yes
AM Radio Yes Yes

4. Specifications

Table 4.1: General Specifications
Attribute Value
Brand Name BAJETON
Model Number BJ7700
Walkie Talkie Type Portable
Maximum Range 5km-10km
Storage Channel 512
Battery Capacity High Capacity
Battery Included Yes
Is Display Yes
Waterproof / Water-Resistant No
Origin Mainland China
FCC ID 2BN9AUV8000

Frequency Ranges:

Frequency range for BJ7700 Ham Radio, comparing Standard and Bluetooth versions
Figure 4.1: Detailed frequency ranges for Standard and Bluetooth versions.
Table 4.2: Detailed Frequency Ranges
Band Standard Version (TX/RX) Bluetooth Version (TX/RX)
VHF/UHF 18-108 MHz (TX/RX) 18-108 MHz (TX/RX)
Airband 108-136 MHz (RX Only) 108-136 MHz (RX Only)
UHF 136-660 MHz (TX/RX) 136-580 MHz (TX/RX)
Extended UHF 840-999 MHz (TX/RX) 760-999 MHz (TX/RX)

Note: All transmission (TX) is FM only. Reception (RX) can be set to AM or FM on all frequencies. On bands such as CB, expect around 2 watts of TX power at best, and harmonics outside the 3 main ham bands may be present.

5. Setup

5.1 Charging Instructions

The BAJETON BJ7700 supports both dock charging and Type-C direct charging.

  1. Dock Charging (Optional): Insert the battery pack or the radio with the battery pack into the charging dock. Ensure proper contact with the charging terminals of the dock.
  2. Type-C Charging: Connect the provided charging cable to the power adapter and plug the power adapter into an AC power outlet. Insert the charging cable into the Type-C interface of the main unit's battery.
  3. Charging Indicator: When the device is charging, the red indicator light indicates charging in progress. The green indicator light indicates charging is complete.
Super Convenient Type-C Charging showing various charging methods
Figure 5.1: Various Type-C charging options for the BJ7700.

5.2 Super Mode Activation/Deactivation

If there are frequency restrictions in your region, you can activate or deactivate 'Super Mode' to adjust the frequency range.

  • To Turn On Super Mode: Press and hold the PTT key and the "8" key simultaneously while powering on the device.
  • To Exit Super Mode: Press and hold the PTT key and the "EXIT" key simultaneously while powering on the device.
Instructions for activating and exiting Super Mode on the BJ7700
Figure 5.2: Visual guide for Super Mode activation and deactivation.

5.3 Bluetooth Phone APP Programming (Bluetooth Version Only)

For the Bluetooth version, you can program the walkie talkie using a mobile application. This simplifies frequency input and adjustments.

  1. Download the official programming application by scanning the QR codes provided below. The app supports both iOS and Android devices.
  2. Pair your mobile device with the walkie talkie via Bluetooth.
  3. Use the app interface to input and adjust frequencies and other settings.
QR codes for downloading the Bluetooth Programming APP for iOS and Android
Figure 5.3: QR codes for downloading the Bluetooth Programming App.

Note: Some users have reported that the Bluetooth programming app can be clunky, slow, and may not include all programming options. Manual programming via the radio's interface or using compatible third-party software (if available) might be necessary for full functionality.

6. Operating Instructions

6.1 Interface Icon Descriptions

Familiarize yourself with the icons displayed on the walkie talkie's screen:

Table 6.1: Interface Icon Descriptions
Icon Description
CTAnalog Sub-audio Tone Indicator. Indicates current sub-audio tone is analog.
DCSDigital Sub-audio Tone Indicator. Indicates current sub-audio tone is digital.
HHigh Power Indicator. Current transmission power is set to high.
MMedium Power Indicator. Current transmission power is set to medium.
LLow Power Indicator. Current transmission power is set to low.
NNarrowband Mode Indicator. Channel is operating in narrowband mode.
WWideband Mode Indicator. Channel is operating in wideband mode.
+Frequency Mode (+ Frequency Offset). Transmission frequency is reception frequency plus offset.
-Frequency Mode (- Frequency Offset). Transmission frequency is reception frequency minus offset.
RFrequency/Channel Mode Inverted Frequency. Reception and transmission frequencies are inverted.
TSimplex Mode. Reception and transmission frequencies are adjusted to be the same.
SCSC (Encryption) Indicator. Encryption function is enabled.
AMAM Modulation Indicator. Current frequency is in AM modulation mode.
SCRScrambler Function. Scrambler function is active.
VOXVOX (Voice-Operated Transmission). VOX function is enabled.
DWDual Standby. Dual-band standby function is set and active.
MOMonitor Function Enabled. Monitor function is enabled.
Side Tone IconSide Tone Enabled. Side tone function is active, producing a tone sound when transmitting DTMF.
Keypad Lock IconKeypad Lock. Appears when the keypad is locked. Long press the # key to unlock.
RSSISignal Strength. Indicates the strength of the received signal.
A/BA/B Band. Indicates whether the A band or B band is active.
VOLTransmit Audio Volume. Indicates the volume level of the transmitted audio.
Battery Status IconBattery Status. Displays remaining battery power. Flashes when nearly depleted, transmission prohibited. Green outer frame indicates super power-saving mode.
Bluetooth IconEnable the Bluetooth connection function.

6.2 Basic Operations

  • Main Frequency Selection: In standby mode, press the [A/B] key to switch between A/B bands.
  • PTT Function: Press PTT button 1 to transmit on frequency band A; press PTT button 2 to transmit on frequency band B.
  • Channel Mode / Frequency Mode Switching: In standby mode, press [V/M] to switch between frequency mode and channel mode. If the channel list has no valid channels, switching to channel mode is not possible.
  • PF1 Side Key Function: Configure the side key function via navigation software. Functions include: radio, TX power, scanning, search, monitor, weather forecast, and SOS.
  • Keypad Lock / Unlock: Long press [#] in standby mode to lock/unlock the keypad.
  • Dual-band Standby: Enable dual-band standby via "Menu - Radio Settings - Dual-band Standby". Once enabled, you can monitor both primary and secondary frequencies without switching.
  • Voice Control Function (VOX): Enable via "Menu - Voice-operated Function - Voice-operated Switch - On". Transmission starts when the microphone detects a sufficiently loud sound. The voice control level can be set through the menu.
  • Voice Control Delay: Set via "Menu - Radio Settings - Voice-operated Delay" to define how long voice control detection remains active.
  • FM Radio: Assign the side key function to the radio. Supports 65-76/76-108 MHz. Use [PF1] to switch bands, numeric keypad for direct frequency input, and short press # for auto search.
  • Frequency Scanning Function: Assign the side key function to frequency scanning. Detects transmitter carrier frequency and sub-audio frequency information. Press [PF1] to save scanned frequency.
  • SOS Function: Assign to the Alarm key. Supports local alarm, transmit alarm tone, and transmit alarm code. Configurable via "Menu - Radio Settings - SOS Mode".
  • Scanning Function: Supports channel list scanning and frequency step scanning. Configurable via "Menu - Radio Settings - Scanning Mode". Methods: Time (resumes after 5s if no action), Carrier (stops on signal, resumes after 5s), Search (stops on signal).
  • PTT-ID Function: Transmit identity or call codes via DTMF. 15 sets of call codes configurable via "Menu - Signaling Settings - DTMF". Transmission methods: Send on Press, Send on Release, Send Both.
Side Key Custom Buttons diagram, showing programmable functions
Figure 6.1: Customizable side keys and their potential functions.
BAJETON BJ7700 with NOAA Weather Radio logo
Figure 6.2: NOAA Weather Radio feature for timely weather information.
Spectrum Analyzer feature, explaining its use to quickly identify signal strength
Figure 6.3: Spectrum Analyzer for identifying signal strength and avoiding frequency collisions.
Fast Copy one Channel feature, illustrating how to identify and save frequencies
Figure 6.4: Wireless Copy Frequency feature for quick channel replication.

6.3 Menu Function List

The following tables detail the menu options and their settings:

Table 6.2: Menu Function List (Part 1)
First-level Menu Secondary Menu Third-level Menu Setting Instructions
SettingSQLOFF, 0-9Adjust squelch level. Lower for easier interference, higher for worse sensitivity.
SettingTrans PowerHigh, Middle, LowSelect walkie-talkie output power level.
SettingBandwidthWide, NarrowSet to wideband FM (±25K) or narrowband FM (±12.5K).
SettingVOX Delay0.5sec-2.0secDelay time for turning off PTT after voice-activated transmission.
SettingDual StandbyOFF, ONWhen ON, both frequency bands are in standby, ready to receive.
SettingBattery SaveOFF, Normal, Super DeepConserves power and extends standby time.
SettingBusy LockoutOFF, ONPrevents conflicts if channel is in use. PTT will not initiate transmission when ON.
SettingTOTOFF, 30,60,90...240secTransmission ceases after preset duration. Walkie-talkie emits alert tone.
SettingTALLOFF, ONWhen ON, transmitter sends signal to receiver to shut off audio channel, then ceases transmission.
SettingNoise ReductionOFF, ONEnables or disables noise reduction.
SettingR-TONE1000hz, 1450hz, 1750hz, 2100hzCommand used to connect to a repeater station.
SettingScan ModeTime, Carrier, SearchTime: pauses 5s on signal, resumes. Carrier: pauses on signal, stays on freq. Search: stops on signal, stays on freq.
SettingPROGREOFF, BEEP, TONE1200Turn Off, Turn ON, TONE1200.
SettingRP-STEOFF, 100ms-1000msAdjust repeater transmission delay to eliminate noise. Set to OFF if noise confirms repeater is working.
Table 6.3: Menu Function List (Part 2)
First-level Menu Secondary Menu Third-level Menu Setting Instructions
DTMFS-CODECODE1-CODE15Select DTMF code.
DTMFPTT-IDOFF, BOT, EOT, BOTHOFF: No PTT-ID. BOT: Send on PTT press. EOT: Send on PTT release. BOTH: Send on both.
DTMFDTMFSTOFF, DT-ST, ANI-ST, DT+ANIOFF: No DTMF prompt. DT-ST: DTMF prompt on key press. ANI-ST: Auto DTMF. DT+ANI: Auto DTMF and key press.
SIDE KEYPF11.RADIO, 2.TX POWER, 3.SCAN, 4.SEARCH, 5.MONI, 6.NOAA, 7.SOSSelect function for short press of PF1.
SIDE KEYLONG PF11.RADIO, 2.TX POWER, 3.SCAN, 4.SEARCH, 5.MONI, 6.NOAA, 7.SOSSelect function for long press of PF1.
ABOUTABOUTANICODE, Software version, Hardware versionDisplays ANICODE (123), Software version (V0.01), Hardware version (V1.00).
RESETRESETVFO Mode, Reset AllVFO Mode: Menu back to factory setting. Reset All: Menu and channel back to factory setting.
BLEBLEOFF, ONTurn off/on Bluetooth connection features.
VFO&CHStep2.5/5.0/6.25/...50KHZSet the VFO frequency tuning step value.
VFO&CHDirectionNone, Plus, MinusSet whether transmission frequency is higher (Plus) or lower (Minus) than reception frequency.
VFO&CHOffset00.000-99.995In frequency mode, the difference between transmitting and receiving frequencies.
VFO&CHCH-MemoryCH-001-CH-256Indicate channel number to be stored. 'CH' means channel has parameters.
VFO&CHCH-DeleteCH-001-CH-256Delete channel parameters. No 'CH' means no parameters, operation invalid.
CDCSSRX CTCSSOFF, 67.0-254.1Select to receive analog sub-audible tones.
CDCSSRX DCSOFF, D023N-D754NSelect to receive digital sub-audible tones.
CDCSSTX CTCSSOFF, 67.0-254.1Select to transmit analog sub-audible tones.
CDCSSTX DCSOFF, D023N-D754NSelect to transmit digital sub-audible tones.
CDCSSEncryptionON, OFFEnable or disable voice encryption.
AdvancedBeep PromptOFF, ONKey Operation Prompt Tone.
AdvancedVoiceOFF, ONTurn off/on voice prompt.
AdvancedKeypad LockOFF, 5S, 10S, 15STurn off auto keypad lock or set timing for automatic lock.
AdvancedBack LightON, 5s/10s...3minBackground light always on or set time for auto-off.
AdvancedMenu OutTime5/10...60secControl the auto-exit time for the menu.
AdvancedLanguageEnglish, ChineseSelect display language.

7. Maintenance

7.1 Daily Maintenance

  • Do not pierce or scratch the product with hard objects.
  • Do not store the product in environments containing chemical corrosive substances.
  • Do not carry or use the product by pulling the earphone cable.
  • When not using the earphone jack, cover the interface with the protective cap.

7.2 Cleaning Procedure

Before cleaning, please power off the device and remove the battery:

  1. Regularly use a dry, clean, lint-free cloth or a soft brush to remove dust from the product surface and charging terminals.
  2. If the buttons or casing become dirty, use a neutral detergent and a non-woven cloth for cleaning. Do not use detergents, alcohol, sprays, or petroleum-based chemicals as they may damage the surface casing.
  3. After cleaning, ensure the product is completely dry before use.

8. Troubleshooting

  • Radio only turns off when shaken: This may indicate a loose connection between the battery and the main board. Ensure the battery is securely seated. If the issue persists, contact support.
  • Bluetooth programming app issues: Some users report the Android/iOS app being clunky, slow, or not listing the BJ-7700 model. If the app is not working effectively, consider manual programming via the radio's menu or exploring third-party programming software (e.g., CHIRP, though compatibility is not guaranteed).
  • Difficulty finding Windows programming software: Official Windows programming software may not be readily available or easy to find. Check the manufacturer's website or community forums for compatible options.
  • Radio not turning off Bluetooth: If the radio does not show Bluetooth in the menu, it might be a non-Bluetooth version. Verify your product version against the packaging or purchase details.
  • Weak battery after short charge: If the battery charges very quickly (e.g., 1 hour) but seems weak, it might indicate a faulty battery or charger. Ensure you are using the provided charger and cable.
  • Harmonics on certain bands: On bands like 27MHz, 50MHz, and 70MHz, the radio may transmit more power on harmonic frequencies than the tuned frequency. This is a characteristic of the radio's design for these specific bands.

9. User Tips

  • Programming: While the Bluetooth app can be used for programming, some users find manual frequency changes on the VFO (Variable Frequency Oscillator) to be effective for occasional adjustments.
  • Reception Quality: The radio generally offers very clear RX/TX with good reception, especially with the stock antenna. Air band reception is surprisingly good. The sensitivity is noted to be excellent in the 2m and 70cm bands.
  • CB Band Usage: When transmitting on the CB band, be aware that TX is FM only. While you can listen to all CB transmissions (AM or FM), you will only be able to communicate with other CB radios that support FM modulation. Expect around 2 watts of TX power on CB.
  • General Use: The BJ7700 is a robust and simple-to-use unit, suitable for various outdoor activities like camping, hiking, cycling, and skiing.
Collage of people using walkie-talkies in various outdoor activities
Figure 9.1: The BAJETON BJ7700 is suitable for a variety of outdoor uses.

10. Frequently Asked Questions (FAQ)

Q: Once in Super Mode, can I configure the radio to transmit on the 108-136 MHz AM band?
A: The 108-136 MHz band is typically for aviation reception (RX only) and is AM modulated. The BJ7700's specifications indicate this band is RX only. Transmission on this band is generally not supported.
Q: Does this radio listen and transmit at 220MHz?
A: Based on the provided frequency ranges, the radio supports TX/RX in the 136-660 MHz (Standard) or 136-580 MHz (Bluetooth) range, which includes 220MHz. Therefore, it should be able to listen and transmit at 220MHz within these ranges.

11. Warranty Terms

The warranty period for this product starts from the date of sale (based on the date on the sales invoice). The main unit is covered for 12 months, and the battery and charging accessories are covered for 6 months. The following cases will require paid repair services during the warranty period:

  1. Failure to present this warranty card and the purchase invoice.
  2. This card shows signs of alteration or does not match the product.
  3. Defects and damages caused by using this product under non-standard conditions.
  4. Defects and damages caused by misuse, accidents, water ingress, or negligence.
  5. Defects and damages resulting from improper testing, operation, repair, installation, modification, or adjustment.
  6. Defects and damages caused by unauthorized repairs or disassembly.
  7. Defects and damages caused by force majeure.
  8. Normal wear and tear from regular use.

This warranty card serves as an important proof for the end user to enjoy warranty services. It must be stamped and filled out completely by an authorized dealer to be valid. Please keep it safe.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.