WOYO PL007 PRO 3.0 CAN BUS Tester User Manual

1. Introduction

The WOYO PL007 PRO 3.0 is a digital tester specifically designed for automotive electronics. It provides a compact and user-friendly solution for diagnosing communication issues in vehicle systems. This device can detect the communication status of CAN (Controller Area Network), LIN (Local Interconnect Network), and PWM (Pulse Width Modulation) lines, displaying data, ID, and baud rate. It is an essential tool for both professional technicians and DIY enthusiasts working with automotive electrical modules.

2. Safety Information

• Always wear appropriate personal protective equipment, such as safety glasses, when working on vehicles.
• Ensure the vehicle's ignition is off and the battery is disconnected before connecting or disconnecting the tester, unless specific instructions state otherwise.
• Do not use the tester if it appears damaged or if any cables are frayed.
• Avoid contact with moving engine parts or hot surfaces.
• Keep the device dry and away from liquids.
• This device is intended for automotive diagnostic use only. Do not use it for purposes other than its intended function.

3. Package Contents

Verify that all items are present in your package:

• Main Tester Unit (PL007 PRO)
• Wireless Signal Receiver
• Storage Bag
• Long Chain (for receiver)

Note: 9V and CR2032 3V batteries are NOT included in the package and must be purchased separately.

4. Product Overview

The WOYO PL007 PRO 3.0 is a versatile diagnostic tool featuring a main tester unit and a wireless signal receiver for enhanced flexibility.

4.1 Main Tester Unit

The main unit features a display screen and control buttons for selecting modes and viewing data.

• ON/OFF Button: Long press for over 3 seconds to turn the device on or off.
• Mode Switch Button: Cycles through CAN Probe (CAN BUS Mode), LIN Probe (LIN BUS Mode), and SIGN Probe (PWM Signal Mode).
• Data/Signal Button: In CAN/LIN mode, long press to start sending signals (select '01' or '10' mode). Short press to stop ID page and view data.

4.2 Wireless Signal Receiver

The wireless signal receiver allows for remote monitoring of CAN/LIN signals, indicated by an LED light.

5. Specifications

6. Setup

6.1 Main Tester Unit Battery Installation

1. Locate the battery compartment on the back of the main tester unit.
2. Open the compartment cover.
3. Insert a 9V battery, ensuring correct polarity.
4. Close the battery compartment cover securely.

6.2 Wireless Signal Receiver Battery Installation and Pairing

1. Remove the clip/cover from the wireless signal receiver.
2. Install a CR2032 3V battery, paying attention to the positive (+) direction.
3. Turn on the receiver using its ON/OFF button. The LED should turn green.
4. On the PL007 PRO main unit, press and hold the right button (signal button) to initiate pairing.
5. On the receiver, press and hold the reset button for over 3 seconds until its LED flashes blue and red.
6. Once successfully connected, the LEDs will indicate a stable connection. Cover the clip back onto the receiver.

7. Operating Instructions

7.1 General Operation

• Power On/Off: Long press the ON/OFF button (center button) for over 3 seconds.
• Switch Modes: Use the left button to cycle between CAN Probe, LIN Probe, and SIGN Probe (PWM) modes.

7.2 CAN Mode (CAN BUS Mode)

This mode is used to test CAN BUS communication lines. The device automatically recognizes CAN-High and CAN-Low and detects the baud rate.

1. Select 'CAN Probe' mode using the mode switch button.
2. Connect the tester's probes to the CAN-High and CAN-Low lines of the vehicle's OBD/OBD II port or specific module. Ensure the cables are indeed CAN BUS cables.
3. The display will show the detected BAUD rate and CAN-H/CAN-L status. If communication is active, data frames (ID and values) will be displayed.
4. To send a signal, long press the right button. To stop sending and view data, short press the right button.
5. The wireless signal receiver's LED will flash red and blue if it receives a CAN/LIN signal, or red and blue if no signal is detected.

Video 7.1: Demonstration of WOYO PL007 PRO 3.0 in CAN, LIN, and Signal Modes.

7.3 LIN Mode (LIN BUS Mode)

This mode is used to test LIN BUS communication lines.

1. Select 'LIN Probe' mode using the mode switch button.
2. Connect the red probe to the LIN line and the black probe to GND (Ground).
3. The display will show the detected BAUD rate and LIN data frames.
4. The wireless signal receiver's LED will flash red and blue if it receives a CAN/LIN signal, or red and blue if no signal is detected.

7.4 PWM Signal Mode (SIGN Probe)

This mode is used to check PWM emulate signals and measure voltage.

1. Select 'SIGN Probe' mode using the mode switch button.
2. Connect the red probe to the signal line and the black probe to GND (Ground).
3. The display will show the detected PWM signal and its voltage (Max Voltage: < 20V).

8. User Tips

• Always double-check your connections before powering on the device to avoid damage.
• If a mode shows no data, try switching to another mode (e.g., if CAN mode shows nothing, check PWM mode) to ensure the correct signal type is being analyzed.
• Keep the wireless signal receiver within a reasonable range of the main unit for optimal performance.

9. Maintenance

• Clean the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Store the tester and its accessories in the provided storage bag in a cool, dry place when not in use.
• Remove batteries if the device will not be used for an extended period to prevent leakage.
• Regularly check the probes and cables for any signs of wear or damage. Replace if necessary.

10. Troubleshooting

11. Warranty and Support

This product comes with a standard manufacturer's warranty. For specific warranty details, technical support, or service inquiries, please refer to the product's official website or contact the seller directly. Keep your purchase receipt as proof of purchase.